Hi IRQ experts, DT exports,
I have a question about CONFIG_IRQ_DOMAIN_HIERARCHY.
When IRQ domains are hierarchy,
how can we specify IRQ number re-mapping between the
parent irqchip and the child irqchip?
The following figure shows a simplified example.
|----------| |----------| |----------|
| parent | | child | | IRQ |
| IRQ chip | <----- | IRQ chip |<----- | consumer |
| | | | | Device |
|----------| |----------| |----------|
Perhaps, we may describe DT like follows
gic: interrupt-controller {
...
interrupt-controller;
#interrupt-cells = <3>;
};
child_intc: child-interrupt-controller {
...
interrupt-parent = <&gic>;
interrupts = <0 50 0>, <0 51 0>, <0 52 0>, <0 53 0>;
interrupt-controller;
#interrupt-cells = <2>;
};
i2c: i2c {
...
interrupt-parent = <&child_intc>;
interrupts = <0 4>;
};
In this example, the I2C controller takes HWIRQ=0 of the child_intc device.
This goes through the child IRQ chip,
then connected to HWIRQ=50 of the parent intc.
The DT above describes the hardware connection well,
but it actually does not work.
The root irqchip is usually declared with IRQCHIP_DECLARE().
So, IRQ resources are allocated when platform devices are populated from DT.
This means IRQ allocation happens before drivers are probed.
of_pupulate_default_populate() does not know the fact about irqdomain hierarchy.
As a result, interrupts = <0 50 0> in the child_intc,
and interrupts = <0 4> of the I2C are allocated with different virtual
IRQ numbers.
We want to assign the same IRQ number if we want handle them
in the hierarchy IRQ manner.
How can we make it work?
Of course, we can remove the
interrupts = <0 50 0>, <0 51 0>, <0 52 0>, <0 53 0>;
from the child_intc device node.
But, we can not retrieve the IRQ remapping information from DT.
I saw some irqchip implementations and .alloc hook are often
hard-coded in the case.
For example, like this.
static int child_intc_domain_alloc(struct irq_domain *domain,
unsigned int virq, unsigned int nr_irqs, void *arg)
{
....
for (i = 0; i < nr_irqs; i++) {
struct irq_fwspec parent_fwspec;
ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
&priv->chip, priv);
if (ret)
return ret;
/* CAUTION: parent irqchip must be GIC. */
parent_fwspec.fwnode = domain->parent->fwnode;
parent_fwspec.param_count = 3; /*GIC: #interrupt-cells = <3> */
parent_fwspec.param[0] = 0; /* SPI of GIC */
/* HWIRQ=0 of this chip corresponds to HWIRQ=50 of the parent */
parent_fwspec.param[1] = hwirq + 50;
parent_fwspec.param[2] = type;
ret = irq_domain_alloc_irqs_parent(domain, virq, 1,
&parent_fwspec);
if (ret)
return ret;
virq++;
hwirq++;
}
return 0;
}
In order to avoid hard-coding, one possible idea is
to retrieve the IRQ information from DT, like this:
for (i = 0; i < nr_irqs; i++) {
struct of_phandle_args parent_irq;
struct irq_fwspec parent_fwspec;
ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
&priv->chip, priv);
if (ret)
return ret;
/* retrieve interrupt spec from DT */
ret = of_irq_parse_one(irq_domain_get_of_node(domain), hwirq,
&parent_irq);
if (ret)
return ret;
of_phandle_args_to_fwspec(&parent_irq, &parent_fwspec);
ret = irq_domain_alloc_irqs_parent(domain, virq, 1,
&parent_fwspec);
if (ret)
return ret;
virq++;
hwirq++;
}
Some possible solutions:
[1] stop early irq allocation and make it completely on-the-fly
i.e. IRQ are allocated only when drivers explicitly call of_irq_get()
or friends.
This does not address one problem.
If there are many IRQ lines connected between the parent and the child,
interrupts will be very long.
#interrupts = <0 50 0>, <0 51 0>, <0 52 0>, <0 53 0>,
<0 54 0>, <0 55 0>, <0 56 0>, <0 57 0>,
...
This is a mess.
[2] Introduce DT property something like "interrupt-range"
The idea is similar like "ranges" property transforms "reg".
"interrupt-range" is an arbitrary number of
(child irqchip interrupt) (parent irqchip interrupt) (length) triplets.
For example,
interrupt-ranges = <0 0 0 50 0 4>;
This means <0 0>, <0 1>, <0 2>, <0 3> in the child
should be mapped to <0 50 0>, <0 51 0>, <0 52 0>, <0 53 0> in the parent,
respectively.
Actually, "git grep interrupt-ranges" has 3 hits
arch/powerpc/platforms/chrp/setup.c: iranges = of_get_property(np,
"interrupt-ranges", &len);
arch/powerpc/platforms/chrp/setup.c: * The first pair of cells in
interrupt-ranges refers to the
drivers/misc/cxl/of.c: ranges = of_get_property(np, "interrupt-ranges", &len);
I do not know how they are actually used because I see neither DTS
files nor binding documents
that describe it.
That is my rough thought.
Thanks for reading my message.
--
Best Regards
Masahiro Yamada
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
