On Fri, 02 Jun 2017, Valentin Sitdikov wrote: > This patch adds documentation for the max7360 bindings. > The max7360 is multifunctional device containing GPIO, keypad, PWM and rotary encoder submodules. > > Signed-off-by: Andrei Dranitca <Andrei_Dranitca@xxxxxxxxxx> > Signed-off-by: Valentin Sitdikov <valentin_sitdikov@xxxxxxxxxx> > --- > Documentation/devicetree/bindings/mfd/max7360.txt | 74 +++++++++++++++++++++++ > 1 file changed, 74 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/max7360.txt > > diff --git a/Documentation/devicetree/bindings/mfd/max7360.txt b/Documentation/devicetree/bindings/mfd/max7360.txt > new file mode 100644 > index 0000000..a38ca9e > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/max7360.txt > @@ -0,0 +1,74 @@ > +* Maxim MAX7360 multi-function device Multi-Function Device > +The Maxim MAX7360 is a multifunction device which includes Multi-Function Device > +64 key switches, eight LED drivers/GPIOs, PWM intensity control, s/eight/8/ > +and rotary switch control. > + > +Required properties: > +- compatible: Should be the following: "maxim,max7360" > +- reg: Specifies the i2c slave address of the max7360 block. I2C > + It can be 0x38, 0x3a, 0x3c or 0x3e IIUC. > + > +Optional properties: > +- interrupt-parent: Specifies the phandle of the interrupt controller to which > + the interrupts from MAX7360 are routed to. Either use a full-stop, or don't, but please do not mix. > +- interrupts: list of IRQ lines specifiers > +- interrupt-names: list of "inti" and "intk" > +- interrupt-controller: Identifies the device as an interrupt controller. > +- #interrupt-cells : Number of cells to encode an interrupt source, shall be 1. Tab these out. > +Required properties: > +- compatible: Should be the following: "maxim,max7360" > +- reg: Specifies the i2c slave address of the max7360 block. > + It can be 0x38, 0x3a, 0x3c or 0x3e IIUC. > + > +Optional properties: > +- interrupt-parent: Specifies the phandle of the interrupt controller to which > + the interrupts from MAX7360 are routed to. > +- interrupts: list of IRQ lines specifiers > +- interrupt-names: list of "inti" and "intk" > +- interrupt-controller: Identifies the device as an interrupt controller. > +- #interrupt-cells : Number of cells to encode an interrupt source, shall be 1. Descriptions should *all* start with an upper case character. > +Examples: > + > +Without subnodes: > + max7360@38 { > + compatible = "maxim,max7360"; > + reg = <0x38>; > + interrupt-parent = <&gpio1>; > + interrupts = <23 IRQ_TYPE_LEVEL_LOW>, <23 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "inti", "intk"; > + interrupt-controller; > + #interrupt-cells = <0x1>; > + Remove this line. > + }; > + > +With subnodes: > + max7360@38 { > + compatible = "maxim,max7360"; > + reg = <0x38>; > + interrupt-parent = <&gpio1>; > + interrupts = <23 IRQ_TYPE_LEVEL_LOW>, <23 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "inti", "intk"; > + interrupt-controller; > + #interrupt-cells = <0x1>; > + > + gpio { > + compatible = "maxim,max7360-gpio"; > + gpio-controller; > + #gpio-cells = <0x2>; > + interrupt-controller; > + #interrupt-cells = <0x2>; > + interrupts = <0>; > + }; > + > + keypad { > + compatible = "maxim,max7360-keypad"; > + maxim,debounce_reg = /bits/ 8 <0xef>; > + maxim,ports_reg = /bits/ 8 <0xae>; > + linux,keymap = < MATRIX_KEY(0, 0, KEY_F5) > + MATRIX_KEY(1, 0, KEY_F4) >; > + keypad,num-rows = <2>; > + keypad,num-columns = <1>; > + interrupts = <1>; > + }; > + > + pwm { > + compatible = "maxim,max7360-pwm"; > + #pwm-cells = <0x2>; > + }; > + > + rotary-encoder { > + compatible = "maxim,max7360-rotary"; > + interrupts = <2>; > + }; > + > + }; -- Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html