On Mon, 2017-07-24 at 20:20 +0200, Martin Blumenstingl wrote: > On Mon, Jul 24, 2017 at 6:09 PM, Jerome Brunet <jbrunet@xxxxxxxxxxxx> wrote: > > On Mon, 2017-07-24 at 14:26 +0200, Neil Armstrong wrote: > > > On 07/24/2017 02:06 PM, Neil Armstrong wrote: > > > > On 07/23/2017 07:03 PM, Joseph Kogut wrote: > > > > > Hi Kevin, > > > > > > > > > > I tested on a P212 reference board, which is currently the only GXL > > > > > based board I have. > > > > > > > > > > Before applying the patch, high activity on the ethernet interface > > > > > would cause the link to break, requiring the interface to be brought > > > > > down and back up before it would work again. After applying the patch, > > > > > I could not get the link to break with any transfers. > > > > > > > > > > _______________________________________________ > > > > > linux-arm-kernel mailing list > > > > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > > > > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > > > > > > > > > > > > > Hi Joseph, > > > > > > > > [please keep the history of the conversation when replying] > > > > > > > > Is it a original P212 board, or a board based on the P212 ref design ? > > > > > > > > I'm currently testing the v4.13-rc2 on the official P212 board we > > > > received > > > > from Amlogic > > > > and using iperf3 in both directions, I have an issue after a few minutes > > > > running iperf3 with : > > > > > > > > # while true ; do iperf3 -c 192.168.1.21 ; iperf3 -c 192.168.1.21 -R ; > > > > done > > > > > > > > That cycles between the two iperf directions. > > > > > > > > After a few minutes, it stalls with : > > > > > > > > Connecting to host 192.168.1.21, port 5201 > > > > [ 4] local 192.168.1.183 port 51286 connected to 192.168.1.21 port 5201 > > > > [ ID] Interval Transfer Bandwidth Retr Cwnd > > > > [ 4] 0.00-1.00 sec 1.64 MBytes 13.7 Mbits/sec 2 1.41 KBytes > > > > [ 4] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes > > > > [ 4] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes > > > > [ 4] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes > > > > [ 4] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes > > > > [ 4] 5.00-6.00 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes > > > > [ 4] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 1 1.41 KBytes > > > > [ 4] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes > > > > [ 4] 8.00-9.00 sec 0.00 Bytes 0.00 bits/sec 0 1.41 KBytes > > > > > > > > Same kind of test shows no issue on the libretech-cc and the khadas-vim > > In this case, I don't think meson-gxl.dtsi is where you should make your > > change. ahahah, silly me ! I forgot that it was 100MBps PHY. tx delay makes no sense here, 2ns delay would not make much difference on a 25MHz clock Sorry for the confusion > > > > > > > > > > And then, after: > > > > # ifconfig eth0 down > > > > # ifconfig eth0 up > > > > > > > > It cycles between : > > > > [ 1483.009919] meson8b-dwmac c9410000.ethernet eth0: Link is Up - > > > > 100Mbps/Full - flow control rx/tx > > > > [ 1487.105725] meson8b-dwmac c9410000.ethernet eth0: Link is Down > > > > [ 1490.177943] meson8b-dwmac c9410000.ethernet eth0: Link is Up - > > > > 100Mbps/Full - flow control rx/tx > > > > [ 1494.273713] meson8b-dwmac c9410000.ethernet eth0: Link is Down > > > > This does not look like the issue we had on the odroid-c2. > > However, I have seen behavior like this (link down/up flickering) when the > > rgmii > > delays are way off. > > > > Maybe you could try playing with "amlogic,tx-delay-ns" property ? > > we need to change dwmac-meson8b.c so it applies the TX delay also for > RMII PHYs. currently the TX delay is always set to 0 for RMII PHYs, > see: [0] > > > > > > > > > and so on. > > > > > > > > And this patch does not fix this at all. > > > > > > > > It seems to be more a PHY driver issue here. > > > > > > > > Could you share the results with the same command ? > > > > > > > > Neil > > > > > > > > > > I forgot to precise, this issue occurs when the "GXL PHY driver" is > > > disabled, > > > only relying on the > > > Generic PHY Driver. > > > > > > [ 630.767538] Generic PHY 0.e40908ff:08: attached PHY driver [Generic > > > PHY] > > > (mii_bus:phy_addr=0.e40908ff:08, irq=-1) > > > > > > > > > When the PHY driver is loaded the issue disappears, with and without your > > > patch. > > > > > > [ 25.355620] Meson GXL Internal PHY 0.e40908ff:08: attached PHY driver > > > [Meson GXL Internal PHY] (mii_bus:phy_addr=0.e40908ff:08, irq=-1) > > > > > > Could you please check the PHY Driver is loaded ? > > > > > > Thanks, > > > Neil > > > > > > _______________________________________________ > > linux-amlogic mailing list > > linux-amlogic@xxxxxxxxxxxxxxxxxxx > > http://lists.infradead.org/mailman/listinfo/linux-amlogic > > > [0] https://github.com/torvalds/linux/blob/master/drivers/net/ethernet/stmicro > /stmmac/dwmac-meson8b.c#L222 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
