On 09/19/17 11:50, Dave Stevenson wrote:
> Hi Eric.
>
> Thanks for the review.
>
> On 18 September 2017 at 19:18, Eric Anholt <eric@xxxxxxxxxx> wrote:
>> Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx> writes:
>>> diff --git a/drivers/media/platform/bcm2835/bcm2835-unicam.c b/drivers/media/platform/bcm2835/bcm2835-unicam.c
>>> new file mode 100644
>>> index 0000000..5b1adc3
>>> --- /dev/null
>>> +++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c
>>> @@ -0,0 +1,2192 @@
>>> +/*
>>> + * BCM2835 Unicam capture Driver
>>> + *
>>> + * Copyright (C) 2017 - Raspberry Pi (Trading) Ltd.
>>> + *
>>> + * Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
>>> + *
>>> + * Based on TI am437x driver by Benoit Parrot and Lad, Prabhakar and
>>> + * TI CAL camera interface driver by Benoit Parrot.
>>> + *
>>
>> Possible future improvement: this description of the driver is really
>> nice and could be turned into kernel-doc.
>
> Documentation?! Surely not :-)
> For now I'll leave it as a task for another day.
>
>>> + * There are two camera drivers in the kernel for BCM283x - this one
>>> + * and bcm2835-camera (currently in staging).
>>> + *
>>> + * This driver is purely the kernel control the Unicam peripheral - there
>>
>> Maybe "This driver directly controls..."?
>
> Will do in v3.
>
>>> + * is no involvement with the VideoCore firmware. Unicam receives CSI-2
>>> + * or CCP2 data and writes it into SDRAM. The only processing options are
>>> + * to repack Bayer data into an alternate format, and applying windowing
>>> + * (currently not implemented).
>>> + * It should be possible to connect it to any sensor with a
>>> + * suitable output interface and V4L2 subdevice driver.
>>> + *
>>> + * bcm2835-camera uses with the VideoCore firmware to control the sensor,
>>
>> "uses the"
>
> Will do in v3.
>
>>> + * Unicam, ISP, and all tuner control loops. Fully processed frames are
>>> + * delivered to the driver by the firmware. It only has sensor drivers
>>> + * for Omnivision OV5647, and Sony IMX219 sensors.
>>> + *
>>> + * The two drivers are mutually exclusive for the same Unicam instance.
>>> + * The VideoCore firmware checks the device tree configuration during boot.
>>> + * If it finds device tree nodes called csi0 or csi1 it will block the
>>> + * firmware from accessing the peripheral, and bcm2835-camera will
>>> + * not be able to stream data.
>>
>> Thanks for describing this here!
>>
>>> +/*
>>> + * The peripheral can unpack and repack between several of
>>> + * the Bayer raw formats, so any Bayer format can be advertised
>>> + * as the same Bayer order in each of the supported bit depths.
>>> + * Use lower case to avoid clashing with V4L2_PIX_FMT_SGBRG8
>>> + * formats.
>>> + */
>>> +#define PIX_FMT_ALL_BGGR v4l2_fourcc('b', 'g', 'g', 'r')
>>> +#define PIX_FMT_ALL_RGGB v4l2_fourcc('r', 'g', 'g', 'b')
>>> +#define PIX_FMT_ALL_GBRG v4l2_fourcc('g', 'b', 'r', 'g')
>>> +#define PIX_FMT_ALL_GRBG v4l2_fourcc('g', 'r', 'b', 'g')
>>
>> Should thes fourccs be defined in a common v4l2 header, to reserve it
>> from clashing with others later?
>
> I'm only using them as flags and probably in a manner that nothing
> else is likely to copy, so it seems a little excessive to put them in
> a common header.
> Perhaps it's better to switch to 0xFFFFFFF0 to 0xFFFFFFF3 or other
> value that won't come up as a fourcc under any normal circumstance.
> Any thoughts from other people?
I think that's better, yes.
>
>> This is really the only question I have about this driver before seeing
>> it merged. As far as me wearing my platform maintainer hat, I'm happy
>> with the driver, and my other little notes are optional.
>>
>>> +static int unicam_probe(struct platform_device *pdev)
>>> +{
>>> + struct unicam_cfg *unicam_cfg;
>>> + struct unicam_device *unicam;
>>> + struct v4l2_ctrl_handler *hdl;
>>> + struct resource *res;
>>> + int ret;
>>> +
>>> + unicam = devm_kzalloc(&pdev->dev, sizeof(*unicam), GFP_KERNEL);
>>> + if (!unicam)
>>> + return -ENOMEM;
>>> +
>>> + unicam->pdev = pdev;
>>> + unicam_cfg = &unicam->cfg;
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> + unicam_cfg->base = devm_ioremap_resource(&pdev->dev, res);
>>> + if (IS_ERR(unicam_cfg->base)) {
>>> + unicam_err(unicam, "Failed to get main io block\n");
>>> + return PTR_ERR(unicam_cfg->base);
>>> + }
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>>> + unicam_cfg->clk_gate_base = devm_ioremap_resource(&pdev->dev, res);
>>> + if (IS_ERR(unicam_cfg->clk_gate_base)) {
>>> + unicam_err(unicam, "Failed to get 2nd io block\n");
>>> + return PTR_ERR(unicam_cfg->clk_gate_base);
>>> + }
>>> +
>>> + unicam->clock = devm_clk_get(&pdev->dev, "lp_clock");
>>> + if (IS_ERR(unicam->clock)) {
>>> + unicam_err(unicam, "Failed to get clock\n");
>>> + return PTR_ERR(unicam->clock);
>>> + }
>>> +
>>> + ret = platform_get_irq(pdev, 0);
>>> + if (ret <= 0) {
>>> + dev_err(&pdev->dev, "No IRQ resource\n");
>>> + return -ENODEV;
>>> + }
>>> + unicam_cfg->irq = ret;
>>> +
>>> + ret = devm_request_irq(&pdev->dev, unicam_cfg->irq, unicam_isr, 0,
>>> + "unicam_capture0", unicam);
>>
>> Looks like there's no need to keep "irq" in the device private struct.
>
> Agreed. I'll remove in v3.
>
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "Unable to request interrupt\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + ret = v4l2_device_register(&pdev->dev, &unicam->v4l2_dev);
>>> + if (ret) {
>>> + unicam_err(unicam,
>>> + "Unable to register v4l2 device.\n");
>>> + return ret;
>>> + }
>>> +
>>> + /* Reserve space for the controls */
>>> + hdl = &unicam->ctrl_handler;
>>> + ret = v4l2_ctrl_handler_init(hdl, 16);
>>> + if (ret < 0)
>>> + goto probe_out_v4l2_unregister;
>>> + unicam->v4l2_dev.ctrl_handler = hdl;
>>> +
>>> + /* set the driver data in platform device */
>>> + platform_set_drvdata(pdev, unicam);
>>> +
>>> + ret = of_unicam_connect_subdevs(unicam);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "Failed to connect subdevs\n");
>>> + goto free_hdl;
>>> + }
>>> +
>>> + /* Enabling module functional clock */
>>> + pm_runtime_enable(&pdev->dev);
>>
>> I think pm_runtime is only controlling the power domain for the PHY, not
>> the clock (which you're handling manually).
>
> You're right. Copy and paste from the driver I'd based this on.
> Will correct in v3.
>
> Dave
>
Dave, I plan to review this Friday or Monday. It would help me if you could
post a v3 before Friday so that I'm reviewing the latest code.
It would be great if you can also post your tc358743 patches. I have an RPi
with a tc358743 attached, so it would be very useful if I can review and test
both this driver and the tc358743 changes.
I also have a selfish motive: I want to do a CEC demo next week during the
Kernel Recipes conference with my RPi/tc358743 and your driver. It's nice if
I can use the latest version for that.
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
