Re: [PATCH v3] phy: Add new Exynos5 USB 3.0 PHY driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Jan 20, 2014 at 7:12 PM, Vivek Gautam <gautam.vivek@xxxxxxxxxxx> wrote:
> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
> The new driver uses the generic PHY framework and will interact
> with DWC3 controller present on Exynos5 series of SoCs.
> Thereby, removing old phy-samsung-usb3 driver and related code
> used untill now which was based on usb/phy framework.
>
> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>

Sorry, forgot to add a Reviewed-by tag from Felipe. :-(
Will update in the next version of patch after getting a feedback on this patch.

> ---
>
> Changes from v2:
> 1) Added support for multiple PHYs (UTMI+ and PIPE3) and
>    related changes in the driver structuring.
> 2) Added a xlate function to get the required phy out of
>    number of PHYs in mutiple PHY scenerio.
> 3) Changed the names of few structures and variables to
>    have a clearer meaning.
> 4) Added 'usb3phy_config' structure to take care of mutiple
>    phys for a SoC having 'exynos5_usb3phy_drv_data' driver data.
> 5) Not deleting support for old driver 'phy-samsung-usb3' until
>    required support for generic phy is added to DWC3.
>
>  .../devicetree/bindings/phy/samsung-phy.txt        |   49 ++
>  drivers/phy/Kconfig                                |    8 +
>  drivers/phy/Makefile                               |    1 +
>  drivers/phy/phy-exynos5-usb3.c                     |  621 ++++++++++++++++++++
>  4 files changed, 679 insertions(+)
>  create mode 100644 drivers/phy/phy-exynos5-usb3.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index c0fccaa..57079f8 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -20,3 +20,52 @@ Required properties:
>  - compatible : should be "samsung,exynos5250-dp-video-phy";
>  - reg : offset and length of the Display Port PHY register set;
>  - #phy-cells : from the generic PHY bindings, must be 0;
> +
> +Samsung Exynos5 SoC series USB 3.0 PHY controller
> +--------------------------------------------------
> +
> +Required properties:
> +- compatible : Should be set to one of the following supported values:
> +       - "samsung,exynos5250-usb3phy" - for exynos5250 SoC,
> +       - "samsung,exynos5420-usb3phy" - for exynos5420 SoC.
> +- reg : Register offset and length of USB 3.0 PHY register set;
> +- clocks: Clock IDs array as required by the controller
> +- clock-names: names of clocks correseponding to IDs in the clock property;
> +       Required clocks:
> +       - phy: main PHY clock (same as USB 3.0 controller IP clock),
> +               used for register access.
> +       - usb3phy_refclk: PHY's reference clock (usually crystal clock),
> +               associated by phy name, used to determine bit values for
> +               clock settings register.
> +       Additional clock required for Exynos5420:
> +       - usb30_sclk_100m: Additional special clock used for PHY operation
> +                          depicted as 'sclk_usbphy30' in CMU of Exynos5420.
> +- samsung,syscon-phandle: phandle for syscon interface, which is used to
> +       control pmu registers for power isolation.
> +- #phy-cells : from the generic PHY bindings, must be 1;
> +
> +For "samsung,exynos5250-usb3phy" and "samsung,exynos5420-usb3phy" compatible
> +PHYs, the second cell in the PHY specifier identifies the PHY id, which is
> +interpreted as follows:
> +  0 - UTMI+ type phy,
> +  1 - PIPE3 type phy,
> +
> +Example:
> +       usb3_phy: usbphy@12100000 {
> +               compatible = "samsung,exynos5250-usb3phy";
> +               reg = <0x12100000 0x100>;
> +               clocks = <&clock 286>, <&clock 1>;
> +               clock-names = "phy", "usb3phy_refclk";
> +               samsung,syscon-phandle = <&pmu_syscon>;
> +               #phy-cells = <1>;
> +       };
> +
> +- aliases: For SoCs like Exynos5420 having multiple USB PHY controllers,
> +          'usb3_phy' nodes should have numbered alias in the aliases node,
> +          in the form of usb3phyN, N = 0, 1... (depending on number of
> +          controllers).
> +Example:
> +       aliases {
> +               usb3phy0 = &usb3_phy0;
> +               usb3phy1 = &usb3_phy1;
> +       };
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 330ef2d..32f9f38 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -51,4 +51,12 @@ config PHY_EXYNOS_DP_VIDEO
>         help
>           Support for Display Port PHY found on Samsung EXYNOS SoCs.
>
> +config PHY_EXYNOS5_USB3
> +       tristate "Exynos5 SoC series USB 3.0 PHY driver"
> +       depends on ARCH_EXYNOS5
> +       select GENERIC_PHY
> +       select MFD_SYSCON
> +       help
> +         Enable USB 3.0 PHY support for Exynos 5 SoC series
> +
>  endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index d0caae9..9c06a61 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -7,3 +7,4 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)       += phy-exynos-dp-video.o
>  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)    += phy-exynos-mipi-video.o
>  obj-$(CONFIG_OMAP_USB2)                        += phy-omap-usb2.o
>  obj-$(CONFIG_TWL4030_USB)              += phy-twl4030-usb.o
> +obj-$(CONFIG_PHY_EXYNOS5_USB3)         += phy-exynos5-usb3.o
> diff --git a/drivers/phy/phy-exynos5-usb3.c b/drivers/phy/phy-exynos5-usb3.c
> new file mode 100644
> index 0000000..24efed0
> --- /dev/null
> +++ b/drivers/phy/phy-exynos5-usb3.c
> @@ -0,0 +1,621 @@
> +/*
> + * Samsung EXYNOS5 SoC series USB 3.0 PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/mutex.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +
> +/* Exynos USB PHY registers */
> +#define EXYNOS5_FSEL_9MHZ6             0x0
> +#define EXYNOS5_FSEL_10MHZ             0x1
> +#define EXYNOS5_FSEL_12MHZ             0x2
> +#define EXYNOS5_FSEL_19MHZ2            0x3
> +#define EXYNOS5_FSEL_20MHZ             0x4
> +#define EXYNOS5_FSEL_24MHZ             0x5
> +#define EXYNOS5_FSEL_50MHZ             0x7
> +
> +/* EXYNOS5: USB 3.0 DRD PHY registers */
> +#define EXYNOS5_DRD_LINKSYSTEM                 (0x04)
> +
> +#define LINKSYSTEM_FLADJ_MASK                  (0x3f << 1)
> +#define LINKSYSTEM_FLADJ(_x)                   ((_x) << 1)
> +#define LINKSYSTEM_XHCI_VERSION_CONTROL                (0x1 << 27)
> +
> +#define EXYNOS5_DRD_PHYUTMI                    (0x08)
> +
> +#define PHYUTMI_OTGDISABLE                     (0x1 << 6)
> +#define PHYUTMI_FORCESUSPEND                   (0x1 << 1)
> +#define PHYUTMI_FORCESLEEP                     (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYPIPE                    (0x0c)
> +
> +#define EXYNOS5_DRD_PHYCLKRST                  (0x10)
> +
> +#define PHYCLKRST_EN_UTMISUSPEND               (0x1 << 31)
> +
> +#define PHYCLKRST_SSC_REFCLKSEL_MASK           (0xff << 23)
> +#define PHYCLKRST_SSC_REFCLKSEL(_x)            ((_x) << 23)
> +
> +#define PHYCLKRST_SSC_RANGE_MASK               (0x03 << 21)
> +#define PHYCLKRST_SSC_RANGE(_x)                        ((_x) << 21)
> +
> +#define PHYCLKRST_SSC_EN                       (0x1 << 20)
> +#define PHYCLKRST_REF_SSP_EN                   (0x1 << 19)
> +#define PHYCLKRST_REF_CLKDIV2                  (0x1 << 18)
> +
> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK         (0x7f << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF   (0x19 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF      (0x32 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF    (0x68 << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF    (0x7d << 11)
> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
> +
> +#define PHYCLKRST_FSEL_MASK                    (0x3f << 5)
> +#define PHYCLKRST_FSEL(_x)                     ((_x) << 5)
> +#define PHYCLKRST_FSEL_PAD_100MHZ              (0x27 << 5)
> +#define PHYCLKRST_FSEL_PAD_24MHZ               (0x2a << 5)
> +#define PHYCLKRST_FSEL_PAD_20MHZ               (0x31 << 5)
> +#define PHYCLKRST_FSEL_PAD_19_2MHZ             (0x38 << 5)
> +
> +#define PHYCLKRST_RETENABLEN                   (0x1 << 4)
> +
> +#define PHYCLKRST_REFCLKSEL_MASK               (0x03 << 2)
> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK         (0x2 << 2)
> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK         (0x3 << 2)
> +
> +#define PHYCLKRST_PORTRESET                    (0x1 << 1)
> +#define PHYCLKRST_COMMONONN                    (0x1 << 0)
> +
> +#define EXYNOS5_DRD_PHYREG0                    (0x14)
> +#define EXYNOS5_DRD_PHYREG1                    (0x18)
> +
> +#define EXYNOS5_DRD_PHYPARAM0                  (0x1c)
> +
> +#define PHYPARAM0_REF_USE_PAD                  (0x1 << 31)
> +#define PHYPARAM0_REF_LOSLEVEL_MASK            (0x1f << 26)
> +#define PHYPARAM0_REF_LOSLEVEL                 (0x9 << 26)
> +
> +#define EXYNOS5_DRD_PHYPARAM1                  (0x20)
> +
> +#define PHYPARAM1_PCS_TXDEEMPH_MASK            (0x1f << 0)
> +#define PHYPARAM1_PCS_TXDEEMPH                 (0x1c)
> +
> +#define EXYNOS5_DRD_PHYTERM                    (0x24)
> +
> +#define EXYNOS5_DRD_PHYTEST                    (0x28)
> +
> +#define PHYTEST_POWERDOWN_SSP                  (0x1 << 3)
> +#define PHYTEST_POWERDOWN_HSP                  (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYADP                     (0x2c)
> +
> +#define EXYNOS5_DRD_PHYBATCHG                  (0x30)
> +
> +#define PHYBATCHG_UTMI_CLKSEL                  (0x1 << 2)
> +
> +#define EXYNOS5_DRD_PHYRESUME                  (0x34)
> +#define EXYNOS5_DRD_LINKPORT                   (0x44)
> +
> +/* Power isolation defined in power management unit */
> +#define EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET     (0x704)
> +#define EXYNOS5_USB3DRD_PMU_ISOL               (1 << 0)
> +
> +#define KHZ    1000
> +#define MHZ    (KHZ * KHZ)
> +
> +enum exynos5_usb3phy_id {
> +       EXYNOS5_USB3PHY_UTMI,
> +       EXYNOS5_USB3PHY_PIPE3,
> +       EXYNOS5_USB3PHYS_NUM,
> +};
> +
> +struct usb3phy_config {
> +       u32 id;
> +       u32 reg_pmu_offset;
> +       void (*phy_isol)(struct phy *phy, u32 on);
> +};
> +
> +struct exynos5_usb3phy_drv_data {
> +       bool has_usb30_sclk;
> +       bool has_multi_controller;
> +       const struct usb3phy_config *phy_cfg;
> +};
> +
> +/**
> + * struct exynos5_usb3phy_driver - driver data for USB 3.0 PHY
> + * @dev: pointer to device instance of this platform device
> + * @reg_phy: usb phy controller register memory base
> + * @clk: phy clock for register access
> + * @usb30_sclk: additional special clock for phy operations
> + * @drv_data: pointer to SoC level driver data structure
> + * @phys[]: array for 'EXYNOS5_USB3PHYS_NUM' number of PHY
> + *         instances each with its 'phy' and 'phy_cfg'.
> + * @extrefclk: frequency select settings when using 'separate
> + *            reference clocks' for SS and HS operations
> + * @rate: rate of reference clock to PHY block
> + * @channel: number of PHY channels present in SoC
> + */
> +struct exynos5_usb3phy_driver {
> +       struct device *dev;
> +       void __iomem *reg_phy;
> +       struct clk *clk;
> +       struct clk *usb30_sclk;
> +       const struct exynos5_usb3phy_drv_data *drv_data;
> +       struct phy_usb_instance {
> +               struct phy *phy;
> +               u32 index;
> +               struct regmap *reg_isol;
> +               const struct usb3phy_config *phy_cfg;
> +       } phys[EXYNOS5_USB3PHYS_NUM];
> +       u32 extrefclk;
> +       unsigned long rate;
> +       u32 channel;
> +};
> +
> +#define to_usb3phy_driver(inst) \
> +       container_of((inst), struct exynos5_usb3phy_driver, \
> +                    phys[(inst)->index]);
> +
> +/*
> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
> + * can be written to the phy register.
> + */
> +static u32 exynos5_rate_to_clk(unsigned long rate)
> +{
> +       unsigned int clksel;
> +
> +       /* EXYNOS5_FSEL_MASK */
> +
> +       switch (rate) {
> +       case 9600 * KHZ:
> +               clksel = EXYNOS5_FSEL_9MHZ6;
> +               break;
> +       case 10 * MHZ:
> +               clksel = EXYNOS5_FSEL_10MHZ;
> +               break;
> +       case 12 * MHZ:
> +               clksel = EXYNOS5_FSEL_12MHZ;
> +               break;
> +       case 19200 * KHZ:
> +               clksel = EXYNOS5_FSEL_19MHZ2;
> +               break;
> +       case 20 * MHZ:
> +               clksel = EXYNOS5_FSEL_20MHZ;
> +               break;
> +       case 24 * MHZ:
> +               clksel = EXYNOS5_FSEL_24MHZ;
> +               break;
> +       case 50 * MHZ:
> +               clksel = EXYNOS5_FSEL_50MHZ;
> +               break;
> +       default:
> +               clksel = -EINVAL;
> +       }
> +
> +       return clksel;
> +}
> +
> +static void exynos5_usb3phy_isol(struct phy *phy, unsigned int on)
> +{
> +       u32 pmu_offset;
> +       struct phy_usb_instance *inst = phy_get_drvdata(phy);
> +       struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> +       pmu_offset = inst->phy_cfg->reg_pmu_offset;
> +       if (!inst->reg_isol)
> +               return;
> +
> +       switch (drv->channel) {
> +       case 1:
> +               /* Channel 1 is at 0x708 offset */
> +               pmu_offset += sizeof(&pmu_offset);
> +               break;
> +       case 0:
> +       default:
> +               /* Channel 0 is at 0x704 offset */
> +               break;
> +       }
> +
> +       regmap_update_bits(inst->reg_isol, pmu_offset,
> +                          EXYNOS5_USB3DRD_PMU_ISOL, ~on);
> +}
> +
> +/*
> + * Sets the phy clk as EXTREFCLK (XXTI) which is internal clock from clock core.
> + */
> +static u32 exynos5_usb3phy_set_refclk(struct exynos5_usb3phy_driver *drv)
> +{
> +       u32 reg;
> +
> +       reg = PHYCLKRST_REFCLKSEL_EXT_REFCLK |
> +             PHYCLKRST_FSEL(drv->extrefclk);
> +
> +       switch (drv->extrefclk) {
> +       case EXYNOS5_FSEL_50MHZ:
> +               reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
> +                       PHYCLKRST_SSC_REFCLKSEL(0x00));
> +               break;
> +       case EXYNOS5_FSEL_24MHZ:
> +               reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
> +                       PHYCLKRST_SSC_REFCLKSEL(0x88));
> +               break;
> +       case EXYNOS5_FSEL_20MHZ:
> +               reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
> +                       PHYCLKRST_SSC_REFCLKSEL(0x00));
> +               break;
> +       case EXYNOS5_FSEL_19MHZ2:
> +               reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
> +                       PHYCLKRST_SSC_REFCLKSEL(0x88));
> +               break;
> +       default:
> +               dev_dbg(drv->dev, "unsupported ref clk\n");
> +               break;
> +       }
> +
> +       return reg;
> +}
> +
> +static int exynos5_usb3phy_init(struct phy *phy)
> +{
> +       int ret;
> +       u32 phyparam0;
> +       u32 phyparam1;
> +       u32 linksystem;
> +       u32 phybatchg;
> +       u32 phytest;
> +       u32 phyclkrst;
> +       struct phy_usb_instance *inst = phy_get_drvdata(phy);
> +       struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> +       ret = clk_prepare_enable(drv->clk);
> +       if (ret)
> +               return ret;
> +
> +       drv->extrefclk = exynos5_rate_to_clk(drv->rate);
> +       if (drv->extrefclk == -EINVAL) {
> +               dev_err(drv->dev, "Clock rate (%ld) not supported\n",
> +                                               drv->rate);
> +               return -EINVAL;
> +       }
> +
> +       /* Reset USB 3.0 PHY */
> +       writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYREG0);
> +
> +       phyparam0 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +       /* Select PHY CLK source */
> +       phyparam0 &= ~PHYPARAM0_REF_USE_PAD;
> +       /* Set Loss-of-Signal Detector sensitivity */
> +       phyparam0 &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
> +       phyparam0 |= PHYPARAM0_REF_LOSLEVEL;
> +       writel(phyparam0, drv->reg_phy + EXYNOS5_DRD_PHYPARAM0);
> +
> +       writel(0x0, drv->reg_phy + EXYNOS5_DRD_PHYRESUME);
> +
> +       /*
> +        * Setting the Frame length Adj value[6:1] to default 0x20
> +        * See xHCI 1.0 spec, 5.2.4
> +        */
> +       linksystem = LINKSYSTEM_XHCI_VERSION_CONTROL |
> +                    LINKSYSTEM_FLADJ(0x20);
> +       writel(linksystem, drv->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
> +
> +       phyparam1 = readl(drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +       /* Set Tx De-Emphasis level */
> +       phyparam1 &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
> +       phyparam1 |= PHYPARAM1_PCS_TXDEEMPH;
> +       writel(phyparam1, drv->reg_phy + EXYNOS5_DRD_PHYPARAM1);
> +
> +       phybatchg = readl(drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +       phybatchg |= PHYBATCHG_UTMI_CLKSEL;
> +       writel(phybatchg, drv->reg_phy + EXYNOS5_DRD_PHYBATCHG);
> +
> +       /* PHYTEST POWERDOWN Control */
> +       phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +       phytest &= ~(PHYTEST_POWERDOWN_SSP |
> +                    PHYTEST_POWERDOWN_HSP);
> +       writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> +       /* UTMI Power Control */
> +       writel(PHYUTMI_OTGDISABLE, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> +       phyclkrst = exynos5_usb3phy_set_refclk(drv);
> +
> +       phyclkrst |= PHYCLKRST_PORTRESET |
> +                    /* Digital power supply in normal operating mode */
> +                    PHYCLKRST_RETENABLEN |
> +                    /* Enable ref clock for SS function */
> +                    PHYCLKRST_REF_SSP_EN |
> +                    /* Enable spread spectrum */
> +                    PHYCLKRST_SSC_EN |
> +                    /* Power down HS Bias and PLL blocks in suspend mode */
> +                    PHYCLKRST_COMMONONN;
> +
> +       writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> +       udelay(10);
> +
> +       phyclkrst &= ~PHYCLKRST_PORTRESET;
> +       writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> +       clk_disable_unprepare(drv->clk);
> +
> +       return 0;
> +}
> +
> +static int exynos5_usb3phy_exit(struct phy *phy)
> +{
> +       int ret;
> +       u32 phyutmi;
> +       u32 phyclkrst;
> +       u32 phytest;
> +       struct phy_usb_instance *inst = phy_get_drvdata(phy);
> +       struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> +       ret = clk_prepare_enable(drv->clk);
> +       if (ret)
> +               return ret;
> +
> +       phyutmi = PHYUTMI_OTGDISABLE |
> +                 PHYUTMI_FORCESUSPEND |
> +                 PHYUTMI_FORCESLEEP;
> +       writel(phyutmi, drv->reg_phy + EXYNOS5_DRD_PHYUTMI);
> +
> +       /* Resetting the PHYCLKRST enable bits to reduce leakage current */
> +       phyclkrst = readl(drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +       phyclkrst &= ~(PHYCLKRST_REF_SSP_EN |
> +                      PHYCLKRST_SSC_EN |
> +                      PHYCLKRST_COMMONONN);
> +       writel(phyclkrst, drv->reg_phy + EXYNOS5_DRD_PHYCLKRST);
> +
> +       /* Control PHYTEST to remove leakage current */
> +       phytest = readl(drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +       phytest |= PHYTEST_POWERDOWN_SSP |
> +                  PHYTEST_POWERDOWN_HSP;
> +       writel(phytest, drv->reg_phy + EXYNOS5_DRD_PHYTEST);
> +
> +       clk_disable_unprepare(drv->clk);
> +
> +       return 0;
> +}
> +
> +static int exynos5_usb3phy_power_on(struct phy *phy)
> +{
> +       struct phy_usb_instance *inst = phy_get_drvdata(phy);
> +       struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> +       dev_dbg(drv->dev, "Request to power_on usb3drd phy\n");
> +
> +       if (!IS_ERR(drv->usb30_sclk))
> +               clk_prepare_enable(drv->usb30_sclk);
> +
> +       /* Power-on PHY*/
> +       inst->phy_cfg->phy_isol(phy, 0);
> +
> +       return 0;
> +}
> +
> +static int exynos5_usb3phy_power_off(struct phy *phy)
> +{
> +       struct phy_usb_instance *inst = phy_get_drvdata(phy);
> +       struct exynos5_usb3phy_driver *drv = to_usb3phy_driver(inst);
> +
> +       dev_dbg(drv->dev, "Request to power_off usb3drd phy\n");
> +
> +       /* Power-off the PHY */
> +       inst->phy_cfg->phy_isol(phy, 1);
> +
> +       if (!IS_ERR(drv->usb30_sclk))
> +               clk_disable_unprepare(drv->usb30_sclk);
> +
> +       return 0;
> +}
> +
> +static struct phy *exynos5_usb3phy_xlate(struct device *dev,
> +                                       struct of_phandle_args *args)
> +{
> +       struct exynos5_usb3phy_driver *drv = dev_get_drvdata(dev);
> +
> +       if (WARN_ON(args->args[0] > EXYNOS5_USB3PHYS_NUM))
> +               return ERR_PTR(-ENODEV);
> +
> +       return drv->phys[args->args[0]].phy;
> +}
> +
> +static struct phy_ops exynos5_usb3phy_ops = {
> +       .init           = exynos5_usb3phy_init,
> +       .exit           = exynos5_usb3phy_exit,
> +       .power_on       = exynos5_usb3phy_power_on,
> +       .power_off      = exynos5_usb3phy_power_off,
> +       .owner          = THIS_MODULE,
> +};
> +
> +const struct usb3phy_config exynos5_usb3phy_cfg[] = {
> +       {
> +               .id             = EXYNOS5_USB3PHY_UTMI,
> +               .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> +               .phy_isol       = exynos5_usb3phy_isol,
> +       },
> +       {
> +               .id             = EXYNOS5_USB3PHY_PIPE3,
> +               .reg_pmu_offset = EXYNOS5_USB3DRD_PHY_PMU_REG_OFFSET,
> +               .phy_isol       = exynos5_usb3phy_isol,
> +       },
> +       {},
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5420_usb3phy = {
> +       .has_usb30_sclk         = true,
> +       .has_multi_controller   = true,
> +       .phy_cfg                = exynos5_usb3phy_cfg,
> +};
> +
> +const struct exynos5_usb3phy_drv_data exynos5250_usb3phy = {
> +       .has_usb30_sclk         = false,
> +       .has_multi_controller   = false,
> +       .phy_cfg                = exynos5_usb3phy_cfg,
> +};
> +
> +static const struct of_device_id exynos5_usb3phy_of_match[] = {
> +       {
> +               .compatible = "samsung,exynos5250-usb3phy",
> +               .data = &exynos5250_usb3phy
> +       }, {
> +               .compatible = "samsung,exynos5420-usb3phy",
> +               .data = &exynos5420_usb3phy
> +       },
> +       { },
> +};
> +
> +static int exynos5_usb3phy_probe(struct platform_device *pdev)
> +{
> +       struct device *dev = &pdev->dev;
> +       struct device_node *node = dev->of_node;
> +       struct exynos5_usb3phy_driver *drv;
> +       struct phy_provider *phy_provider;
> +       struct resource *res;
> +       struct clk *clk;
> +       const struct of_device_id *match;
> +       const struct exynos5_usb3phy_drv_data *drv_data;
> +       struct regmap *reg_isol;
> +       int i;
> +
> +       /*
> +        * Exynos systems are completely DT enabled,
> +        * so lets not have any platform data support for this driver.
> +        */
> +       if (!node) {
> +               dev_err(dev, "no device node found\n");
> +               return -ENODEV;
> +       }
> +
> +       match = of_match_node(exynos5_usb3phy_of_match, pdev->dev.of_node);
> +       if (!match) {
> +               dev_err(dev, "of_match_node() failed\n");
> +               return -EINVAL;
> +       }
> +       drv_data = match->data;
> +
> +       drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
> +       if (!drv) {
> +               dev_err(dev, "Failed to allocate memory\n");
> +               return -ENOMEM;
> +       }
> +
> +       dev_set_drvdata(dev, drv);
> +       drv->dev = dev;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       drv->reg_phy = devm_ioremap_resource(dev, res);
> +       if (IS_ERR(drv->reg_phy)) {
> +               dev_err(dev, "Failed to map register memory (phy)\n");
> +               return PTR_ERR(drv->reg_phy);
> +       }
> +
> +       drv->drv_data = drv_data;
> +
> +       /*
> +        * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
> +        * each having separate power control registers.
> +        * 'drv->channel' facilitates to set such registers.
> +        */
> +       if (drv->drv_data->has_multi_controller) {
> +               drv->channel = of_alias_get_id(node, "usb3phy");
> +               if (drv->channel < 0) {
> +                       dev_err(dev, "Invalid usb3drd phy node\n");
> +                       return -EINVAL;
> +               }
> +       }
> +
> +       drv->clk = devm_clk_get(dev, "phy");
> +       if (IS_ERR(drv->clk)) {
> +               dev_err(dev, "Failed to get clock of phy controller\n");
> +               return PTR_ERR(drv->clk);
> +       }
> +
> +       /*
> +        * Exysno5420 SoC has an additional special clock, used for
> +        * for USB 3.0 PHY operation, this clock goes to the PHY block
> +        * as a reference clock to clock generation block of the controller,
> +        * named as 'USB30_SCLK_100M'.
> +        */
> +       if (drv_data->has_usb30_sclk) {
> +               drv->usb30_sclk = devm_clk_get(dev, "usb30_sclk_100m");
> +               if (IS_ERR(drv->usb30_sclk)) {
> +                       dev_err(dev, "Failed to get phy reference clock\n");
> +                       return PTR_ERR(drv->usb30_sclk);
> +               }
> +       }
> +
> +       clk = clk_get(dev, "usb3phy_refclk");
> +       if (IS_ERR(clk)) {
> +               dev_err(dev, "Failed to get reference clock of usb3drd phy\n");
> +               return PTR_ERR(clk);
> +       }
> +       drv->rate = clk_get_rate(clk);
> +       clk_put(clk);
> +
> +       dev_dbg(dev, "Creating usb3drd phy\n");
> +
> +       reg_isol = syscon_regmap_lookup_by_phandle(dev->of_node,
> +                                                  "samsung,syscon-phandle");
> +       if (IS_ERR(reg_isol)) {
> +               dev_err(dev, "Failed to map register memory (isolation)\n");
> +               return PTR_ERR(reg_isol);
> +       }
> +
> +       for (i = 0; i < EXYNOS5_USB3PHYS_NUM; i++) {
> +               struct phy *phy = devm_phy_create(dev, &exynos5_usb3phy_ops,
> +                                                 NULL);
> +               if (IS_ERR(phy)) {
> +                       dev_err(dev, "Failed to create usb3drd phy\n");
> +                       return PTR_ERR(phy);
> +               }
> +
> +               drv->phys[i].phy = phy;
> +               drv->phys[i].index = i;
> +               drv->phys[i].reg_isol = reg_isol;
> +               drv->phys[i].phy_cfg = &drv_data->phy_cfg[i];
> +               phy_set_drvdata(phy, &drv->phys[i]);
> +       }
> +
> +       phy_provider = devm_of_phy_provider_register(dev,
> +                                                    exynos5_usb3phy_xlate);
> +       if (IS_ERR(phy_provider)) {
> +               dev_err(drv->dev, "Failed to register phy provider\n");
> +               return PTR_ERR(phy_provider);
> +       }
> +
> +       return 0;
> +}
> +
> +static struct platform_driver exynos5_usb3phy_driver = {
> +       .probe  = exynos5_usb3phy_probe,
> +       .driver = {
> +               .of_match_table = exynos5_usb3phy_of_match,
> +               .name           = "exynos5-usb3phy",
> +               .owner          = THIS_MODULE,
> +       }
> +};
> +
> +module_platform_driver(exynos5_usb3phy_driver);
> +MODULE_DESCRIPTION("Samsung EXYNOS5 series SoC USB 3.0 PHY driver");
> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:exynos5-usb3phy");
> --
> 1.7.10.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html



-- 
Best Regards
Vivek Gautam
Samsung R&D Institute, Bangalore
India
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux