Hi Eric,
On Thu, 31 Aug 2017 10:03:23 -0700
Eric Anholt <eric@xxxxxxxxxx> wrote:
> Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx> writes:
>
> > Add a driver for Cadence DPI -> DSI bridge.
> >
> > This driver only support a subset of Cadence DSI bridge capabilities.
> >
> > Here is a non-exhaustive list of missing features:
> > * burst mode
> > * dynamic configuration of the DPHY based on the
> > * support for additional input interfaces (SDI input)
> >
> > Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
> > ---
> > Changes in v3:
> > - replace magic values by real timing calculation. The DPHY PLL clock
> > is still hardcoded since we don't have a working DPHY block yet, and
> > this is the piece of HW we need to dynamically configure the PLL
> > rate based on the display refresh rate and the resolution.
> > - parse DSI devices represented with the OF-graph. This is needed to
> > support DSI devices controlled through an external bus like I2C or
> > SPI.
> > - use the DRM panel-bridge infrastructure to simplify the DRM panel
> > logic
>
> Just a few comments from me. With the few straightforward nitpicks
> fixed, it gets my:
>
> Acked-by: Eric Anholt <eric@xxxxxxxxxx>
>
> > +static enum drm_mode_status
> > +cdns_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> > + const struct drm_display_mode *mode)
> > +{
> > + struct cdns_dsi_input *input = bridge_to_cdns_dsi_input(bridge);
> > + struct cdns_dsi *dsi = input_to_dsi(input);
> > + struct cdns_dsi_output *output = &dsi->output;
> > + int bpp;
> > +
> > + /*
> > + * VFP_DSI should be less than VFP_DPI and VFP_DSI should be at
> > + * least 1.
> > + */
> > + if (mode->vtotal - mode->vsync_end < 2)
> > + return MODE_V_ILLEGAL;
> > +
> > + /* VSA_DSI = VSA_DPI and must be at least 2. */
> > + if (mode->vsync_end - mode->vsync_start < 2)
> > + return MODE_V_ILLEGAL;
> > +
> > + /* HACT must be a 32-bits aligned. */
>
> s/a /
>
> > + bpp = mipi_dsi_pixel_format_to_bpp(output->dev->format);
> > + if ((mode->hdisplay * bpp) % 32)
> > + return MODE_H_ILLEGAL;
> > +
> > + return MODE_OK;
> > +}
>
>
> > +static void cdns_dsi_bridge_enable(struct drm_bridge *bridge)
> > +{
> > + struct cdns_dsi_input *input = bridge_to_cdns_dsi_input(bridge);
> > + struct cdns_dsi *dsi = input_to_dsi(input);
> > + struct cdns_dsi_output *output = &dsi->output;
> > + u32 hsize0, hsa, hline, tmp, reg_wakeup, div;
> > + unsigned long dphy_pll_period, tx_byte_period;
> > + struct drm_display_mode *mode;
> > + int bpp, nlanes;
> > +
> > + mode = &bridge->encoder->crtc->state->adjusted_mode;
> > + bpp = mipi_dsi_pixel_format_to_bpp(output->dev->format);
> > + nlanes = output->dev->lanes;
> > +
> > + if (output->dev->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> > + tmp = mode->crtc_htotal - mode->crtc_hsync_end;
> > + else
> > + tmp = mode->crtc_htotal - mode->crtc_hsync_start;
> > + tmp = (tmp * bpp) / 8;
> > + tmp = tmp < DSI_HBP_FRAME_OVERHEAD ? 0 : tmp - DSI_HBP_FRAME_OVERHEAD;
> > + hsize0 = HBP_LEN(tmp);
> > +
> > + tmp = mode->crtc_hsync_start - mode->crtc_hdisplay;
> > + tmp = (tmp * bpp) / 8;
>
> How is this scaling supposed to work when you have RGB666_PACKED (bpp =
> 18)? It seems like there would be bad rounding issues.
That's a good question. The spec does not say anything about rounding,
but I guess rounding up is safer. Richard, any opinion on that?
>
> > + tmp = tmp < DSI_HFP_FRAME_OVERHEAD ? 0 : tmp - DSI_HFP_FRAME_OVERHEAD;
> > + hsize0 |= HFP_LEN(tmp);
> > +
> > + if (output->dev->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> > + tmp = mode->crtc_hsync_end - mode->crtc_hsync_start;
> > + else
> > + tmp = 0;
> > + tmp = (tmp * 8) / bpp;
>
> This scaling is suspiciously different from the others around it. Did
> you mean this?
It's a mistake, I'll fix that.
>
> > + tmp = tmp < DSI_HSA_FRAME_OVERHEAD ? 0 : tmp - DSI_HSA_FRAME_OVERHEAD;
> > + hsa = tmp;
> > + hsize0 |= HSA_LEN(tmp);
> > +
> > + writel(hsize0, dsi->regs + VID_HSIZE1);
> > + writel((mode->crtc_hdisplay * bpp) / 8, dsi->regs + VID_HSIZE2);
> > +
> > + writel(VBP_LEN(mode->crtc_vtotal - mode->crtc_vsync_end - 1) |
> > + VFP_LEN(mode->crtc_vsync_start - mode->crtc_vdisplay) |
> > + VSA_LEN(mode->crtc_vsync_end - mode->crtc_vsync_start),
> > + dsi->regs + VID_VSIZE1);
> > + writel(mode->crtc_vdisplay, dsi->regs + VID_VSIZE2);
> > +
> > + hline = (mode->crtc_htotal * bpp) / 8;
> > + tmp = hline - DSI_HSA_FRAME_OVERHEAD;
> > + if (output->dev->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> > + tmp -= hsa + DSI_HSA_FRAME_OVERHEAD;
> > +
> > + writel(BLK_LINE_PULSE_PKT_LEN(tmp), dsi->regs + VID_BLKSIZE2);
> > + if (output->dev->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> > + writel(MAX_LINE_LIMIT(tmp - DSI_NULL_FRAME_OVERHEAD),
> > + dsi->regs + VID_VCA_SETTING2);
> > +
> > + tmp = hline -
> > + (DSI_HSS_VSS_VSE_FRAME_OVERHEAD + DSI_BLANKING_FRAME_OVERHEAD);
> > + writel(BLK_LINE_EVENT_PKT_LEN(tmp), dsi->regs + VID_BLKSIZE1);
> > + if (!(output->dev->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE))
> > + writel(MAX_LINE_LIMIT(tmp - DSI_NULL_FRAME_OVERHEAD),
> > + dsi->regs + VID_VCA_SETTING2);
> > +
> > + tmp = DIV_ROUND_UP(hline, nlanes) - DIV_ROUND_UP(hsa, nlanes);
> > +
> > + if (!(output->dev->mode_flags & MIPI_DSI_MODE_EOT_PACKET))
> > + tmp -= DIV_ROUND_UP(DSI_EOT_PKT_SIZE, nlanes);
> > +
> > + dphy_pll_period = NSEC_PER_SEC / DPHY_PLL_RATE_HZ;
> > + tx_byte_period = (dphy_pll_period * 2) / 8;
> > + reg_wakeup = REG_WAKEUP_TIME_NS / dphy_pll_period;
> > + writel(REG_WAKEUP_TIME(reg_wakeup) | REG_LINE_DURATION(tmp),
> > + dsi->regs + VID_DPHY_TIME);
> > +
> > + /*
> > + * HSTX and LPRX timeouts are both expressed in TX byte clk cycles and
> > + * both should be set to at least the time it takes to transmit a
> > + * frame.
> > + */
> > + tmp = NSEC_PER_SEC / mode->vrefresh;
>
> vrefresh is a really rough approximation of the refresh. You may need
> some padding so that HSTX_TIMEOUT doesn't end up being just a little
> short of a frame. (Also, modes that userspace creates likely don't have
> the field initialized at all, so you'd need drm_mode_vrefresh() anyway)
Okay, I'll use drm_mode_vrefresh(), thanks for the hint.
>
> > + tmp /= tx_byte_period;
> > +
> > + for (div = 0; div <= CLK_DIV_MAX; div++) {
> > + if (tmp <= HSTX_TIMEOUT_MAX)
> > + break;
> > +
> > + tmp >>= 1;
> > + }
> > +
> > + if (tmp > HSTX_TIMEOUT_MAX)
> > + tmp = HSTX_TIMEOUT_MAX;
> > +
> > + writel(CLK_DIV(div) | HSTX_TIMEOUT(tmp),
> > + dsi->regs + MCTL_DPHY_TIMEOUT1);
> > +
> > + writel(LPRX_TIMEOUT(tmp), dsi->regs + MCTL_DPHY_TIMEOUT2);
> > +
> > + if (output->dev->mode_flags & MIPI_DSI_MODE_VIDEO) {
> > + switch (output->dev->format) {
> > + case MIPI_DSI_FMT_RGB888:
> > + tmp = VID_PIXEL_MODE_RGB888 |
> > + VID_DATATYPE(MIPI_DSI_PACKED_PIXEL_STREAM_24);
> > + break;
> > +
> > + case MIPI_DSI_FMT_RGB666:
> > + tmp = VID_PIXEL_MODE_RGB666 |
> > + VID_DATATYPE(MIPI_DSI_PIXEL_STREAM_3BYTE_18);
> > + break;
> > +
> > + case MIPI_DSI_FMT_RGB666_PACKED:
> > + tmp = VID_PIXEL_MODE_RGB666_PACKED |
> > + VID_DATATYPE(MIPI_DSI_PACKED_PIXEL_STREAM_18);
> > + break;
> > +
> > + case MIPI_DSI_FMT_RGB565:
> > + tmp = VID_PIXEL_MODE_RGB666_PACKED |
>
> I think you mean VID_PIXEL_MODE_RGB565?
I'll fix that as well.
>
> > + VID_DATATYPE(MIPI_DSI_PACKED_PIXEL_STREAM_16);
> > + break;
> > +
> > + default:
> > + dev_err(dsi->base.dev, "Unsupported DSI format\n");
> > + return;
> > + }
>
> > +static irqreturn_t cdns_dsi_interrupt(int irq, void *data)
> > +{
> > + struct cdns_dsi *dsi = data;
> > + irqreturn_t ret = IRQ_NONE;
> > + u32 flag, ctl;
> > +
> > + flag = readl(dsi->regs + DIRECT_CMD_STS_FLAG);
> > + if (flag) {
> > + ctl = readl(dsi->regs + DIRECT_CMD_STS_CTL);
> > + ctl &= ~flag;
> > + writel(ctl, dsi->regs + DIRECT_CMD_STS_CTL);
>
> Are you meant to just write flag to DIRECT_CMD_STS_CLEAR, maybe?
Actually, I want to keep the status flag untouched, I'm just masking the
interrupt to not be interrupted until the waiter has cleared the
status flags.
I'm doing that because the user may want to wait for several different
events (error, done, timeout, ...), and I'm not doing the check in the
interrupt handler. Instead, I'm just waking up the waiter and let him
check the status flag himself.
> Needing a RMW here seems odd.
>
> > + complete(&dsi->direct_cmd_comp);
> > + ret = IRQ_HANDLED;
> > + }
> > +
> > + return ret;
> > +}
Thanks for your review.
Boris
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
