This patch adds the binding documentation for Spreadtrum SC9860 pin
controller device.
Signed-off-by: Baolin Wang <baolin.wang@xxxxxxxxxxxxxx>
---
Changes since v4:
- Remove these sleep related configs and only introduce one sleep
state config to indicate this is sleep state.
Changes since v3:
- Use generic "bias-pull-up" instead of "sprd,pull-up".
- Change subject name.
- Use generic sleep related config.
- Add more explanation for sleep related configuration and sleep mode.
Changes since v2:
- No updates.
Changes since v1:
- Remove magic numbers and get to use the standard bindings.
- Fix some typos.
---
.../devicetree/bindings/pinctrl/sprd,pinctrl.txt | 83 ++++++++++++++++++++
.../bindings/pinctrl/sprd,sc9860-pinctrl.txt | 70 +++++++++++++++++
2 files changed, 153 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt
new file mode 100644
index 0000000..b1cea7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/sprd,pinctrl.txt
@@ -0,0 +1,83 @@
+* Spreadtrum Pin Controller
+
+The Spreadtrum pin controller are organized in 3 blocks (types).
+
+The first block comprises some global control registers, and each
+register contains several bit fields with one bit or several bits
+to configure for some global common configuration, such as domain
+pad driving level, system control select and so on ("domain pad
+driving level": One pin can output 3.0v or 1.8v, depending on the
+related domain pad driving selection, if the related domain pad
+slect 3.0v, then the pin can output 3.0v. "system control" is used
+to choose one function (like: UART0) for which system, since we
+have several systems (AP/CP/CM4) on one SoC.).
+
+There are too much various configuration that we can not list all
+of them, so we can not make every Spreadtrum-special configuration
+as one generic configuration, and maybe it will add more strange
+global configuration in future. Then we add one "sprd,control" to
+set these various global control configuration, and we need use
+magic number for this property.
+
+Moreover we recognise every fields comprising one bit or several
+bits in one global control register as one pin, thus we should
+record every pin's bit offset, bit width and register offset to
+configure this field (pin).
+
+The second block comprises some common registers which have unified
+register definition, and each register described one pin is used
+to configure the pin sleep mode, function select and sleep related
+configuration.
+
+Now we have 4 systems for sleep mode on SC9860 SoC: AP system,
+PUBCP system, TGLDSP system and AGDSP system. And the pin sleep
+related configuration are:
+- input-enable
+- input-disable
+- output-high
+- output-low
+- bias-pull-up
+- bias-pull-down
+
+In some situation we need set the pin sleep mode and pin sleep related
+configuration, to set the pin sleep related configuration automatically
+by hardware when the system specified by sleep mode goes into deep
+sleep mode. For example, if we set the pin sleep mode as PUBCP_SLEEP
+and set the pin sleep related configuration as "input-enable", which
+means when PUBCP system goes into deep sleep mode, this pin will be set
+input enable automatically.
+
+Moreover we can not use the "sleep" state, since some systems (like:
+PUBCP system) do not run linux kernel OS (only AP system run linux
+kernel on SC9860 platform), then we can not select "sleep" state
+when the PUBCP system goes into deep sleep mode. Thus we introduce
+"sprd,sleep-mode" property to set pin sleep mode.
+
+The last block comprises some misc registers which also have unified
+register definition, and each register described one pin is used to
+configure drive strength, pull up/down and so on. Especially for pull
+up, we have two kind pull up resistor: 20K and 4.7K.
+
+Required properties for Spreadtrum pin controller:
+- compatible: "sprd,<soc>-pinctrl"
+ Please refer to each sprd,<soc>-pinctrl.txt binding doc for supported SoCs.
+- reg: The register address of pin controller device.
+- pins : An array of pin names.
+
+Optional properties:
+- function: Specified the function name.
+- drive-strength: Drive strength in mA.
+- input-schmitt-disable: Enable schmitt-trigger mode.
+- input-schmitt-enable: Disable schmitt-trigger mode.
+- bias-disable: Disable pin bias.
+- bias-pull-down: Pull down on pin.
+- bias-pull-up: Pull up on pin.
+- input-enable: Enable pin input.
+- input-disable: Enable pin output.
+- output-high: Set the pin as an output level high.
+- output-low: Set the pin as an output level low.
+- sleep-hardware-state: Indicate these configs in this state are sleep related.
+- sprd,control: Control values referring to databook for global control pins.
+- sprd,sleep-mode: Sleep mode selection.
+
+Please refer to each sprd,<soc>-pinctrl.txt binding doc for supported values.
diff --git a/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt
new file mode 100644
index 0000000..745845c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/sprd,sc9860-pinctrl.txt
@@ -0,0 +1,70 @@
+* Spreadtrum SC9860 Pin Controller
+
+Please refer to sprd,pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: Must be "sprd,sc9860-pinctrl".
+- reg: The register address of pin controller device.
+- pins : An array of strings, each string containing the name of a pin.
+
+Optional properties:
+- function: A string containing the name of the function, values must be
+ one of: "func1", "func2", "func3" and "func4".
+- drive-strength: Drive strength in mA. Supported values: 2, 4, 6, 8, 10,
+ 12, 14, 16, 20, 21, 24, 25, 27, 29, 31 and 33.
+- input-schmitt-disable: Enable schmitt-trigger mode.
+- input-schmitt-enable: Disable schmitt-trigger mode.
+- bias-disable: Disable pin bias.
+- bias-pull-down: Pull down on pin.
+- bias-pull-up: Pull up on pin. Supported values: 20000 for pull-up resistor
+ is 20K and 4700 for pull-up resistor is 4.7K.
+- input-enable: Enable pin input.
+- input-disable: Enable pin output.
+- output-high: Set the pin as an output level high.
+- output-low: Set the pin as an output level low.
+- sleep-hardware-state: Indicate these configs in this state are sleep related.
+- sprd,control: Control values referring to databook for global control pins.
+- sprd,sleep-mode: Choose the pin sleep mode, and supported values are:
+ AP_SLEEP, PUBCP_SLEEP, TGLDSP_SLEEP and AGDSP_SLEEP.
+
+Pin sleep mode definition:
+enum pin_sleep_mode {
+ AP_SLEEP = BIT(0),
+ PUBCP_SLEEP = BIT(1),
+ TGLDSP_SLEEP = BIT(2),
+ AGDSP_SLEEP = BIT(3),
+};
+
+Example:
+pin_controller: pinctrl@402a0000 {
+ compatible = "sprd,sc9860-pinctrl";
+ reg = <0x402a0000 0x10000>;
+
+ grp1: sd0 {
+ pins = "SC9860_VIO_SD2_IRTE", "SC9860_VIO_SD0_IRTE";
+ sprd,control = <0x1>;
+ };
+
+ grp2: rfctl_33 {
+ pins = "SC9860_RFCTL33";
+ function = "func2";
+ sprd,sleep-mode = <AP_SLEEP | PUBCP_SLEEP>;
+ grp2_sleep_mode: rfctl_33_sleep {
+ pins = "SC9860_RFCTL33";
+ sleep-hardware-state;
+ output-low;
+ }
+ };
+
+ grp3: rfctl_misc_20 {
+ pins = "SC9860_RFCTL20_MISC";
+ drive-strength = <10>;
+ bias-pull-up = <4700>;
+ grp3_sleep_mode: rfctl_misc_sleep {
+ pins = "SC9860_RFCTL20_MISC";
+ sleep-hardware-state;
+ bias-pull-up;
+ }
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
