On Saturday, May 06, 2017 02:10:51 PM Linus Walleij wrote: > This adds device tree bindings for the Cortina Systems Gemini > PATA to SATA bridge. > > Cc: devicetree@xxxxxxxxxxxxxxx > Cc: John Feng-Hsin Chiang <john453@xxxxxxxxxxxxxxxx> > Cc: Greentime Hu <green.hu@xxxxxxxxx> > Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx> > --- > .../bindings/ata/cortina,gemini-sata-bridge.txt | 55 ++++++++++++++++++++++ > 1 file changed, 55 insertions(+) > create mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt > > diff --git a/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt > new file mode 100644 > index 000000000000..9fe92818b2fb > --- /dev/null > +++ b/Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt > @@ -0,0 +1,55 @@ > +* Cortina Systems Gemini SATA Bridge > + > +The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that > +takes two Faraday Technology FTIDE010 PATA controllers and bridges > +them in different configurations to two SATA ports. > + > +Required properties: > +- compatible: should be > + "cortina,gemini-sata-bridge" > +- reg: registers and size for the block > +- resets: phandles to the reset lines for both SATA bridges > +- reset-names: must be "sata0", "sata1" > +- clocks: phandles to the compulsory peripheral clocks > +- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" > +- syscon: a phandle to the global Gemini system controller > +- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for > + the ATA controller and SATA bridges. Values 0..3: > + Mode 0: ata0 master <-> sata0 > + ata1 master <-> sata1 > + ata0 slave interface brought out on IDE pads > + Mode 1: ata0 master <-> sata0 > + ata1 master <-> sata1 > + ata1 slave interface brought out on IDE pads > + Mode 2: ata1 master <-> sata1 > + ata1 slave <-> sata0 > + ata0 master and slave interfaces brought out > + on IDE pads > + Mode 3: ata0 master <-> sata0 > + ata1 slave <-> sata1 ata0 slave? > + ata1 master and slave interfaces brought out > + on IDE pads > + > +Optional boolean properties: > +- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. > + The muxmode setting decides whether ATA0 or ATA1 is brought out, > + and whether master, slave or both interfaces get brought out. > +- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge > + inside the Gemnini SoC. The Muxmode decides what PATA blocks will > + be muxed out and how. > + > +Example: > + > +sata: sata@46000000 { > + compatible = "cortina,gemini-sata-bridge"; > + reg = <0x46000000 0x100>; > + resets = <&rcon 26>, <&rcon 27>; > + reset-names = "sata0", "sata1"; > + clocks = <&gcc GEMINI_CLK_GATE_SATA0>, > + <&gcc GEMINI_CLK_GATE_SATA1>; > + clock-names = "SATA0_PCLK", "SATA1_PCLK"; > + syscon = <&syscon>; > + cortina,gemini-ata-muxmode = <3>; > + cortina,gemini-enable-ide-pins; > + cortina,gemini-enable-sata-bridge; > +}; Best regards, -- Bartlomiej Zolnierkiewicz Samsung R&D Institute Poland Samsung Electronics -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html