Maxime,
On 06/06/2017 14:04, Maxime Ripard wrote:
On Tue, Jun 06, 2017 at 10:03:48AM +0200, Mylene Josserand wrote:
+static int cyttsp5_hid_output_bl_launch_app(struct cyttsp5 *ts)
+{
+ int rc, t;
+ u8 cmd[HID_OUTPUT_BL_LAUNCH_APP];
+ u16 crc;
+
+ mutex_lock(&ts->system_lock);
+ ts->hid_cmd_state = HID_OUTPUT_BL_LAUNCH_APP + 1;
+ mutex_unlock(&ts->system_lock);
+
+ cmd[0] = LOW_BYTE(HID_OUTPUT_BL_LAUNCH_APP_SIZE);
+ cmd[1] = HI_BYTE(HID_OUTPUT_BL_LAUNCH_APP_SIZE);
+ cmd[2] = HID_BL_OUTPUT_REPORT_ID;
+ cmd[3] = 0x0; /* Reserved */
+ cmd[4] = HID_OUTPUT_BL_SOP;
+ cmd[5] = HID_OUTPUT_BL_LAUNCH_APP;
+ cmd[6] = 0x0; /* Low bytes of data */
+ cmd[7] = 0x0; /* Hi bytes of data */
+ crc = cyttsp5_compute_crc(&cmd[4], 4);
+ cmd[8] = LOW_BYTE(crc);
+ cmd[9] = HI_BYTE(crc);
+ cmd[10] = HID_OUTPUT_BL_EOP;
+
+ rc = cyttsp5_write(ts, HID_OUTPUT_REG, cmd,
+ HID_OUTPUT_BL_LAUNCH_APP_SIZE);
It seems like you'll send HID_OUTPUT_BL_LAUNCH_APP_SIZE twice here,
once as setup in cyttsp5_write, and once in the buffer you want to
send. Is that on purpose?
I am not sure to see the second time it is sent. What do you mean by "as
setup in cyttsp5_write"? Anyway, the size is needed in the buffer of the
frame.
Nevermind, I confused the HID_OUTPUT_BL_LAUNCH_APP_SIZE with the
register, my bad.
No problem.
+ /* Call platform init function */
+ ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ts->reset_gpio)) {
+ rc = PTR_ERR(ts->reset_gpio);
+ dev_err(dev, "Failed to request reset gpio, error %d\n", rc);
+ return rc;
+ }
+
+ /* Need a delay to have device up */
+ msleep(20);
In the case where the device has already been out of reset, this means
that this alone is not sufficient to reset it and bring it out of
reset, which also means that you do not have any guarantee on the
current state of the device. I'm not sure how it would impact the
proper operations though.
Okay. A reset frame can be sent to perform a "software
reset". Should I add it on startup to be in a "known behavior"?
I guess you'd be safer just getting the GPIO with the low level by
default, and then changing to high. That way you know that you went
through a reset state, before bringing up the device.
Okay, I will update the driver, thanks!
+ ts->input = input_allocate_device();
+ if (!ts->input) {
+ dev_err(dev, "%s: Error, failed to allocate input device\n",
+ __func__);
+ rc = -ENODEV;
+ goto error_startup;
+ }
In error_startup, you never uninitialize the device. Given your
comment in cyttsp5_startup, this means that you might end up in a
situation where your driver probes again with the device initialized
and no longer in a bootloader mode, which is likely to cause some
error.
Putting the call to cyttsp5_startup later will make you less likely to
fail (especially because of the DT parsing), and putting the device
back into reset will probably address the issue once and for all.
Hm, I am not sure to understand what you want to say, here.
Could you explain me more what you have in mind?
I meant to say that there was still an issue with the reset here, and
moving the DT parsing code further would ease the reset operation.
Okay
Notice that the DT parsing uses a sysinfo's variable (si->num_btns)
which is retrieved in the startup function (thanks to
get_sysinfo). So, currently, it is not possible to move the startup
function after the DT parsing.
Can't that be made the other way around? You parse the number of
buttons in the DT, and check the consistency with the hardware?
It could be possible but currently, it was designed to enable every
button from hardware's configuration and DT binding was just a way to
customize button's keycode (default is KEY_RESERVED).
If I base it on the DT, it means that some buttons could never be
reported (such as deactivated) because they will not be present in the
DT. I am not sure if it is the behavior we want. What do you think?
Best regards,
--
Mylène Josserand, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html