Add device-tree binding documentation SFP transceivers. Support for SFP
transceivers has been recently introduced (drivers/net/phy/sfp.c).
Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
---
v2:
Rename -gpio properties to -gpios
Rename the rate-select-gpio property to rate-select0-gpios
Add the rate-select1-gpios property
Add examples
---
Documentation/devicetree/bindings/net/sff,sfp.txt | 74 +++++++++++++++++++++++
1 file changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/sff,sfp.txt
diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt
new file mode 100644
index 000000000000..1d9c786d6287
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sff,sfp.txt
@@ -0,0 +1,74 @@
+Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
+Transceiver
+
+Required properties:
+
+- compatible : must be "sff,sfp"
+
+Optional Properties:
+
+- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
+ interface
+
+- moddef0-gpios : phandle of the MOD-DEF0 (AKA Mod_ABS) module presence input
+ gpio signal
+
+- los-gpios : phandle of the Receiver Loss of Signal Indication input gpio
+ signal
+
+- tx-fault-gpios : phandle of the Module Transmitter Fault input gpio signal
+
+- tx-disable-gpios : phandle of the Transmitter Disable output gpio signal
+
+- rate-select0-gpios : phandle of the Rx Signaling Rate Select (AKA RS0) output
+ gpio
+
+- rate-select1-gpios : phandle of the Tx Signaling Rate Select (AKA RS1) output
+ gpio (SFP+ only)
+
+Example #1: Direct serdes to SFP connection
+
+sfp_eth3: sfp-eth3 {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_1g_i2c>;
+ los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
+ moddef0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
+ tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
+};
+
+&cps_emac3 {
+ phy-mode = "sgmii";
+ phy-names = "comphy";
+ phys = <&cps_comphy 5 COMPHY_SGMII2>;
+ sfp = <&sfp_eth3>;
+};
+
+Example #2: Serdes to PHY to SFP connection
+
+sfp_eth0: sfp-eth0 {
+ compatible = "sff,sfp+";
+ i2c-bus = <&sfpp0_i2c>;
+ los-gpio = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
+ moddef0-gpio = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cps_sfpp0_pins>;
+ tx-disable-gpio = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
+};
+
+p0_phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
+ reg = <0>;
+ interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
+ sfp = <&sfp_eth0>;
+};
+
+&cpm_eth0 {
+ phy = <&p0_phy>;
+ phy-mode = "10gbase-kr";
+};
--
2.14.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
