This patch adds support for stingray SATA phy in the
SATA BRCM phy driver.
Signed-off-by: Srinath Mannam <srinath.mannam@xxxxxxxxxxxx>
---
drivers/phy/phy-brcm-sata.c | 73 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
index ccbc3d9..e6544c8 100644
--- a/drivers/phy/phy-brcm-sata.c
+++ b/drivers/phy/phy-brcm-sata.c
@@ -46,6 +46,7 @@ enum brcm_sata_phy_version {
BRCM_SATA_PHY_STB_40NM,
BRCM_SATA_PHY_IPROC_NS2,
BRCM_SATA_PHY_IPROC_NSP,
+ BRCM_SATA_PHY_IPROC_SR,
};
struct brcm_sata_port {
@@ -81,12 +82,17 @@ enum sata_phy_regs {
PLL_ACTRL2 = 0x8b,
PLL_ACTRL2_SELDIV_MASK = 0x1f,
PLL_ACTRL2_SELDIV_SHIFT = 9,
+ PLL_ACTRL6 = 0x86,
PLL1_REG_BANK = 0x060,
PLL1_ACTRL2 = 0x82,
PLL1_ACTRL3 = 0x83,
PLL1_ACTRL4 = 0x84,
+ TX_REG_BANK = 0x070,
+ TX_ACTRL0 = 0x80,
+ TX_ACTRL0_TXPOL_FLIP = BIT(6),
+
OOB_REG_BANK = 0x150,
OOB1_REG_BANK = 0x160,
OOB_CTRL1 = 0x80,
@@ -347,6 +353,68 @@ static int brcm_nsp_sata_init(struct brcm_sata_port *port)
return 0;
}
+/* SR PHY PLL0 registers */
+#define SR_PLL0_ACTRL6_MAGIC 0xa
+
+/* SR PHY PLL1 registers */
+#define SR_PLL1_ACTRL2_MAGIC 0x32
+#define SR_PLL1_ACTRL3_MAGIC 0x2
+#define SR_PLL1_ACTRL4_MAGIC 0x3e8
+
+static int brcm_sr_sata_init(struct brcm_sata_port *port)
+{
+ struct brcm_sata_phy *priv = port->phy_priv;
+ struct device *dev = port->phy_priv->dev;
+ void __iomem *base = priv->phy_base;
+ unsigned int val, try;
+
+ /* Configure PHY PLL register bank 1 */
+ val = SR_PLL1_ACTRL2_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val);
+ val = SR_PLL1_ACTRL3_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val);
+ val = SR_PLL1_ACTRL4_MAGIC;
+ brcm_sata_phy_wr(base, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val);
+
+ /* Configure PHY PLL register bank 0 */
+ val = SR_PLL0_ACTRL6_MAGIC;
+ brcm_sata_phy_wr(base, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val);
+
+ /* Wait for PHY PLL lock by polling pll_lock bit */
+ try = 50;
+ do {
+ val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
+ BLOCK0_XGXSSTATUS);
+ if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)
+ break;
+ msleep(20);
+ try--;
+ } while (try);
+
+ if ((val & BLOCK0_XGXSSTATUS_PLL_LOCK) == 0) {
+ /* PLL did not lock; give up */
+ dev_err(dev, "port%d PLL did not lock\n", port->portnum);
+ return -ETIMEDOUT;
+ }
+
+ /* Invert Tx polarity */
+ brcm_sata_phy_wr(base, TX_REG_BANK, TX_ACTRL0,
+ ~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP);
+
+ /* Configure OOB control to handle 100MHz reference clock */
+ val = ((0xc << OOB_CTRL1_BURST_MAX_SHIFT) |
+ (0x4 << OOB_CTRL1_BURST_MIN_SHIFT) |
+ (0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) |
+ (0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT));
+ brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL1, 0x0, val);
+ val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) |
+ (0x2 << OOB_CTRL2_BURST_CNT_SHIFT) |
+ (0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT));
+ brcm_sata_phy_wr(base, OOB_REG_BANK, OOB_CTRL2, 0x0, val);
+
+ return 0;
+}
+
static int brcm_sata_phy_init(struct phy *phy)
{
int rc;
@@ -363,6 +431,9 @@ static int brcm_sata_phy_init(struct phy *phy)
case BRCM_SATA_PHY_IPROC_NSP:
rc = brcm_nsp_sata_init(port);
break;
+ case BRCM_SATA_PHY_IPROC_SR:
+ rc = brcm_sr_sata_init(port);
+ break;
default:
rc = -ENODEV;
}
@@ -384,6 +455,8 @@ static const struct of_device_id brcm_sata_phy_of_match[] = {
.data = (void *)BRCM_SATA_PHY_IPROC_NS2 },
{ .compatible = "brcm,iproc-nsp-sata-phy",
.data = (void *)BRCM_SATA_PHY_IPROC_NSP },
+ { .compatible = "brcm,iproc-sr-sata-phy",
+ .data = (void *)BRCM_SATA_PHY_IPROC_SR },
{},
};
MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
