Hi Laurent
On Tue, Jul 18, 2017 at 01:18:42PM +0300, Laurent Pinchart wrote:
> On Monday 17 Jul 2017 13:41:49 Rob Herring wrote:
> > On Thu, Jul 13, 2017 at 04:13:06PM +0200, Maxime Ripard wrote:
> > > The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
> > >
> > > Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
> > > ---
> > >
> > > Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 85
> > > +++++++-
> > > 1 file changed, 85 insertions(+)
> > > create mode 100644
> > > Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt>
> > > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > > b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file
> > > mode 100644
> > > index 000000000000..2e7c5aa7020f
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > > @@ -0,0 +1,85 @@
> > > +Allwinner A31 DSI Encoder
> > > +=========================
> > > +
> > > +The DSI pipeline consists of two separate blocks: the DSI controller
> > > +itself, and its associated D-PHY.
> > > +
> > > +DSI Encoder
> > > +-----------
> > > +
> > > +The DSI Encoder generates the DSI signal from the TCON's.
> > > +
> > > +Required properties:
> > > + - compatible: value must be one of:
> > > + * allwinner,sun6i-a31-mipi-dsi
> > > + - reg: base address and size of memory-mapped region
> > > + - interrupts: interrupt associated to this IP
> > > + - clocks: phandles to the clocks feeding the DSI encoder
> > > + * bus: the DSI interface clock
> > > + * mod: the DSI module clock
> > > + - clock-names: the clock names mentioned above
> > > + - phys: phandle to the D-PHY
> > > + - phy-names: must be "dphy"
> > > + - resets: phandle to the reset controller driving the encoder
> > > +
> > > + - ports: A ports node with endpoint definitions as defined in
> > > + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > + port should be the input endpoint, usually coming from the
> > > + associated TCON.
> >
> > Output port for bridge/panel?
> >
> > > +
> > > +D-PHY
> > > +-----
> > > +
> > > +Required properties:
> > > + - compatible: value must be one of:
> > > + * allwinner,sun6i-a31-mipi-dphy
> > > + - reg: base address and size of memory-mapped region
> > > + - clocks: phandles to the clocks feeding the DSI encoder
> > > + * bus: the DSI interface clock
> > > + * mod: the DSI module clock
> > > + - clock-names: the clock names mentioned above
> > > + - resets: phandle to the reset controller driving the encoder
> > > +
> > > +Example:
> > > +
> > > +dsi0: dsi@01ca0000 {
> >
> > Drop the leading 0.
> >
> > > + compatible = "allwinner,sun6i-a31-mipi-dsi";
> > > + reg = <0x01ca0000 0x1000>;
> > > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> > > + clocks = <&ccu CLK_BUS_MIPI_DSI>,
> > > + <&ccu CLK_DSI_SCLK>;
> > > + clock-names = "bus", "mod";
> > > + resets = <&ccu RST_BUS_MIPI_DSI>;
> > > + phys = <&dphy0>;
> > > + phy-names = "dphy";
> > >
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> >
> > Not needed.
> >
> > > +
> > > + ports {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + dsi0_in: port@0 {
>
> I don't think the label for the port is needed, you should only reference the
> endpoint.
>
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + reg = <0>;
> > > +
> > > + dsi0_in_tcon0: endpoint@0 {
> > > + reg = <0>;
> >
> > Don't need reg when there's only 1 endpoint.
>
> And no reg for the port name either when there's a single port. This can all
> be simplified to
>
> dsi0: dsi@1ca0000 {
> compatible = "allwinner,sun6i-a31-mipi-dsi";
> reg = <0x01ca0000 0x1000>;
> interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&ccu CLK_BUS_MIPI_DSI>,
> <&ccu CLK_DSI_SCLK>;
> clock-names = "bus", "mod";
> resets = <&ccu RST_BUS_MIPI_DSI>;
> phys = <&dphy0>;
> phy-names = "dphy";
>
> port {
> dsi0_in_tcon0: endpoint {
> remote-endpoint = <&tcon0_out_dsi0>;
> };
> };
> };
I'll change that. Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
Attachment:
signature.asc
Description: PGP signature
