On 28-06-17 19:02, Tom Levens wrote:
On Wed, 28 Jun 2017, Guenter Roeck wrote:
On Wed, Jun 28, 2017 at 05:29:38PM +0200, Tom Levens wrote:
[ ... ]
Whatever happened to this patch though? It didn't make it to mainline,
otherwise I'd have found it sooner...
I'll have to look it up, but I guess I didn't get an updated version.
As far as I remember I had a working V3 of this patch, but it is
entirely
possible that it was never submitted as I have been busy with other
projects
recently. I'll dig it out and check that it is complete.
FWIW, I don't see it at
https://patchwork.kernel.org/project/linux-hwmon/list/?submitter=171225&state=*
Maybe you were waiting for a reply from Rob. Either case, it might make
sense to only provide valid modes, ie to abstract the mode bits from the
hardware, such as
0 - internal temp only
1 - Tr1
2 - V1
3 - V1-V2
4 - Tr2
5 - V3
6 - V3-V4
7 to 14 - per bit 0..2
Guenter
You are right, there was still an open question about how best to handle
the mode selection in DT.
In the latest version of my patch I have it implemented as an array for
setting the two values, for example:
lltc,meas-mode = <7 3>;
This sets bits [2..0] = 7 and [4..3] = 3. Of course these could be split
into two DT properties, but I was unsure what to name them as both
fields are called "mode" in the datasheet and "mode-43"/"mode-20" (or
similar) is ugly.
With regards to your proposal, it is not clear to me whether the modes
which have the same result are exactly equivalent. Does disabling a
measurement with the mode[4..3] bits really leaves the part in a safe
state for all possible HW connections? With this doubt in my head, I
would prefer to keep the option available to the user to select any
specific mode. But I am open to suggestions.
Well, the input restrictions always apply, so disabling V3 measurement
doesn't imply that you can apply 20V to that input safely now.
I'd suggest to set unused input to plain voltage measurement. That is
"passive" and safe for external components.
So I'd suggest just setting the mode as per device datasheet, I can see
no real advantage in abstracting it away and forcing users to read yet
another document to get it right, e.g.:
lltc,mode = <6>;
As for the input disabling, since I doubt anyone would use it (why
purchase a 4-channel device and use only 2), just add two booleans, e.g.
"disable-inputs-34" and "disable-inputs-12" which set the command bits
appropriately, and change the mode such that the disabled inputs are
voltage readout only.
A case could even be made for changing mode at runtime. This allows
using it to measure both current and voltage on two inputs, by reading
V1, and V3, and then switch mode to obtain (accurate) V1-V2 and V4-V3.
That might be a viable way to handle not setting the mode at all. If the
mode can be selected via sysfs, the driver can keep the device in a
"safe" mode until the mode has been selected.
Mike, if you would like to test it, the latest version of my code is here:
https://github.com/levens/ltc2990/blob/dev/drivers/hwmon/ltc2990.c
Sure, I even have a board with 2 of these devices now :)
--
Mike Looijmans
Kind regards,
Mike Looijmans
System Expert
TOPIC Products
Materiaalweg 4, NL-5681 RJ Best
Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
E-mail: mike.looijmans@xxxxxxxxxxxxxxxxx
Website: www.topicproducts.com
Please consider the environment before printing this e-mail
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
