Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports & 2x USB via headers
Signed-off-by: Antony Antony <antony@xxxxxxxxxxx>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts | 229 +++++++++++++++++++++
2 files changed, 230 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
---
Changes
v1 -> v2
add wifi power controller, mmc1, mmc2
remove reg_usb0_vbus
v2 -> v3
fix typo s/orangepi/nanopi/, s/pus/plus/
usb_otg set to host mode
wifi fix, based on commit 442e1f7e brcm,bcm43xx-fmac.txt
remove functions on header pins: spi, ir, ehci 1&2, ohci 1&2, uart 1&2
remove hdmi, de2, r-gpio-keys, mixer - not supported the board
v3->v4 update WiFi chip compatible to bcm43430-fmac
v4->v5 back to bcm4329-fmac bcm43430-fmac is the wrong way.
v5-->v6
sorted nodes
removed usb0_id_det-gpios,boot_device, drive-strength = <40>; boot_device
delete nodes which are same as the defaults.
v6->v7
s/brcm,bcm4329-fmac/brcm/
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 108f12c..e6810c8 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
new file mode 100644
index 0000000..abea712
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts
@@ -0,0 +1,229 @@
+/*
+ * Copyright (C) 2017 Antony Antony <antony@xxxxxxxxxxx>
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "FriendlyARM NanoPi NEO Plus2";
+ compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "nanopi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "nanopi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_cpux_r_npi>;
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+ /*
+ * AMPAK AP6212A WiFi module with BCM43430, rev=1 inside
+ * sdio vendor ID: 0x02d0, sdio device ID: 0xa9a6
+ */
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ boot_device = <0>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&r_pio {
+ leds_r_npi: led_pins@0 {
+ pins = "PL10";
+ function = "gpio_out";
+ };
+
+ vdd_cpux_r_npi: regulator_pins@0 {
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB Type-A ports' VBUS is always on */
+ status = "okay";
+};
--
2.9.3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
