Re: [PATCH 0/3] USB Mux support for Chipidea

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Quoting Peter Rosin (2017-07-11 22:04:46)
> On 2017-07-12 03:02, Stephen Boyd wrote:
> > This patchset adds support for the TC7USB40MU usb mux found on 
> > db410c 96boards platforms via the new multiplexer framework and
> > hooks that into the chipidea driver. This allows us to properly
> > control host or device mode on this board via the sysfs knob.
> > 
> > So far I've only tested this on db410c, and there are some rough
> > edges to finish off before it can merge. Also I'm experiencing
> > odd behavior with switching the role while gadget is enabled and
> > the micro-usb cable is kept connected. Not sure what's wrong but
> > it seems like the gadget never gets disconnected? I'll investigate
> > more.
> > 
> > TODO:
> > 
> >  1. The mux framework has to be selected for consumers to use it. We'll
> >     need some stubs in the consumer header file to allow compilation to
> >     continue without mux always enabled by consumers.
> 
> Instead of "depends on MULTIPLEXER", just add "select MULTIPLEXER"
> to the Kconfig. Otherwise, you'll have to convince Linus that we
> really do need a Kconfig question for the subsystem :-)
> 
> https://lkml.org/lkml/2017/7/4/118

Ok. I'll add a select to the chipidea driver.

> 
> >  2. We probably need some sort of mux_control_get_optional() API so that
> >     we know if there was an error getting the mux control, instead of just
> >     ignoring errors. For now I can pass up EPROBE_DEFER errors and ignore
> >     other errors and consider it "missing from DT".
> 
> Yes, mux_control_get_optional should be easy to add.
> 
> >  3. Maybe we can get rid of the mux driver and just use mux-gpio.c with
> >     a compatible string update? I split it off because we may want to
> >     support the "S" pin on the TC7USB40MU one day that shuts off both

Oh this is a typo. I mean "OE" pin.

> >     mux outputs.
> 
> Maybe no need for a compatible update either, if it works to do something
> like this in the DT?
> 
>         usb_switch: usb-switch {
>                 compatible = "gpio-mux";
>                 mux-gpios = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>,
>                             <&pm8916_gpios XXX GPIO_ACTIVE_XXX>;
>                 idle-state = <2>;
>                 #mux-control-cells = <0>;
>                 pinctrl-names = "default";
>                 pinctrl-0 = <&usb_sw_sel_pm>;
>         };
> 
> But I obviously know little about how things are wired and really works,
> so that might be totally off...
> 
> Otherwise, maybe a generic mux-pinctrl driver would do the trick?
> (compare with drivers/i2c/muxes/i2c-mux-pinctrl.c)
> 

Agreed. On the board I have the "OE" pin is shorted so that it always
outputs a signal. For someone else they could do what you say and add
another pin to gpio-mux binding and things will still work.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux