[RFC PATCH 01/11] dt-bindings: update the binding for Allwinner H3 TVE support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Allwinner H3 features a "DE2.0" and a TV Encoder.

Add device tree bindings for the following parts:
- H3 TCONs
- H3 Mixers
- The connection between H3 TCONs and H3 Mixers
- H3 TV Encoder
- H3 Display engine

Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
---
 .../bindings/display/sunxi/sun4i-drm.txt           | 47 ++++++++++++++++++++--
 1 file changed, 43 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
index 66b85a195ef2..52781943713b 100644
--- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
+++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
@@ -21,7 +21,9 @@ The TV Encoder supports the composite and VGA output. It is one end of
 the pipeline.
 
 Required properties:
- - compatible: value should be "allwinner,sun4i-a10-tv-encoder".
+ - compatible: value must be either:
+    * allwinner,sun4i-a10-tv-encoder
+    * allwinner,sun8i-h3-tv-encoder
  - reg: base address and size of memory-mapped region
  - clocks: the clocks driving the TV encoder
  - resets: phandle to the reset controller driving the encoder
@@ -30,6 +32,13 @@ Required properties:
   Documentation/devicetree/bindings/media/video-interfaces.txt. The
   first port should be the input endpoint.
 
+For "allwinner,sun4i-a10-tv-encoder", there is only one clock required,
+and it's not named.
+
+For "allwinner,sun8i-h3-tv-encoder", these clocks are needed:
+    - 'bus': the AHB bus clock of TVE
+    - 'mod': the mod clock of TVE
+
 TCON
 ----
 
@@ -41,29 +50,51 @@ Required properties:
    * allwinner,sun6i-a31-tcon
    * allwinner,sun6i-a31s-tcon
    * allwinner,sun8i-a33-tcon
+   * allwinner,sun8i-h3-tcon0
+   * allwinner,sun8i-h3-tcon1
    * allwinner,sun8i-v3s-tcon
  - reg: base address and size of memory-mapped region
  - interrupts: interrupt associated to this IP
  - clocks: phandles to the clocks feeding the TCON. Three are needed:
    - 'ahb': the interface clocks
-   - 'tcon-ch0': The clock driving the TCON channel 0
  - resets: phandles to the reset controllers driving the encoder
    - "lcd": the reset line for the TCON channel 0
 
  - clock-names: the clock names mentioned above
  - reset-names: the reset names mentioned above
- - clock-output-names: Name of the pixel clock created
 
 - ports: A ports node with endpoint definitions as defined in
   Documentation/devicetree/bindings/media/video-interfaces.txt. The
   first port should be the input endpoint, the second one the output
 
+  In the situation of Display Engine 2.0 that the connection between
+  the mixer and the TCON can be swapped, the input should have two
+  endpoints. The first is the default mixer connected to the TCON,
+  the second the mixer which will be connected to the TCON if the
+  swap bit is set.
+
   The output should have two endpoints. The first is the block
   connected to the TCON channel 0 (usually a panel or a bridge), the
   second the block connected to the TCON channel 1 (usually the TV
   encoder)
 
-On SoCs other than the A33 and V3s, there is one more clock required:
+For the following compatibles:
+   * allwinner,sun5i-a13-tcon
+   * allwinner,sun6i-a31-tcon
+   * allwinner,sun6i-a31s-tcon
+   * allwinner,sun8i-a33-tcon
+   * allwinner,sun8i-v3s-tcon
+there is one more clock and one more property required:
+ - clocks:
+   - 'tcon-ch0': The clock driving the TCON channel 0
+ - clock-output-names: Name of the pixel clock created
+
+For the following compatibles:
+   * allwinner,sun5i-a13-tcon
+   * allwinner,sun6i-a31-tcon
+   * allwinner,sun6i-a31s-tcon
+   * allwinner,sun8i-h3-tcon0
+there is one more clock required:
    - 'tcon-ch1': The clock driving the TCON channel 1
 
 DRC
@@ -158,6 +189,8 @@ supported.
 Required properties:
   - compatible: value must be one of:
     * allwinner,sun8i-v3s-de2-mixer
+    * allwinner,sun8i-h3-de2-mixer0
+    * allwinner,sun8i-h3-de2-mixer1
   - reg: base address and size of the memory-mapped region.
   - clocks: phandles to the clocks feeding the mixer
     * bus: the mixer interface clock
@@ -169,6 +202,11 @@ Required properties:
   Documentation/devicetree/bindings/media/video-interfaces.txt. The
   first port should be the input endpoints, the second one the output
 
+  In the situation of Display Engine 2.0 that the connection between
+  the mixer and the TCON can be swapped, the output should have two
+  endpoints. The first is the default TCON connected to the mixer,
+  the second the TCON which will be connected to the mixer if the
+  swap bit is set.
 
 Display Engine Pipeline
 -----------------------
@@ -183,6 +221,7 @@ Required properties:
     * allwinner,sun6i-a31-display-engine
     * allwinner,sun6i-a31s-display-engine
     * allwinner,sun8i-a33-display-engine
+    * allwinner,sun8i-h3-display-engine
     * allwinner,sun8i-v3s-display-engine
 
   - allwinner,pipelines: list of phandle to the display engine
-- 
2.12.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux