On Sat, 2017-06-10 at 23:57 +0200, Heiner Kallweit wrote:
> Add a driver supporting the GPIO interrupt controller on certain
> Amlogic meson SoC's.
>
> Signed-off-by: Heiner Kallweit <hkallweit1@xxxxxxxxx>
> ---
> v5:
> - changed Kconfig entry based on Neil's suggestion
> - added authors
> - extended explanation why 2 * n hwirqs are used
> v6:
> - change DT property parent-interrupts to interrupts
> v7:
> - no changes
> ---
> drivers/irqchip/Kconfig | 5 +
> drivers/irqchip/Makefile | 1 +
> drivers/irqchip/irq-meson-gpio.c | 295
> +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 301 insertions(+)
> create mode 100644 drivers/irqchip/irq-meson-gpio.c
>
> diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
> index 478f8ace..bdc86e14 100644
> --- a/drivers/irqchip/Kconfig
> +++ b/drivers/irqchip/Kconfig
> @@ -301,3 +301,8 @@ config QCOM_IRQ_COMBINER
> help
> Say yes here to add support for the IRQ combiner devices embedded
> in Qualcomm Technologies chips.
> +
> +config MESON_GPIO_INTC
> + bool
> + depends on ARCH_MESON
> + default y
> diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
> index b64c59b8..1be482bd 100644
> --- a/drivers/irqchip/Makefile
> +++ b/drivers/irqchip/Makefile
> @@ -76,3 +76,4 @@ obj-$(CONFIG_EZNPS_GIC) += irq-
> eznps.o
> obj-$(CONFIG_ARCH_ASPEED) += irq-aspeed-vic.o
> obj-$(CONFIG_STM32_EXTI) += irq-stm32-exti.o
> obj-$(CONFIG_QCOM_IRQ_COMBINER) += qcom-irq-combiner.o
> +obj-$(CONFIG_MESON_GPIO_INTC) += irq-meson-gpio.o
> diff --git a/drivers/irqchip/irq-meson-gpio.c b/drivers/irqchip/irq-meson-
> gpio.c
> new file mode 100644
> index 00000000..925d00c2
> --- /dev/null
> +++ b/drivers/irqchip/irq-meson-gpio.c
> @@ -0,0 +1,295 @@
> +/*
> + * Amlogic Meson GPIO IRQ chip driver
> + *
> + * Copyright (c) 2015 Endless Mobile, Inc.
> + * Author: Carlo Caione <carlo@xxxxxxxxxxxx>
> + * Copyright (c) 2016 BayLibre, SAS.
> + * Author: Jerome Brunet <jbrunet@xxxxxxxxxxxx>
> + * Copyright (c) 2017 Heiner Kallweit <hkallweit1@xxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation, version 2.
> + */
> +
> +#include <linux/device.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqchip.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_address.h>
> +#include <linux/regmap.h>
> +
> +#define REG_EDGE_POL 0x00
> +#define REG_PIN_03_SEL 0x04
> +#define REG_PIN_47_SEL 0x08
> +#define REG_FILTER_SEL 0x0c
> +
> +#define REG_EDGE_POL_MASK(x) (BIT(x) | BIT(16 + (x)))
> +#define REG_EDGE_POL_EDGE(x) BIT(x)
> +#define REG_EDGE_POL_LOW(x) BIT(16 + (x))
> +
> +#define MAX_PARENT_IRQ_NUM 8
> +
> +/* maximum number of GPIO IRQs on supported platforms */
> +#define MAX_NUM_GPIO_IRQ 133
Comment on V6 still applies here. 133 being the max on gxbb does not make it the
max on the other supported chipset.
Review from october suggested to put this value in DT.
> +
> +/*
> + * In case of IRQ_TYPE_EDGE_BOTH we need two parent interrupts, one for each
> + * edge. That's due to HW constraints.
> + * We use format 2 * GPIO_HWIRQ +(0|1) for the hwirq, so we can have one
> + * GPIO_HWIRQ twice and derive the GPIO_HWIRQ from hwirq by shifting hwirq
> + * one bit to the right.
> + */
> +#define NUM_GPIO_HWIRQ (2 * MAX_NUM_GPIO_IRQ)
????
> +
> +struct meson_irq_slot {
> + unsigned int irq;
> + unsigned int owner;
> +};
> +
> +struct meson_data {
> + struct regmap *regmap;
> + struct meson_irq_slot slots[MAX_PARENT_IRQ_NUM];
> + unsigned int num_slots;
> + struct mutex lock;
> +};
> +
> +static int meson_alloc_irq_slot(struct meson_data *md, unsigned int virq)
> +{
> + int i, slot = -ENOSPC;
> +
> + mutex_lock(&md->lock);
> +
> + for (i = 0; i < md->num_slots && slot < 0; i++)
> + if (!md->slots[i].owner) {
> + md->slots[i].owner = virq;
> + slot = i;
> + }
> +
> + mutex_unlock(&md->lock);
> +
> + return slot;
> +}
> +
> +static void meson_free_irq_slot(struct meson_data *md, unsigned int virq)
> +{
> + int i;
> +
> + mutex_lock(&md->lock);
> +
> + for (i = 0; i < md->num_slots; i++)
> + if (md->slots[i].owner == virq) {
> + md->slots[i].owner = 0;
> + break;
> + }
> +
> + mutex_unlock(&md->lock);
> +}
> +
> +static int meson_find_irq_slot(struct meson_data *md, unsigned int virq)
> +{
> + int i, slot = -EINVAL;
> +
> + mutex_lock(&md->lock);
> +
> + for (i = 0; i < md->num_slots && slot < 0; i++)
> + if (md->slots[i].owner == virq)
> + slot = i;
> +
> + mutex_unlock(&md->lock);
> +
> + return slot;
> +}
> +
> +static void meson_set_hwirq(struct meson_data *md, int idx, unsigned int
> hwirq)
> +{
> + int reg = idx > 3 ? REG_PIN_47_SEL : REG_PIN_03_SEL;
> + int shift = 8 * (idx % 4);
> +
> + regmap_update_bits(md->regmap, reg, 0xff << shift,
> + hwirq << shift);
> +}
> +
> +static void meson_irq_set_hwirq(struct irq_data *data, unsigned int hwirq)
> +{
> + struct meson_data *md = data->domain->host_data;
> + int slot = meson_find_irq_slot(md, data->irq);
> +
> + if (slot >= 0)
> + meson_set_hwirq(md, slot, hwirq);
> +}
> +
> +static int meson_irq_set_type(struct irq_data *data, unsigned int type)
> +{
> + struct meson_data *md = data->domain->host_data;
> + int slot;
> + unsigned int val = 0;
> +
> + if (type == IRQ_TYPE_EDGE_BOTH)
> + return -EINVAL;
> +
> + slot = meson_find_irq_slot(md, data->irq);
> + if (slot < 0)
> + return slot;
> +
> + if (type & IRQ_TYPE_EDGE_BOTH)
> + val |= REG_EDGE_POL_EDGE(slot);
> +
> + if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING))
> + val |= REG_EDGE_POL_LOW(slot);
> +
> + regmap_update_bits(md->regmap, REG_EDGE_POL,
> + REG_EDGE_POL_MASK(slot), val);
> +
> + if (type & IRQ_TYPE_EDGE_BOTH)
> + val = IRQ_TYPE_EDGE_RISING;
> + else
> + val = IRQ_TYPE_LEVEL_HIGH;
> +
> + return irq_chip_set_type_parent(data, val);
> +}
> +
> +static unsigned int meson_irq_startup(struct irq_data *data)
> +{
> + irq_chip_unmask_parent(data);
> + /*
> + * An extra bit was added to allow having the same gpio hwirq twice
> + * for handling IRQ_TYPE_EDGE_BOTH. Remove this bit to get the
> + * gpio hwirq.
> + */
> + meson_irq_set_hwirq(data, data->hwirq >> 1);
Comments from v6 still applies here, and this has nothing to do with the so-
called percentage of niceness - whatever this means.
This is an interrupt controller, a critical part of the system. It has be
correct.
Multiplying the number of IRQ lines and so changing the interface is not
correct.
DT is OS independent, property should not be os-specific, let alone driver-
hacked specific.
Interfaces, including DT, are important. These are supposed to be stable. We
don't to change the irq numbers in every dts because "yeahhh we found another
way!"
So yes, the corner cases should be covered, what drives you is not the matter
here. If you have a critical need for this, then feel free to apply the patch to
your kernel, no one is stopping you. If it goes upstream, people should be able
to understand it and trust it, identified corner cases should be covered.
> +
> + return 0;
> +}
> +
> +static void meson_irq_shutdown(struct irq_data *data)
> +{
> + meson_irq_set_hwirq(data, 0xff);
> + irq_chip_mask_parent(data);
> +}
> +
> +static struct irq_chip meson_irq_chip = {
> + .name = "meson_gpio_intc",
> + .irq_set_type = meson_irq_set_type,
> + .irq_eoi = irq_chip_eoi_parent,
> + .irq_mask = irq_chip_mask_parent,
> + .irq_unmask = irq_chip_unmask_parent,
> + .irq_startup = meson_irq_startup,
> + .irq_shutdown = meson_irq_shutdown,
> + .irq_set_affinity = irq_chip_set_affinity_parent,
> +};
> +
> +static int meson_irq_alloc(struct irq_domain *d, unsigned int virq,
> + unsigned int nr_irqs, void *data)
> +{
> + struct irq_fwspec parent_fwspec, *fwspec = data;
> + struct meson_data *md = d->host_data;
> + irq_hw_number_t hwirq;
> + int ret, slot;
> +
> + slot = meson_alloc_irq_slot(md, virq);
> + if (slot < 0)
> + return slot;
> +
> + hwirq = fwspec->param[0];
> + irq_domain_set_hwirq_and_chip(d, virq, hwirq, &meson_irq_chip, NULL);
> +
> + parent_fwspec.fwnode = d->parent->fwnode;
> + parent_fwspec.param_count = 3;
> + parent_fwspec.param[0] = 0; /* SPI */
> + parent_fwspec.param[1] = md->slots[slot].irq;
> + parent_fwspec.param[2] = IRQ_TYPE_NONE;
> +
> + ret = irq_domain_alloc_irqs_parent(d, virq, nr_irqs, &parent_fwspec);
> + if (ret)
> + meson_free_irq_slot(md, virq);
> +
> + return ret;
> +}
> +
> +static void meson_irq_free(struct irq_domain *d, unsigned int virq,
> + unsigned int nr_irqs)
> +{
> + struct meson_data *md = d->host_data;
> +
> + irq_domain_free_irqs_common(d, virq, nr_irqs);
> + meson_free_irq_slot(md, virq);
> +}
> +
> +static const struct irq_domain_ops meson_irq_ops = {
> + .alloc = meson_irq_alloc,
> + .free = meson_irq_free,
> + .xlate = irq_domain_xlate_twocell,
> +};
> +
> +static int meson_get_irqs(struct meson_data *md, struct device_node *node)
> +{
> + int ret, i;
> + u32 irq;
> +
> + for (i = 0; i < MAX_PARENT_IRQ_NUM; i++) {
> + ret = of_property_read_u32_index(node, "interrupts", i,
> &irq);
> + if (ret)
> + break;
> + md->slots[i].irq = irq;
> + }
> +
> + md->num_slots = i;
> +
> + return i ? 0 : -EINVAL;
> +}
> +
> +static const struct regmap_config meson_regmap_config = {
> + .reg_bits = 32,
> + .reg_stride = 4,
> + .val_bits = 32,
> + .max_register = REG_FILTER_SEL,
> +};
> +
> +static int __init meson_gpio_irq_init(struct device_node *node,
> + struct device_node *parent)
> +{
> + struct irq_domain *meson_irq_domain, *parent_domain;
> + struct meson_data *md;
> + void __iomem *io_base;
> + int ret;
> +
> + md = kzalloc(sizeof(*md), GFP_KERNEL);
> + if (!md)
> + return -ENOMEM;
> +
> + mutex_init(&md->lock);
> +
> + io_base = of_iomap(node, 0);
> + if (!io_base)
> + return -EINVAL;
> +
> + md->regmap = regmap_init_mmio(NULL, io_base, &meson_regmap_config);
> + if (IS_ERR(md->regmap))
> + return PTR_ERR(md->regmap);
> +
> + /* initialize to IRQ_TYPE_LEVEL_HIGH */
> + regmap_write(md->regmap, REG_EDGE_POL, 0);
> + /* disable all GPIO interrupt sources */
> + regmap_write(md->regmap, REG_PIN_03_SEL, 0xffffffff);
> + regmap_write(md->regmap, REG_PIN_47_SEL, 0xffffffff);
> + /* disable filtering */
> + regmap_write(md->regmap, REG_FILTER_SEL, 0);
> +
> + ret = meson_get_irqs(md, node);
> + if (ret)
> + return ret;
> +
> + parent_domain = irq_find_host(parent);
> + if (!parent_domain)
> + return -ENXIO;
> +
> + meson_irq_domain = irq_domain_add_hierarchy(parent_domain, 0,
> + NUM_GPIO_HWIRQ, node,
> + &meson_irq_ops, md);
> + return meson_irq_domain ? 0 : -EINVAL;
> +}
> +
> +IRQCHIP_DECLARE(meson_gpio_irq, "amlogic,meson-gpio-intc",
> meson_gpio_irq_init);
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
