Most of the q6v5-pil start function is same for the q6v5-wcss rproc
that will be added later. So split and move out the common pieces
so that the same code can be reused.
Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
---
drivers/remoteproc/qcom_q6v5_pil.c | 166 ++++++++++++++++++++-----------------
1 file changed, 91 insertions(+), 75 deletions(-)
diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c
index 5b5811d..19f453f 100644
--- a/drivers/remoteproc/qcom_q6v5_pil.c
+++ b/drivers/remoteproc/qcom_q6v5_pil.c
@@ -405,75 +405,107 @@ static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms)
return val;
}
-static int q6v5proc_reset(struct q6v5 *qproc)
+static int q6v5_reset(struct q6v5 *qproc)
{
- u32 val;
- int ret;
- int i;
+ u32 ret;
+ int val, i;
+ /* Assert resets, stop core */
+ val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
+ val |= Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE;
+ writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
- if (qproc->version == MSS_MSM8996) {
- /* Override the ACC value if required */
- writel(QDSP6SS_ACC_OVERRIDE_VAL,
- qproc->reg_base + QDSP6SS_STRAP_ACC);
+ /* BHS require xo cbcr to be enabled */
+ val = readl(qproc->reg_base + QDSP6SS_XO_CBCR);
+ val |= 0x1;
+ writel(val, qproc->reg_base + QDSP6SS_XO_CBCR);
- /* Assert resets, stop core */
- val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
- val |= Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE;
- writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+ /* Read CLKOFF bit to go low indicating CLK is enabled */
+ ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR,
+ val, !(val & BIT(31)), 1,
+ HALT_CHECK_MAX_LOOPS);
+ if (ret) {
+ dev_err(qproc->dev,
+ "xo cbcr enabling timed out (rc:%d)\n", ret);
+ return ret;
+ }
+ /* Enable power block headswitch and wait for it to stabilize */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= QDSP6v56_BHS_ON;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ udelay(1);
- /* BHS require xo cbcr to be enabled */
- val = readl(qproc->reg_base + QDSP6SS_XO_CBCR);
- val |= 0x1;
- writel(val, qproc->reg_base + QDSP6SS_XO_CBCR);
+ /* Put LDO in bypass mode */
+ val |= QDSP6v56_LDO_BYP;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- /* Read CLKOFF bit to go low indicating CLK is enabled */
- ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR,
- val, !(val & BIT(31)), 1,
- HALT_CHECK_MAX_LOOPS);
- if (ret) {
- dev_err(qproc->dev,
- "xo cbcr enabling timed out (rc:%d)\n", ret);
- return ret;
- }
- /* Enable power block headswitch and wait for it to stabilize */
- val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= QDSP6v56_BHS_ON;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ /* Deassert QDSP6 compiler memory clamp */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val &= ~QDSP6v56_CLAMP_QMC_MEM;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Deassert memory peripheral sleep and L2 memory standby */
+ val |= Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Turn on L1, L2, ETB and JU memories 1 at a time */
+ val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ for (i = 19; i >= 0; i--) {
+ val |= BIT(i);
+ writel(val, qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
+ /*
+ * Read back value to ensure the write is done then
+ * wait for 1us for both memory peripheral and data
+ * array to turn on.
+ */
+ val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
udelay(1);
+ }
+ /* Remove word line clamp */
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val &= ~QDSP6v56_CLAMP_WL;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- /* Put LDO in bypass mode */
- val |= QDSP6v56_LDO_BYP;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ return 0;
+}
- /* Deassert QDSP6 compiler memory clamp */
- val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val &= ~QDSP6v56_CLAMP_QMC_MEM;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+static void q6v5_reset_rest(struct q6v5 *qproc)
+{
+ u32 val;
- /* Deassert memory peripheral sleep and L2 memory standby */
- val |= Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- /* Turn on L1, L2, ETB and JU memories 1 at a time */
- val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
- for (i = 19; i >= 0; i--) {
- val |= BIT(i);
- writel(val, qproc->reg_base +
- QDSP6SS_MEM_PWR_CTL);
- /*
- * Read back value to ensure the write is done then
- * wait for 1us for both memory peripheral and data
- * array to turn on.
- */
- val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
- udelay(1);
- }
- /* Remove word line clamp */
- val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
- val &= ~QDSP6v56_CLAMP_WL;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+ /* Remove IO clamp */
+ val &= ~Q6SS_CLAMP_IO;
+ writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
+
+ /* Bring core out of reset */
+ val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
+ val &= ~Q6SS_CORE_ARES;
+ writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+
+ /* Turn on core clock */
+ val = readl(qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
+ val |= Q6SS_CLK_ENABLE;
+ writel(val, qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
+
+ /* Start core execution */
+ val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
+ val &= ~Q6SS_STOP_CORE;
+ writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+}
+
+static int q6v5proc_reset(struct q6v5 *qproc)
+{
+ u32 val;
+ int ret;
+
+ if (qproc->version == MSS_MSM8996) {
+ /* Override the ACC value if required */
+ writel(QDSP6SS_ACC_OVERRIDE_VAL,
+ qproc->reg_base + QDSP6SS_STRAP_ACC);
+ q6v5_reset(qproc);
} else {
/* Assert resets, stop core */
val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
@@ -501,24 +533,8 @@ static int q6v5proc_reset(struct q6v5 *qproc)
val |= Q6SS_L2DATA_SLP_NRET_N_0;
writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
}
- /* Remove IO clamp */
- val &= ~Q6SS_CLAMP_IO;
- writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
-
- /* Bring core out of reset */
- val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
- val &= ~Q6SS_CORE_ARES;
- writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
- /* Turn on core clock */
- val = readl(qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
- val |= Q6SS_CLK_ENABLE;
- writel(val, qproc->reg_base + QDSP6SS_GFMUX_CTL_REG);
-
- /* Start core execution */
- val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
- val &= ~Q6SS_STOP_CORE;
- writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
+ q6v5_reset_rest(qproc);
/* Wait for PBL status */
ret = q6v5_rmb_pbl_wait(qproc, 1000);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
