On 05/22/2017 07:30 AM, John Crispin wrote:
>
>
> On 21/05/17 15:09, Hauke Mehrtens wrote:
>> From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
>>
>> This allows using the xbar driver on ARX300 based SoCs which require the
>> same xbar setup as the xRX200 chipsets because the xbar driver
>> initialization is not guarded by an xRX200 specific
>> of_machine_is_compatible condition anymore. Additionally the new driver
>> takes a syscon phandle to configure the XBAR endianness bits in RCU
>> (before this was done in arch/mips/lantiq/xway/reset.c and also
>> guarded by an VRX200 specific if-statement).
>>
>> Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
>> ---
>> .../devicetree/bindings/mips/lantiq/xbar.txt | 24 +++++
>> MAINTAINERS | 1 +
>> arch/mips/lantiq/xway/reset.c | 4 -
>> arch/mips/lantiq/xway/sysctrl.c | 41 ---------
>> drivers/soc/Makefile | 1 +
>> drivers/soc/lantiq/Makefile | 1 +
>> drivers/soc/lantiq/xbar.c | 101
>> +++++++++++++++++++++
>> 7 files changed, 128 insertions(+), 45 deletions(-)
>> create mode 100644
>> Documentation/devicetree/bindings/mips/lantiq/xbar.txt
>> create mode 100644 drivers/soc/lantiq/Makefile
>> create mode 100644 drivers/soc/lantiq/xbar.c
>>
>> diff --git a/Documentation/devicetree/bindings/mips/lantiq/xbar.txt
>> b/Documentation/devicetree/bindings/mips/lantiq/xbar.txt
>> new file mode 100644
>> index 000000000000..7e1ea5299744
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mips/lantiq/xbar.txt
>> @@ -0,0 +1,24 @@
>> +Lantiq XWAY SoC XBAR binding
>> +============================
>> +
>> +
>> +-------------------------------------------------------------------------------
>>
>> +Required properties:
>> +- compatible : Should be one of
>> + "lantiq,xbar-xway"
>> + "lantiq,xbar-xrx200"
>> +- reg : The address and length of the XBAR registers
>> +
>> +Optional properties:
>> +- lantiq,rcu-syscon : A phandle and offset to the endianness
>> configuration
>> + registers in the RCU module
>> +
>> +
>> +-------------------------------------------------------------------------------
>>
>> +Example for the XBAR on the xRX200 SoCs:
>> + xbar0: xbar@400000 {
>> + compatible = "lantiq,xbar-xway";
>> + reg = <0x400000 0x1000>;
>> + big-endian;
>> + lantiq,rcu-syscon = <&rcu0 0x4c>;
>> + };
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index f7d568b8f133..11c33f7d63ba 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -7434,6 +7434,7 @@ M: John Crispin <john@xxxxxxxxxxx>
>> L: linux-mips@xxxxxxxxxxxxxx
>> S: Maintained
>> F: arch/mips/lantiq
>> +F: drivers/soc/lantiq
>> LAPB module
>> L: linux-x25@xxxxxxxxxxxxxxx
>> diff --git a/arch/mips/lantiq/xway/reset.c
>> b/arch/mips/lantiq/xway/reset.c
>> index 83fd65d76e81..b6752c95a600 100644
>> --- a/arch/mips/lantiq/xway/reset.c
>> +++ b/arch/mips/lantiq/xway/reset.c
>> @@ -373,10 +373,6 @@ static int __init mips_reboot_setup(void)
>> of_machine_is_compatible("lantiq,vr9"))
>> ltq_usb_init();
>> - if (of_machine_is_compatible("lantiq,vr9"))
>> - ltq_rcu_w32(ltq_rcu_r32(RCU_AHB_ENDIAN) | RCU_VR9_BE_AHB1S,
>> - RCU_AHB_ENDIAN);
>> -
>> _machine_restart = ltq_machine_restart;
>> _machine_halt = ltq_machine_halt;
>> pm_power_off = ltq_machine_power_off;
>> diff --git a/arch/mips/lantiq/xway/sysctrl.c
>> b/arch/mips/lantiq/xway/sysctrl.c
>> index 95bec460b651..706639a343bc 100644
>> --- a/arch/mips/lantiq/xway/sysctrl.c
>> +++ b/arch/mips/lantiq/xway/sysctrl.c
>> @@ -145,15 +145,7 @@ static u32 pmu_clk_cr_b[] = {
>> #define pmu_w32(x, y) ltq_w32((x), pmu_membase + (y))
>> #define pmu_r32(x) ltq_r32(pmu_membase + (x))
>> -#define XBAR_ALWAYS_LAST 0x430
>> -#define XBAR_FPI_BURST_EN BIT(1)
>> -#define XBAR_AHB_BURST_EN BIT(2)
>> -
>> -#define xbar_w32(x, y) ltq_w32((x), ltq_xbar_membase + (y))
>> -#define xbar_r32(x) ltq_r32(ltq_xbar_membase + (x))
>> -
>> static void __iomem *pmu_membase;
>> -static void __iomem *ltq_xbar_membase;
>> void __iomem *ltq_cgu_membase;
>> void __iomem *ltq_ebu_membase;
>> @@ -293,16 +285,6 @@ static void pci_ext_disable(struct clk *clk)
>> ltq_cgu_w32((1 << 31) | (1 << 30), pcicr);
>> }
>> -static void xbar_fpi_burst_disable(void)
>> -{
>> - u32 reg;
>> -
>> - /* bit 1 as 1 --burst; bit 1 as 0 -- single */
>> - reg = xbar_r32(XBAR_ALWAYS_LAST);
>> - reg &= ~XBAR_FPI_BURST_EN;
>> - xbar_w32(reg, XBAR_ALWAYS_LAST);
>> -}
>> -
>> /* enable a clockout source */
>> static int clkout_enable(struct clk *clk)
>> {
>> @@ -459,26 +441,6 @@ void __init ltq_soc_init(void)
>> if (!pmu_membase || !ltq_cgu_membase || !ltq_ebu_membase)
>> panic("Failed to remap core resources");
>> - if (of_machine_is_compatible("lantiq,vr9")) {
>> - struct resource res_xbar;
>> - struct device_node *np_xbar =
>> - of_find_compatible_node(NULL, NULL,
>> - "lantiq,xbar-xway");
>> -
>> - if (!np_xbar)
>> - panic("Failed to load xbar nodes from devicetree");
>> - if (of_address_to_resource(np_xbar, 0, &res_xbar))
>> - panic("Failed to get xbar resources");
>> - if (!request_mem_region(res_xbar.start,
>> resource_size(&res_xbar),
>> - res_xbar.name))
>> - panic("Failed to get xbar resources");
>> -
>> - ltq_xbar_membase = ioremap_nocache(res_xbar.start,
>> - resource_size(&res_xbar));
>> - if (!ltq_xbar_membase)
>> - panic("Failed to remap xbar resources");
>> - }
>> -
>> /* make sure to unprotect the memory region where flash is
>> located */
>> ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS,
>> LTQ_EBU_BUSCON0);
>> @@ -605,7 +567,4 @@ void __init ltq_soc_init(void)
>> clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
>> clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0);
>> }
>> -
>> - if (of_machine_is_compatible("lantiq,vr9"))
>> - xbar_fpi_burst_disable();
>> }
>> diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
>> index 824b44281efa..009b5de74a24 100644
>> --- a/drivers/soc/Makefile
>> +++ b/drivers/soc/Makefile
>> @@ -8,6 +8,7 @@ obj-$(CONFIG_ARCH_DOVE) += dove/
>> obj-$(CONFIG_MACH_DOVE) += dove/
>> obj-y += fsl/
>> obj-$(CONFIG_ARCH_MXC) += imx/
>> +obj-$(CONFIG_SOC_XWAY) += lantiq/
>> obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
>> obj-$(CONFIG_ARCH_QCOM) += qcom/
>> obj-$(CONFIG_ARCH_RENESAS) += renesas/
>> diff --git a/drivers/soc/lantiq/Makefile b/drivers/soc/lantiq/Makefile
>> new file mode 100644
>> index 000000000000..7411bd23d58e
>> --- /dev/null
>> +++ b/drivers/soc/lantiq/Makefile
>> @@ -0,0 +1 @@
>> +obj-y += xbar.o
>> diff --git a/drivers/soc/lantiq/xbar.c b/drivers/soc/lantiq/xbar.c
>> new file mode 100644
>> index 000000000000..89590e189efc
>> --- /dev/null
>> +++ b/drivers/soc/lantiq/xbar.c
>> @@ -0,0 +1,101 @@
>> +/*
>> + * This program is free software; you can redistribute it and/or
>> modify it
>> + * under the terms of the GNU General Public License version 2 as
>> published
>> + * by the Free Software Foundation.
>> + *
>> + * Copyright (C) 2011-2015 John Crispin <blogic@xxxxxxxxxxx>
>
> Hi Hauke,
>
> my openwrt email addr is no longer valid. please use my phrozen.org one.
>
> John
Sorry, I fixed that in all patches.
Hauke
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
