Add a Synopsys Designware MIPI DSI host DRM bridge driver, based on the Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs. Signed-off-by: Philippe CORNU <philippe.cornu@xxxxxx> --- drivers/gpu/drm/bridge/synopsys/Kconfig | 6 + drivers/gpu/drm/bridge/synopsys/Makefile | 2 + drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 981 ++++++++++++++++++++++++++ include/drm/bridge/dw_mipi_dsi.h | 39 + 4 files changed, 1028 insertions(+) create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c create mode 100644 include/drm/bridge/dw_mipi_dsi.h diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig index 53e78d0..a2fb939 100644 --- a/drivers/gpu/drm/bridge/synopsys/Kconfig +++ b/drivers/gpu/drm/bridge/synopsys/Kconfig @@ -22,3 +22,9 @@ config DRM_DW_HDMI_I2S_AUDIO help Support the I2S Audio interface which is part of the Synopsys Designware HDMI block. + +config DRM_DW_MIPI_DSI + tristate + select DRM_KMS_HELPER + select DRM_MIPI_DSI + select DRM_PANEL_BRIDGE diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile index 17aa7a6..5f57d36 100644 --- a/drivers/gpu/drm/bridge/synopsys/Makefile +++ b/drivers/gpu/drm/bridge/synopsys/Makefile @@ -3,3 +3,5 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o obj-$(CONFIG_DRM_DW_HDMI_I2S_AUDIO) += dw-hdmi-i2s-audio.o + +obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c new file mode 100644 index 0000000..36f5ccb --- /dev/null +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c @@ -0,0 +1,981 @@ +/* + * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd + * Copyright (C) STMicroelectronics SA 2017 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Modified by Philippe Cornu <philippe.cornu@xxxxxx> + * This generic Synopsys DesignWare MIPI DSI host driver is based on the + * Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs. + */ + +#include <linux/clk.h> +#include <linux/component.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/pm_runtime.h> +#include <linux/reset.h> +#include <drm/drmP.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_crtc.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/bridge/dw_mipi_dsi.h> +#include <video/mipi_display.h> + +#define DSI_VERSION 0x00 +#define DSI_PWR_UP 0x04 +#define RESET 0 +#define POWERUP BIT(0) + +#define DSI_CLKMGR_CFG 0x08 +#define TO_CLK_DIVIDSION(div) (((div) & 0xff) << 8) +#define TX_ESC_CLK_DIVIDSION(div) (((div) & 0xff) << 0) + +#define DSI_DPI_VCID 0x0c +#define DPI_VID(vid) (((vid) & 0x3) << 0) + +#define DSI_DPI_COLOR_CODING 0x10 +#define EN18_LOOSELY BIT(8) +#define DPI_COLOR_CODING_16BIT_1 0x0 +#define DPI_COLOR_CODING_16BIT_2 0x1 +#define DPI_COLOR_CODING_16BIT_3 0x2 +#define DPI_COLOR_CODING_18BIT_1 0x3 +#define DPI_COLOR_CODING_18BIT_2 0x4 +#define DPI_COLOR_CODING_24BIT 0x5 + +#define DSI_DPI_CFG_POL 0x14 +#define COLORM_ACTIVE_LOW BIT(4) +#define SHUTD_ACTIVE_LOW BIT(3) +#define HSYNC_ACTIVE_LOW BIT(2) +#define VSYNC_ACTIVE_LOW BIT(1) +#define DATAEN_ACTIVE_LOW BIT(0) + +#define DSI_DPI_LP_CMD_TIM 0x18 +#define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16) +#define INVACT_LPCMD_TIME(p) ((p) & 0xff) + +#define DSI_DBI_CFG 0x20 +#define DSI_DBI_CMDSIZE 0x28 + +#define DSI_PCKHDL_CFG 0x2c +#define EN_CRC_RX BIT(4) +#define EN_ECC_RX BIT(3) +#define EN_BTA BIT(2) +#define EN_EOTP_RX BIT(1) +#define EN_EOTP_TX BIT(0) + +#define DSI_MODE_CFG 0x34 +#define ENABLE_VIDEO_MODE 0 +#define ENABLE_CMD_MODE BIT(0) + +#define DSI_VID_MODE_CFG 0x38 +#define FRAME_BTA_ACK BIT(14) +#define ENABLE_LOW_POWER (0x3f << 8) +#define ENABLE_LOW_POWER_MASK (0x3f << 8) +#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES 0x0 +#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS 0x1 +#define VID_MODE_TYPE_BURST 0x2 +#define VID_MODE_TYPE_MASK 0x3 + +#define DSI_VID_PKT_SIZE 0x3c +#define VID_PKT_SIZE(p) (((p) & 0x3fff) << 0) +#define VID_PKT_MAX_SIZE 0x3fff + +#define DSI_VID_HSA_TIME 0x48 +#define DSI_VID_HBP_TIME 0x4c +#define DSI_VID_HLINE_TIME 0x50 +#define DSI_VID_VSA_LINES 0x54 +#define DSI_VID_VBP_LINES 0x58 +#define DSI_VID_VFP_LINES 0x5c +#define DSI_VID_VACTIVE_LINES 0x60 +#define DSI_CMD_MODE_CFG 0x68 +#define MAX_RD_PKT_SIZE_LP BIT(24) +#define DCS_LW_TX_LP BIT(19) +#define DCS_SR_0P_TX_LP BIT(18) +#define DCS_SW_1P_TX_LP BIT(17) +#define DCS_SW_0P_TX_LP BIT(16) +#define GEN_LW_TX_LP BIT(14) +#define GEN_SR_2P_TX_LP BIT(13) +#define GEN_SR_1P_TX_LP BIT(12) +#define GEN_SR_0P_TX_LP BIT(11) +#define GEN_SW_2P_TX_LP BIT(10) +#define GEN_SW_1P_TX_LP BIT(9) +#define GEN_SW_0P_TX_LP BIT(8) +#define EN_ACK_RQST BIT(1) +#define EN_TEAR_FX BIT(0) + +#define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \ + DCS_LW_TX_LP | \ + DCS_SR_0P_TX_LP | \ + DCS_SW_1P_TX_LP | \ + DCS_SW_0P_TX_LP | \ + GEN_LW_TX_LP | \ + GEN_SR_2P_TX_LP | \ + GEN_SR_1P_TX_LP | \ + GEN_SR_0P_TX_LP | \ + GEN_SW_2P_TX_LP | \ + GEN_SW_1P_TX_LP | \ + GEN_SW_0P_TX_LP) + +#define DSI_GEN_HDR 0x6c +#define GEN_HDATA(data) (((data) & 0xffff) << 8) +#define GEN_HDATA_MASK (0xffff << 8) +#define GEN_HTYPE(type) (((type) & 0xff) << 0) +#define GEN_HTYPE_MASK 0xff + +#define DSI_GEN_PLD_DATA 0x70 + +#define DSI_CMD_PKT_STATUS 0x74 +#define GEN_CMD_EMPTY BIT(0) +#define GEN_CMD_FULL BIT(1) +#define GEN_PLD_W_EMPTY BIT(2) +#define GEN_PLD_W_FULL BIT(3) +#define GEN_PLD_R_EMPTY BIT(4) +#define GEN_PLD_R_FULL BIT(5) +#define GEN_RD_CMD_BUSY BIT(6) + +#define DSI_TO_CNT_CFG 0x78 +#define HSTX_TO_CNT(p) (((p) & 0xffff) << 16) +#define LPRX_TO_CNT(p) ((p) & 0xffff) + +#define DSI_BTA_TO_CNT 0x8c +#define DSI_LPCLK_CTRL 0x94 +#define AUTO_CLKLANE_CTRL BIT(1) +#define PHY_TXREQUESTCLKHS BIT(0) + +#define DSI_PHY_TMR_LPCLK_CFG 0x98 +#define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16) +#define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff) + +#define DSI_PHY_TMR_CFG 0x9c +#define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24) +#define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16) +#define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff) + +#define DSI_PHY_RSTZ 0xa0 +#define PHY_DISFORCEPLL 0 +#define PHY_ENFORCEPLL BIT(3) +#define PHY_DISABLECLK 0 +#define PHY_ENABLECLK BIT(2) +#define PHY_RSTZ 0 +#define PHY_UNRSTZ BIT(1) +#define PHY_SHUTDOWNZ 0 +#define PHY_UNSHUTDOWNZ BIT(0) + +#define DSI_PHY_IF_CFG 0xa4 +#define N_LANES(n) ((((n) - 1) & 0x3) << 0) +#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) + +#define DSI_PHY_STATUS 0xb0 +#define LOCK BIT(0) +#define STOP_STATE_CLK_LANE BIT(2) + +#define DSI_PHY_TST_CTRL0 0xb4 +#define PHY_TESTCLK BIT(1) +#define PHY_UNTESTCLK 0 +#define PHY_TESTCLR BIT(0) +#define PHY_UNTESTCLR 0 + +#define DSI_PHY_TST_CTRL1 0xb8 +#define PHY_TESTEN BIT(16) +#define PHY_UNTESTEN 0 +#define PHY_TESTDOUT(n) (((n) & 0xff) << 8) +#define PHY_TESTDIN(n) (((n) & 0xff) << 0) + +#define DSI_INT_ST0 0xbc +#define DSI_INT_ST1 0xc0 +#define DSI_INT_MSK0 0xc4 +#define DSI_INT_MSK1 0xc8 + +#define PHY_STATUS_TIMEOUT_US 10000 +#define CMD_PKT_STATUS_TIMEOUT_US 20000 + +struct dw_mipi_dsi { + struct drm_bridge bridge; + struct mipi_dsi_host dsi_host; + struct drm_bridge *panel_bridge; + bool is_panel_bridge; + struct device *dev; + void __iomem *base; + + struct clk *pclk; + + unsigned int lane_mbps; /* per lane */ + u32 channel; + u32 lanes; + u32 format; + unsigned long mode_flags; + + const struct dw_mipi_dsi_plat_data *plat_data; +}; + +/* + * The controller should generate 2 frames before + * preparing the peripheral. + */ +static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode) +{ + int refresh, two_frames; + + refresh = drm_mode_vrefresh(mode); + two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2; + msleep(two_frames); +} + +static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host) +{ + return container_of(host, struct dw_mipi_dsi, dsi_host); +} + +static inline struct dw_mipi_dsi *bridge_to_dsi(struct drm_bridge *bridge) +{ + return container_of(bridge, struct dw_mipi_dsi, bridge); +} + +static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val) +{ + writel(val, dsi->base + reg); +} + +static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg) +{ + return readl(dsi->base + reg); +} + +static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi *dsi = host_to_dsi(host); + struct drm_bridge *bridge; + struct drm_panel *panel; + int ret; + + if (device->lanes > dsi->plat_data->max_data_lanes) { + dev_err(dsi->dev, "the number of data lanes(%u) is too many\n", + device->lanes); + return -EINVAL; + } + + dsi->lanes = device->lanes; + dsi->channel = device->channel; + dsi->format = device->format; + dsi->mode_flags = device->mode_flags; + + ret = drm_of_find_panel_or_bridge(host->dev->of_node, 1, 0, + &panel, &bridge); + if (ret) + return ret; + + if (panel) { + bridge = drm_panel_bridge_add(panel, DRM_MODE_CONNECTOR_DSI); + if (IS_ERR(bridge)) + return PTR_ERR(bridge); + dsi->is_panel_bridge = true; + } + + dsi->panel_bridge = bridge; + + drm_bridge_add(&dsi->bridge); + + return 0; +} + +static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, + struct mipi_dsi_device *device) +{ + struct dw_mipi_dsi *dsi = host_to_dsi(host); + + if (dsi->is_panel_bridge) + drm_panel_bridge_remove(dsi->panel_bridge); + + drm_bridge_remove(&dsi->bridge); + + return 0; +} + +static void dw_mipi_message_config(struct dw_mipi_dsi *dsi, + const struct mipi_dsi_msg *msg) +{ + bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM; + u32 val = 0; + + if (msg->flags & MIPI_DSI_MSG_REQ_ACK) + val |= EN_ACK_RQST; + if (lpm) + val |= CMD_MODE_ALL_LP; + + dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS); + dsi_write(dsi, DSI_CMD_MODE_CFG, val); +} + +static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val) +{ + int ret; + u32 val, mask; + + ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, + val, !(val & GEN_CMD_FULL), 1000, + CMD_PKT_STATUS_TIMEOUT_US); + if (ret < 0) { + dev_err(dsi->dev, "failed to get available command FIFO\n"); + return ret; + } + + dsi_write(dsi, DSI_GEN_HDR, hdr_val); + + mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY; + ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, + val, (val & mask) == mask, + 1000, CMD_PKT_STATUS_TIMEOUT_US); + if (ret < 0) { + dev_err(dsi->dev, "failed to write command FIFO\n"); + return ret; + } + + return 0; +} + +static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi, + const struct mipi_dsi_msg *msg) +{ + const u8 *tx_buf = msg->tx_buf; + u16 data = 0; + u32 val; + + if (msg->tx_len > 0) + data |= tx_buf[0]; + if (msg->tx_len > 1) + data |= tx_buf[1] << 8; + + if (msg->tx_len > 2) { + dev_err(dsi->dev, "too long tx buf length %zu for short write\n", + msg->tx_len); + return -EINVAL; + } + + val = GEN_HDATA(data) | GEN_HTYPE(msg->type); + return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val); +} + +static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi, + const struct mipi_dsi_msg *msg) +{ + const u8 *tx_buf = msg->tx_buf; + int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret; + u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type); + u32 remainder; + u32 val; + + if (msg->tx_len < 3) { + dev_err(dsi->dev, "wrong tx buf length %zu for long write\n", + msg->tx_len); + return -EINVAL; + } + + while (DIV_ROUND_UP(len, pld_data_bytes)) { + if (len < pld_data_bytes) { + remainder = 0; + memcpy(&remainder, tx_buf, len); + dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); + len = 0; + } else { + memcpy(&remainder, tx_buf, pld_data_bytes); + dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); + tx_buf += pld_data_bytes; + len -= pld_data_bytes; + } + + ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS, + val, !(val & GEN_PLD_W_FULL), 1000, + CMD_PKT_STATUS_TIMEOUT_US); + if (ret < 0) { + dev_err(dsi->dev, + "failed to get available write payload FIFO\n"); + return ret; + } + } + + return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val); +} + +static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, + const struct mipi_dsi_msg *msg) +{ + struct dw_mipi_dsi *dsi = host_to_dsi(host); + int ret; + + /* + * TODO dw drv improvements + * use mipi_dsi_create_packet() instead of all following + * functions and code (no switch cases, no + * dw_mipi_dsi_dcs_short_write(), only the loop in long_write...) + * and use packet.header... + */ + dw_mipi_message_config(dsi, msg); + + switch (msg->type) { + case MIPI_DSI_DCS_SHORT_WRITE: + case MIPI_DSI_DCS_SHORT_WRITE_PARAM: + case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE: + ret = dw_mipi_dsi_dcs_short_write(dsi, msg); + break; + case MIPI_DSI_DCS_LONG_WRITE: + ret = dw_mipi_dsi_dcs_long_write(dsi, msg); + break; + default: + dev_err(dsi->dev, "unsupported message type 0x%02x\n", + msg->type); + ret = -EINVAL; + } + + return ret; +} + +static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = { + .attach = dw_mipi_dsi_host_attach, + .detach = dw_mipi_dsi_host_detach, + .transfer = dw_mipi_dsi_host_transfer, +}; + +static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi) +{ + u32 val; + + /* + * TODO dw drv improvements + * enabling low power is panel-dependent, we should use the + * panel configuration here... + */ + val = ENABLE_LOW_POWER; + + if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) + val |= VID_MODE_TYPE_BURST; + else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) + val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES; + else + val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS; + + dsi_write(dsi, DSI_VID_MODE_CFG, val); +} + +static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi, + unsigned long mode_flags) +{ + dsi_write(dsi, DSI_PWR_UP, RESET); + + if (mode_flags & MIPI_DSI_MODE_VIDEO) { + dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE); + dw_mipi_dsi_video_mode_config(dsi); + dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS); + } else { + dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); + } + + dsi_write(dsi, DSI_PWR_UP, POWERUP); +} + +static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi) +{ + dsi_write(dsi, DSI_PWR_UP, RESET); + dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ); +} + +static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi) +{ + /* + * The maximum permitted escape clock is 20MHz and it is derived from + * lanebyteclk, which is running at "lane_mbps / 8". Thus we want: + * + * (lane_mbps >> 3) / esc_clk_division < 20 + * which is: + * (lane_mbps >> 3) / 20 > esc_clk_division + */ + u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1; + + dsi_write(dsi, DSI_PWR_UP, RESET); + + /* + * TODO dw drv improvements + * timeout clock division should be computed with the + * high speed transmission counter timeout and byte lane... + */ + dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) | + TX_ESC_CLK_DIVIDSION(esc_clk_division)); +} + +static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi, + struct drm_display_mode *mode) +{ + u32 val = 0, color = 0; + + switch (dsi->format) { + case MIPI_DSI_FMT_RGB888: + color = DPI_COLOR_CODING_24BIT; + break; + case MIPI_DSI_FMT_RGB666: + color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY; + break; + case MIPI_DSI_FMT_RGB666_PACKED: + color = DPI_COLOR_CODING_18BIT_1; + break; + case MIPI_DSI_FMT_RGB565: + color = DPI_COLOR_CODING_16BIT_1; + break; + } + + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + val |= VSYNC_ACTIVE_LOW; + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + val |= HSYNC_ACTIVE_LOW; + + dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel)); + dsi_write(dsi, DSI_DPI_COLOR_CODING, color); + dsi_write(dsi, DSI_DPI_CFG_POL, val); + /* + * TODO dw drv improvements + * largest packet sizes during hfp or during vsa/vpb/vfp + * should be computed according to byte lane, lane number and only + * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS) + */ + dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4) + | INVACT_LPCMD_TIME(4)); +} + +static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi) +{ + dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA); +} + +static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, + struct drm_display_mode *mode) +{ + /* + * TODO dw drv improvements + * only burst mode is supported here. For non-burst video modes, + * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC & + * DSI_VNPCR.NPSIZE... especially because this driver supports + * non-burst video modes, see dw_mipi_dsi_video_mode_config()... + */ + dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); +} + +static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) +{ + /* + * TODO dw drv improvements + * compute high speed transmission counter timeout according + * to the timeout clock division (TO_CLK_DIVIDSION) and byte lane... + */ + dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000)); + /* + * TODO dw drv improvements + * the Bus-Turn-Around Timeout Counter should be computed + * according to byte lane... + */ + dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00); + dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); +} + +/* Get lane byte clock cycles. */ +static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi, + struct drm_display_mode *mode, + u32 hcomponent) +{ + u32 frac, lbcc; + + lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8; + + frac = lbcc % mode->clock; + lbcc = lbcc / mode->clock; + if (frac) + lbcc++; + + return lbcc; +} + +static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi, + struct drm_display_mode *mode) +{ + u32 htotal, hsa, hbp, lbcc; + + htotal = mode->htotal; + hsa = mode->hsync_end - mode->hsync_start; + hbp = mode->htotal - mode->hsync_end; + + /* + * TODO dw drv improvements + * computations below may be improved... + */ + lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal); + dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc); + + lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa); + dsi_write(dsi, DSI_VID_HSA_TIME, lbcc); + + lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp); + dsi_write(dsi, DSI_VID_HBP_TIME, lbcc); +} + +static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi, + struct drm_display_mode *mode) +{ + u32 vactive, vsa, vfp, vbp; + + vactive = mode->vdisplay; + vsa = mode->vsync_end - mode->vsync_start; + vfp = mode->vsync_start - mode->vdisplay; + vbp = mode->vtotal - mode->vsync_end; + + dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive); + dsi_write(dsi, DSI_VID_VSA_LINES, vsa); + dsi_write(dsi, DSI_VID_VFP_LINES, vfp); + dsi_write(dsi, DSI_VID_VBP_LINES, vbp); +} + +static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi) +{ + /* + * TODO dw drv improvements + * data & clock lane timers should be computed according to panel + * blankings and to the automatic clock lane control mode... + * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with + * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP) + */ + dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40) + | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000)); + + dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40) + | PHY_CLKLP2HS_TIME(0x40)); +} + +static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi) +{ + /* + * TODO dw drv improvements + * stop wait time should be the maximum between host dsi + * and panel stop wait times + */ + dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) | + N_LANES(dsi->lanes)); +} + +static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi) +{ + /* Clear PHY state */ + dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK + | PHY_RSTZ | PHY_SHUTDOWNZ); + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR); + dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR); +} + +static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi) +{ + u32 val; + int ret; + + dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK | + PHY_UNRSTZ | PHY_UNSHUTDOWNZ); + + ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, + val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US); + if (ret < 0) + DRM_DEBUG_DRIVER("failed to wait phy lock state\n"); + + ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, + val, val & STOP_STATE_CLK_LANE, 1000, + PHY_STATUS_TIMEOUT_US); + if (ret < 0) + DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n"); +} + +static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi) +{ + dsi_read(dsi, DSI_INT_ST0); + dsi_read(dsi, DSI_INT_ST1); + dsi_write(dsi, DSI_INT_MSK0, 0); + dsi_write(dsi, DSI_INT_MSK1, 0); +} + +static void dw_mipi_dsi_bridge_post_disable(struct drm_bridge *bridge) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + + /* + * Switch to command mode before panel-bridge post_disable & + * panel unprepare. + * Note: panel-bridge disable & panel disable has been called + * before by the drm framework. + */ + dw_mipi_dsi_set_mode(dsi, 0); + + /* + * TODO Only way found to call panel-bridge post_disable & + * panel unprepare before the dsi "final" disable... + * This needs to be fixed in the drm_bridge framework and the API + * needs to be updated to manage our own call chains... + */ + dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge); + + dw_mipi_dsi_disable(dsi); + clk_disable_unprepare(dsi->pclk); + pm_runtime_put(dsi->dev); +} + +void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops; + void *priv_data = dsi->plat_data->priv_data; + int ret; + + clk_prepare_enable(dsi->pclk); + + ret = phy_ops->get_lane_mbps(priv_data, mode, dsi->mode_flags, + dsi->lanes, dsi->format, &dsi->lane_mbps); + if (ret) + DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n"); + + pm_runtime_get_sync(dsi->dev); + dw_mipi_dsi_init(dsi); + dw_mipi_dsi_dpi_config(dsi, mode); + dw_mipi_dsi_packet_handler_config(dsi); + dw_mipi_dsi_video_mode_config(dsi); + dw_mipi_dsi_video_packet_config(dsi, mode); + dw_mipi_dsi_command_mode_config(dsi); + dw_mipi_dsi_line_timer_config(dsi, mode); + dw_mipi_dsi_vertical_timing_config(dsi, mode); + + dw_mipi_dsi_dphy_init(dsi); + dw_mipi_dsi_dphy_timing_config(dsi); + dw_mipi_dsi_dphy_interface_config(dsi); + + dw_mipi_dsi_clear_err(dsi); + + ret = phy_ops->init(priv_data); + if (ret) + DRM_DEBUG_DRIVER("Phy init() failed\n"); + + dw_mipi_dsi_dphy_enable(dsi); + + dw_mipi_dsi_wait_for_two_frames(mode); + + /* Switch to cmd mode for panel-bridge pre_enable & panel prepare */ + dw_mipi_dsi_set_mode(dsi, 0); +} + +static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + + /* Switch to video mode for panel-bridge enable & panel enable */ + dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO); +} + +static enum drm_mode_status +dw_mipi_dsi_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_mode *mode) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data; + enum drm_mode_status mode_status = MODE_OK; + + if (pdata->mode_valid) + mode_status = pdata->mode_valid(pdata->priv_data, mode); + + return mode_status; +} + +static int dw_mipi_dsi_bridge_attach(struct drm_bridge *bridge) +{ + struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge); + + if (!bridge->encoder) { + DRM_ERROR("Parent encoder object not found\n"); + return -ENODEV; + } + + /* Set the encoder type as caller does not know it */ + bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI; + + /* Attach the panel-bridge to the dsi bridge */ + return drm_bridge_attach(bridge->encoder, dsi->panel_bridge, bridge); +} + +static struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = { + .mode_set = dw_mipi_dsi_bridge_mode_set, + .enable = dw_mipi_dsi_bridge_enable, + .post_disable = dw_mipi_dsi_bridge_post_disable, + .mode_valid = dw_mipi_dsi_bridge_mode_valid, + .attach = dw_mipi_dsi_bridge_attach, +}; + +static struct dw_mipi_dsi * +__dw_mipi_dsi_probe(struct platform_device *pdev, + const struct dw_mipi_dsi_plat_data *plat_data) +{ + struct device *dev = &pdev->dev; + struct reset_control *apb_rst; + struct dw_mipi_dsi *dsi; + struct resource *res; + int ret; + + dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); + if (!dsi) + return ERR_PTR(-ENOMEM); + + dsi->dev = dev; + dsi->plat_data = plat_data; + + if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps) { + DRM_ERROR("Phy not properly configured\n"); + return ERR_PTR(-ENODEV); + } + + if (!plat_data->base) { + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return ERR_PTR(-ENODEV); + + dsi->base = devm_ioremap_resource(dev, res); + if (IS_ERR(dsi->base)) + return ERR_PTR(-ENODEV); + + } else { + dsi->base = plat_data->base; + } + + dsi->pclk = devm_clk_get(dev, "pclk"); + if (IS_ERR(dsi->pclk)) { + ret = PTR_ERR(dsi->pclk); + dev_err(dev, "Unable to get pclk: %d\n", ret); + return ERR_PTR(ret); + } + + /* + * Note that the reset was not defined in the initial device tree, so + * we have to be prepared for it not being found. + */ + apb_rst = devm_reset_control_get(dev, "apb"); + if (IS_ERR(apb_rst)) { + ret = PTR_ERR(apb_rst); + if (ret == -ENOENT) { + apb_rst = NULL; + } else { + dev_err(dev, "Unable to get reset control: %d\n", ret); + return ERR_PTR(ret); + } + } + + if (apb_rst) { + ret = clk_prepare_enable(dsi->pclk); + if (ret) { + dev_err(dev, "%s: Failed to enable pclk\n", __func__); + return ERR_PTR(ret); + } + + reset_control_assert(apb_rst); + usleep_range(10, 20); + reset_control_deassert(apb_rst); + + clk_disable_unprepare(dsi->pclk); + } + + pm_runtime_enable(dev); + + dsi->dsi_host.ops = &dw_mipi_dsi_host_ops; + dsi->dsi_host.dev = dev; + ret = mipi_dsi_host_register(&dsi->dsi_host); + if (ret) { + dev_err(dev, "Failed to register MIPI host: %d\n", ret); + return ERR_PTR(ret); + } + + dsi->bridge.driver_private = dsi; + dsi->bridge.funcs = &dw_mipi_dsi_bridge_funcs; +#ifdef CONFIG_OF + dsi->bridge.of_node = pdev->dev.of_node; +#endif + + dev_set_drvdata(dev, dsi); + + return dsi; +} + +static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi) +{ + pm_runtime_disable(dsi->dev); +} + +/* + * Probe/remove API, used from platforms based on the DRM bridge API. + */ +int dw_mipi_dsi_probe(struct platform_device *pdev, + const struct dw_mipi_dsi_plat_data *plat_data) +{ + struct dw_mipi_dsi *dsi; + + dsi = __dw_mipi_dsi_probe(pdev, plat_data); + if (IS_ERR(dsi)) + return PTR_ERR(dsi); + + return 0; +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe); + +void dw_mipi_dsi_remove(struct platform_device *pdev) +{ + struct dw_mipi_dsi *dsi = platform_get_drvdata(pdev); + + mipi_dsi_host_unregister(&dsi->dsi_host); + + __dw_mipi_dsi_remove(dsi); +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove); + +/* + * Bind/unbind API, used from platforms based on the component framework. + */ +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder, + const struct dw_mipi_dsi_plat_data *plat_data) +{ + struct dw_mipi_dsi *dsi; + int ret; + + dsi = __dw_mipi_dsi_probe(pdev, plat_data); + if (IS_ERR(dsi)) + return PTR_ERR(dsi); + + ret = drm_bridge_attach(encoder, &dsi->bridge, NULL); + if (ret) { + dw_mipi_dsi_remove(pdev); + DRM_ERROR("Failed to initialize bridge with drm\n"); + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind); + +void dw_mipi_dsi_unbind(struct device *dev) +{ + struct dw_mipi_dsi *dsi = dev_get_drvdata(dev); + + __dw_mipi_dsi_remove(dsi); +} +EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind); + +MODULE_AUTHOR("Chris Zhong <zyw@xxxxxxxxxxxxxx>"); +MODULE_AUTHOR("Philippe Cornu <philippe.cornu@xxxxxx>"); +MODULE_DESCRIPTION("DW MIPI DSI host controller driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:dw-mipi-dsi"); diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h new file mode 100644 index 0000000..9b30fec --- /dev/null +++ b/include/drm/bridge/dw_mipi_dsi.h @@ -0,0 +1,39 @@ +/* + * Copyright (C) STMicroelectronics SA 2017 + * + * Authors: Philippe Cornu <philippe.cornu@xxxxxx> + * Yannick Fertre <yannick.fertre@xxxxxx> + * + * License terms: GNU General Public License (GPL), version 2 + */ + +#ifndef __DW_MIPI_DSI__ +#define __DW_MIPI_DSI__ + +struct dw_mipi_dsi_phy_ops { + int (*init)(void *priv_data); + int (*get_lane_mbps)(void *priv_data, struct drm_display_mode *mode, + unsigned long mode_flags, u32 lanes, u32 format, + unsigned int *lane_mbps); +}; + +struct dw_mipi_dsi_plat_data { + void __iomem *base; + unsigned int max_data_lanes; + + enum drm_mode_status (*mode_valid)(void *priv_data, + const struct drm_display_mode *mode); + + const struct dw_mipi_dsi_phy_ops *phy_ops; + + void *priv_data; +}; + +int dw_mipi_dsi_probe(struct platform_device *pdev, + const struct dw_mipi_dsi_plat_data *plat_data); +void dw_mipi_dsi_remove(struct platform_device *pdev); +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder, + const struct dw_mipi_dsi_plat_data *plat_data); +void dw_mipi_dsi_unbind(struct device *dev); + +#endif /* __DW_MIPI_DSI__ */ -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html