Re: [PATCH 1/4] ata: Add DT bindings for Faraday Technology FTIDE010

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Monday, May 08, 2017 10:26:49 PM Linus Walleij wrote:
> On Mon, May 8, 2017 at 12:47 PM, Bartlomiej Zolnierkiewicz
> <b.zolnierkie@xxxxxxxxxxx> wrote:
> 
> > Also for all current drivers we just put timing values (or a logic
> > to calculate them from the standard ATA timings) into the driver
> > itself and not device tree (as they are based on values are dictated
> > by ATA standard and should not change for a given controller type).
> 
> I had it like that at first (and I can of course switch it back). But I
> came to think this is better.
> 
> I was looking at these values from the point that it depends a bit
> on the silicon where it is synthesized. So the vendor tree has
> things like this:
> 
> #ifndef SL2312_FPGA_IDE
> static unsigned char PIO_TIMING[5] = { 0xaa, 0xa3, 0xa1, 0x33, 0x31 };
> static unsigned char TIMING_MDMA_50M[3] = { 0x66, 0x22, 0x21 };
> static unsigned char TIMING_MDMA_66M[3] = { 0x88, 0x32, 0x31 };
> static unsigned char TIMING_UDMA_50M[6] = { 0x33, 0x31, 0x21, 0x21,
> 0x11, 0x91 };
> static unsigned char TIMING_UDMA_66M[7] = { 0x44, 0x42, 0x31, 0x21,
> 0x11, 0x91,  0x91};
> #else
> static unsigned char PIO_TIMING[5] = { 0x88, 0x82, 0x81, 0x32, 0x21 };
> static unsigned char TIMING_MDMA_50M[3] = { 0x33, 0x11, 0x11 };
> static unsigned char TIMING_MDMA_66M[3] = { 0x33, 0x11, 0x11 };
> static unsigned char TIMING_UDMA_50M[6] = { 0x22, 0x11, 0x11, 0x11 };
> static unsigned char TIMING_UDMA_66M[7] = { 0x22, 0x11, 0x11, 0x11 };
> #endif
> 
> (From D-Link DIR-685 source release from Storlink/Cortina board support.)
> 
> So depending on whether they use an FPGA or an ASIC the values are
> different, no matter what frequency (50 or 66 MHz) is used. So it is not
> derived from frequency.
> 
> So I think it makes most sense to have it in the device tree as we don't
> know what designs are out there.

I still would prefer to keep timing values private to the driver and just
select the controller type (FPGA/ASIC) using the device tree.

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux