Hi, On Tue, May 16, 2017 at 4:30 AM, Anup Patel <anup.patel@xxxxxxxxxxxx> wrote: > This patchset adds initial support of Broadcom Stingray SOC > by reusing existing Broadcom iProc device drivers. > > Most of the patches in this patchset are DT patches except > the Stingray clock tree support which just one patch. > > This patchset is based on Linux-4.12-rc1 and it is also available > at stingray-v3 branch of https://github.com/Broadcom/arm64-linux.git > > Changes since v2: > - Remove default bootargs from chosen DT node > - Remove "linux" prefix from stdout DT attribute of chosen DT node > - Remove use of GIC_CPU_MASK_xxx() for PPIs > > Changes since v1: > - Rebased patches for Linux-4.12-rc1 > - Removed unwanted /memreserve/ from bcm958742-base.dtsi > - Use ranges DT property to clear view of memory-layout > - Make bcm-sr.h part of clock DT bindings patch > > Anup Patel (3): > dt-bindings: bcm: Add Broadcom Stingray bindings document > arm64: dts: Initial DTS files for Broadcom Stingray SOC > arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray > > Oza Pawandeep (1): > arm64: dts: Add I2C DT nodes for Stingray SoC > > Pramod Kumar (3): > arm64: dts: Add NAND DT nodes for Stingray SOC > arm64: dts: Add pinctrl DT nodes for Stingray SOC > arm64: dts: Add GPIO DT nodes for Stingray SOC > > Sandeep Tripathy (3): > dt-bindings: clk: Extend binding doc for Stingray SOC > clk: bcm: Add clocks for Stingray SOC > arm64: dts: Add clock DT nodes for Stingray SOC > > Srinath Mannam (1): > arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC > > .../devicetree/bindings/arm/bcm/brcm,stingray.txt | 12 + > .../bindings/clock/brcm,iproc-clocks.txt | 76 ++++ > arch/arm64/boot/dts/broadcom/Makefile | 1 + > arch/arm64/boot/dts/broadcom/stingray/Makefile | 6 + > .../boot/dts/broadcom/stingray/bcm958742-base.dtsi | 131 ++++++ > .../boot/dts/broadcom/stingray/bcm958742k.dts | 78 ++++ > .../boot/dts/broadcom/stingray/bcm958742t.dts | 40 ++ > .../boot/dts/broadcom/stingray/stingray-clock.dtsi | 170 ++++++++ > .../dts/broadcom/stingray/stingray-pinctrl.dtsi | 345 ++++++++++++++++ > .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 460 +++++++++++++++++++++ > drivers/clk/bcm/Kconfig | 8 + > drivers/clk/bcm/Makefile | 1 + > drivers/clk/bcm/clk-sr.c | 300 ++++++++++++++ > include/dt-bindings/clock/bcm-sr.h | 101 +++++ > .../dt-bindings/pinctrl/brcm,pinctrl-stingray.h | 68 +++ > 15 files changed, 1797 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/bcm/brcm,stingray.txt > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/Makefile > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-clock.dtsi > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-pinctrl.dtsi > create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi > create mode 100644 drivers/clk/bcm/clk-sr.c > create mode 100644 include/dt-bindings/clock/bcm-sr.h > create mode 100644 include/dt-bindings/pinctrl/brcm,pinctrl-stingray.h Grouping as one patchset for review is fine, but when you submit this for merge you need to split it up: - Documentation/devicetree can go with the driver pieces or with the DT changes, your choice - DTS/DTSI changes should go through the Broadcom maintainers to arm-soc - clk changes should go to clk maintainers. Also, there's usually no need to split up a DT introduction and having separate pieces for NAND/pinctrl/GPIO/etc: They can all go in the main DT submission patch. -Olof -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
