On Mon, May 22, 2017 at 11:15:17AM +0200, Quentin Schulz wrote:
> Some PHY require to wait for a bit after the reset GPIO has been
> toggled. This adds support for the DT property `phy-reset-post-delay`
> which gives the delay in milliseconds to wait after reset.
>
> If the DT property is not given, no delay is observed. Post reset delay
> greater than 1000ms are invalid and are default to 1ms.
Hi Quentin
If it is invalid, please return -EINVAL.
> Signed-off-by: Quentin Schulz <quentin.schulz@xxxxxxxxxxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/net/fsl-fec.txt | 5 +++++
> drivers/net/ethernet/freescale/fec_main.c | 17 +++++++++++++++--
> 2 files changed, 20 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
> index a1e3693cca16..8795e8ca5793 100644
> --- a/Documentation/devicetree/bindings/net/fsl-fec.txt
> +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
> @@ -15,6 +15,11 @@ Optional properties:
> - phy-reset-active-high : If present then the reset sequence using the GPIO
> specified in the "phy-reset-gpios" property is reversed (H=reset state,
> L=operation state).
> +- phy-reset-post-delay : Post reset delay in milliseconds. If present then
> + a delay of phy-reset-post-delay milliseconds will be observed after the
> + phy-reset-gpios has been toggled. Can be omitted thus no delay is
> + observed. Delay is in range of 1ms to 1000ms. If given delay is higher
> + than 1000ms, 1ms delay is done instead.
> - phy-supply : regulator that powers the Ethernet PHY.
> - phy-handle : phandle to the PHY device connected to this device.
> - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
> diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
> index 56a563f90b0b..00a7fd0bcd59 100644
> --- a/drivers/net/ethernet/freescale/fec_main.c
> +++ b/drivers/net/ethernet/freescale/fec_main.c
> @@ -3192,7 +3192,7 @@ static int fec_reset_phy(struct platform_device *pdev)
> {
> int err, phy_reset;
> bool active_high = false;
> - int msec = 1;
> + int msec = 1, phy_post_delay = 0;
> struct device_node *np = pdev->dev.of_node;
>
> if (!np)
> @@ -3210,7 +3210,6 @@ static int fec_reset_phy(struct platform_device *pdev)
> return 0;
>
> active_high = of_property_read_bool(np, "phy-reset-active-high");
> -
> err = devm_gpio_request_one(&pdev->dev, phy_reset,
> active_high ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW,
> "phy-reset");
No white space changes please.
Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
