On 06/24/2017 12:12 AM, Rob Herring wrote:
> On Wed, Jun 21, 2017 at 12:37:34AM +0200, Hauke Mehrtens wrote:
>> From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
>>
>> This adds the initial documentation for the RCU module (a MFD device
>> which provides USB PHYs, reset controllers and more).
>>
>> The RCU register range is used for multiple purposes. Mostly one device
>> uses one or multiple register exclusively, but for some registers some
>> bits are for one driver and some other bits are for a different driver.
>> With this patch all accesses to the RCU registers will go through
>> syscon.
>>
>> Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
>> ---
>> .../devicetree/bindings/mips/lantiq/rcu.txt | 95 ++++++++++++++++++++++
>> 1 file changed, 95 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mips/lantiq/rcu.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt
>> new file mode 100644
>> index 000000000000..9c875f4f3c90
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt
>> @@ -0,0 +1,95 @@
>> +Lantiq XWAY SoC RCU binding
>> +===========================
>> +
>> +This binding describes the RCU (reset controller unit) multifunction device,
>> +where each sub-device has it's own set of registers.
>> +
>> +The RCU register range is used for multiple purposes. Mostly one device
>> +uses one or multiple register exclusively, but for some registers some
>> +bits are for one driver and some other bits are for a different driver.
>> +With this patch all accesses to the RCU registers will go through
>> +syscon.
>> +
>> +
>> +-------------------------------------------------------------------------------
>> +Required properties:
>> +- compatible : The first and second values must be:
>> + "lantiq,xrx200-rcu", "simple-mfd", "syscon"
>> +- reg : The address and length of the system control registers
>> +
>> +
>> +-------------------------------------------------------------------------------
>> +Example of the RCU bindings on a xRX200 SoC:
>> + rcu0: rcu@203000 {
>> + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon";
>> + reg = <0x203000 0x100>;
>> + ranges = <0x0 0x203000 0x100>;
>> + big-endian;
>> +
>> + gphy0: gphy@0 {
>
> unit address should match reg, so "phy@20"
done
>> + compatible = "lantiq,xrx200a2x-gphy";
>> + reg = <0x20 0x4>;
>> +
>> + resets = <&reset0 31 30>, <&reset1 7 7>;
>> + reset-names = "gphy", "gphy2";
>> + lantiq,gphy-mode = <GPHY_MODE_GE>;
>> + };
>> +
>> + gphy1: gphy@1 {
>
> phy@68
done
>> + compatible = "lantiq,xrx200a2x-gphy";
>> + reg = <0x68 0x4>;
>> +
>> + resets = <&reset0 29 28>, <&reset1 6 6>;
>> + reset-names = "gphy", "gphy2";
>> + lantiq,gphy-mode = <GPHY_MODE_GE>;
>> + };
>> +
>> + reset0: reset-controller@0 {
>
> ...@10
done
>> + compatible = "lantiq,xrx200-reset";
>> +
>> + offset-set = <0x10>;
>> + offset-status = <0x14>;
>
> reg = <0x10 8>;
done
>> + #reset-cells = <2>;
>> + };
>> +
>> + reset1: reset-controller@1 {
>> + compatible = "lantiq,xrx200-reset";
>> +
>> + offset-set = <0x48>;
>> + offset-status = <0x24>;
>
> reg = <0x48 4>, <0x24 4>;
done
>> + #reset-cells = <2>;
>> + };
>> +
>> + usb_phy0: usb2-phy@0 {
>> + compatible = "lantiq,xrx200-usb2-phy";
>> + status = "disabled";
>> +
>> + regmap = <&rcu0>;
>
> This should be dropped.
I will get this from the parent device now.
>> + offset-phy = <0x18>;
>> + offset-ana = <0x38>;
>
> Use reg.
There is also one bit used to reset the DSL digital frontend at offset
0x38. This has nothing to do with USB.
>> + resets = <&reset1 4 4>, <&reset0 4 4>;
>> + reset-names = "phy", "ctrl";
>> + #phy-cells = <0>;
>> + };
>> +
>> + usb_phy1: usb2-phy@1 {
>> + compatible = "lantiq,xrx200-usb2-phy";
>> + status = "disabled";
>> +
>> + regmap = <&rcu0>;
>
> Drop.
done
>> + offset-phy = <0x34>;
>> + offset-ana = <0x3C>;
>
> Use reg.
There is also a bits to configure something with the DSL dying gasp at
offset 0x34. This has nothing to do with USB.
>
>> + resets = <&reset1 5 4>, <&reset0 4 4>;
>> + reset-names = "phy", "ctrl";
>> + #phy-cells = <0>;
>> + };
>> +
>> + reboot {
>> + compatible = "syscon-reboot";
>> +
>> + regmap = <&rcu0>;
>
> Drop.
The syscon-reboot driver uses this code to get the regmap:
ctx->map = syscon_regmap_lookup_by_phandle(dev->of_node, "regmap");
This driver was not added by me.
>> + offset = <0x10>;
>> + mask = <0x40000000>;
>> + };
>> + };
>> +
>> --
>> 2.11.0
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
