Add device-tree binding documentation SFP transceivers. Support for SFP
transceivers has been recently introduced (drivers/net/phy/sfp.c).
Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
---
v4:
Remove redundant 'single' from the gpio specifier
Rename 'moddef0-gpios' property to 'mod-def0-gpios'
Remove 'phy-mode' property from the example; SFP determines the mode
v3:
Mention gpios phandle and specifier
Mention the polarity of each gpio
Fix example property names
v2:
Rename -gpio properties to -gpios
Rename the rate-select-gpio property to rate-select0-gpios
Add the rate-select1-gpios property
Add examples
---
Documentation/devicetree/bindings/net/sff,sfp.txt | 76 +++++++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sff,sfp.txt
diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt
new file mode 100644
index 000000000000..60e970ce10ee
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sff,sfp.txt
@@ -0,0 +1,76 @@
+Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
+Transceiver
+
+Required properties:
+
+- compatible : must be "sff,sfp"
+
+Optional Properties:
+
+- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
+ interface
+
+- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
+ module presence input gpio signal, active (module absent) high
+
+- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
+ Indication input gpio signal, active (signal lost) high
+
+- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
+ Fault input gpio signal, active (fault condition) high
+
+- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
+ output gpio signal, active (Tx disable) high
+
+- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
+ Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
+
+- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
+ Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
+ high Tx rate
+
+Example #1: Direct serdes to SFP connection
+
+sfp_eth3: sfp-eth3 {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_1g_i2c>;
+ los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
+ tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
+};
+
+&cps_emac3 {
+ phy-names = "comphy";
+ phys = <&cps_comphy5 0>;
+ sfp = <&sfp_eth3>;
+};
+
+Example #2: Serdes to PHY to SFP connection
+
+sfp_eth0: sfp-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfpp0_i2c>;
+ los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cps_sfpp0_pins>;
+ tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
+};
+
+p0_phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
+ reg = <0>;
+ interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
+ sfp = <&sfp_eth0>;
+};
+
+&cpm_eth0 {
+ phy = <&p0_phy>;
+ phy-mode = "10gbase-kr";
+};
--
2.14.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
