On 07/21/2017 05:06 PM, Varadarajan Narayanan wrote:
Presently, the phy pipe clock's name is assumed to be either
usb3_phy_pipe_clk_src or pcie_XX_pipe_clk_src (where XX is the
phy lane's number). However, this will not work if an SoC has
more than one instance of the phy. Hence, instead of assuming
the name of the clock, fetch it from the DT.
Signed-off-by: Varadarajan Narayanan <varada@xxxxxxxxxxxxxx>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 45 +++++++++++++++++++++++--------------
1 file changed, 28 insertions(+), 17 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 78ca628..b046866 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -925,20 +925,13 @@ static int qcom_qmp_phy_clk_init(struct device *dev)
* clk | +-------+ | +-----+
* +---------------+
*/
-static int phy_pipe_clk_register(struct qcom_qmp *qmp, int id)
+static int phy_pipe_clk_register(struct qcom_qmp *qmp, const char *clk_name)
{
- char name[24];
struct clk_fixed_rate *fixed;
struct clk_init_data init = { };
- switch (qmp->cfg->type) {
- case PHY_TYPE_USB3:
- snprintf(name, sizeof(name), "usb3_phy_pipe_clk_src");
- break;
- case PHY_TYPE_PCIE:
- snprintf(name, sizeof(name), "pcie_%d_pipe_clk_src", id);
- break;
- default:
+ if ((qmp->cfg->type != PHY_TYPE_USB3) &&
+ (qmp->cfg->type != PHY_TYPE_PCIE)) {
/* not all phys register pipe clocks, so return success */
return 0;
}
@@ -947,7 +940,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, int id)
if (!fixed)
return -ENOMEM;
- init.name = name;
+ init.name = clk_name;
init.ops = &clk_fixed_rate_ops;
/* controllers using QMP phys use 125MHz pipe clock interface */
@@ -1110,6 +1103,8 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
id = 0;
for_each_available_child_of_node(dev->of_node, child) {
+ const char *clk_name;
+
/* Create per-lane phy */
ret = qcom_qmp_phy_create(dev, child, id);
if (ret) {
@@ -1119,15 +1114,31 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
}
/*
- * Register the pipe clock provided by phy.
- * See function description to see details of this pipe clock.
+ * This property is mandatory only for PCIe/USB phys.
+ * For other phy types don't return failure.
*/
- ret = phy_pipe_clk_register(qmp, id);
- if (ret) {
- dev_err(qmp->dev,
- "failed to register pipe clock source\n");
+ ret = of_property_read_string(child, "clock-output-names",
+ &clk_name);
+ if (ret && (qmp->cfg->type == PHY_TYPE_PCIE ||
+ qmp->cfg->type == PHY_TYPE_USB3)) {
Let's not check the phy type twice. Once here and once again in the
phy_pipe_clk_register().
May be we can move this property read in phy_pipe_clk_registe() itself.
That way you can avoid passing the clk_name also. WDUT?
Regards
Vivek
+ dev_err(dev,
+ "failed to get clock-output-names for lane%d phy, %d\n",
+ id, ret);
return ret;
}
+
+ if (!ret) {
+ /*
+ * Register the pipe clock provided by phy. See function
+ * description to see details of this pipe clock.
+ */
+ ret = phy_pipe_clk_register(qmp, clk_name);
+ if (ret) {
+ dev_err(qmp->dev,
+ "failed to register pipe clock source\n");
+ return ret;
+ }
+ }
id++;
}
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html