Re: [PATCH v2 2/2] [media] platform: add video-multiplexer subdevice driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Philipp,

Thanks for continuing working on this!

I have some minor comments below...

On Tue, May 02, 2017 at 05:09:13PM +0200, Philipp Zabel wrote:
> This driver can handle SoC internal and external video bus multiplexers,
> controlled by mux controllers provided by the mux controller framework,
> such as MMIO register bitfields or GPIOs. The subdevice passes through
> the mbus configuration of the active input to the output side.
> 
> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
> Signed-off-by: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
> ---
> Changes since v1 [1]:
>  - Protect vmux->active with a mutex in link_setup and set_format.
>    s_stream does not need to be locked; it is called when the pipeline
>    is started and thus the link setup can not be changed anymore.
>  - Remove the unused g_mbus_config.
> 
> This was previously sent as part of Steve's i.MX media series [2].
> 
> [1] https://patchwork.kernel.org/patch/9704791/
> [2] https://patchwork.kernel.org/patch/9647869/
> ---
>  drivers/media/platform/Kconfig     |   6 +
>  drivers/media/platform/Makefile    |   2 +
>  drivers/media/platform/video-mux.c | 312 +++++++++++++++++++++++++++++++++++++
>  3 files changed, 320 insertions(+)
>  create mode 100644 drivers/media/platform/video-mux.c
> 
> diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
> index c9106e105baba..b046a6d39fee5 100644
> --- a/drivers/media/platform/Kconfig
> +++ b/drivers/media/platform/Kconfig
> @@ -74,6 +74,12 @@ config VIDEO_M32R_AR_M64278
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called arv.
>  
> +config VIDEO_MUX
> +	tristate "Video Multiplexer"
> +	depends on OF && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER && MULTIPLEXER
> +	help
> +	  This driver provides support for N:1 video bus multiplexers.
> +
>  config VIDEO_OMAP3
>  	tristate "OMAP 3 Camera support"
>  	depends on VIDEO_V4L2 && I2C && VIDEO_V4L2_SUBDEV_API && ARCH_OMAP3
> diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile
> index 349ddf6a69da2..fd2735ca3ff75 100644
> --- a/drivers/media/platform/Makefile
> +++ b/drivers/media/platform/Makefile
> @@ -27,6 +27,8 @@ obj-$(CONFIG_VIDEO_SH_VEU)		+= sh_veu.o
>  
>  obj-$(CONFIG_VIDEO_MEM2MEM_DEINTERLACE)	+= m2m-deinterlace.o
>  
> +obj-$(CONFIG_VIDEO_MUX)			+= video-mux.o
> +
>  obj-$(CONFIG_VIDEO_S3C_CAMIF) 		+= s3c-camif/
>  obj-$(CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS) 	+= exynos4-is/
>  obj-$(CONFIG_VIDEO_SAMSUNG_S5P_JPEG)	+= s5p-jpeg/
> diff --git a/drivers/media/platform/video-mux.c b/drivers/media/platform/video-mux.c
> new file mode 100644
> index 0000000000000..a857f5e89deff
> --- /dev/null
> +++ b/drivers/media/platform/video-mux.c
> @@ -0,0 +1,312 @@
> +/*
> + * video stream multiplexer controlled via mux control
> + *
> + * Copyright (C) 2013 Pengutronix, Sascha Hauer <kernel@xxxxxxxxxxxxxx>
> + * Copyright (C) 2016-2017 Pengutronix, Philipp Zabel <kernel@xxxxxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/err.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/mux/consumer.h>
> +#include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/platform_device.h>
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-subdev.h>
> +#include <media/v4l2-of.h>

Could you rebase this on the V4L2 fwnode patchset here, please?

<URL:https://git.linuxtv.org/sailus/media_tree.git/log/?h=v4l2-acpi>

The conversion is rather simple, as shown here:

<URL:https://git.linuxtv.org/sailus/media_tree.git/commit/?h=v4l2-acpi&id=679035e11bfdbea146fed5d52fb794b34dc9cea6>

> +
> +struct video_mux {
> +	struct v4l2_subdev subdev;
> +	struct media_pad *pads;
> +	struct v4l2_mbus_framefmt *format_mbus;
> +	struct v4l2_of_endpoint *endpoint;
> +	struct mux_control *mux;
> +	struct mutex lock;
> +	int active;
> +};
> +
> +static inline struct video_mux *v4l2_subdev_to_video_mux(struct v4l2_subdev *sd)
> +{
> +	return container_of(sd, struct video_mux, subdev);
> +}
> +
> +static inline bool is_source_pad(struct video_mux *vmux, unsigned int pad)

It's a common practice to test pad flags rather than the pad number.
Although the pad number here implicitly tells this, too, testing pad flags
is cleaner.

The matter was discussed in the past and it was decided not to add helper
functions to the framework for the purpose as testing the flags is trivial.

> +{
> +	return pad == vmux->subdev.entity.num_pads - 1;
> +}
> +
> +static int video_mux_link_setup(struct media_entity *entity,
> +				const struct media_pad *local,
> +				const struct media_pad *remote, u32 flags)
> +{
> +	struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
> +	struct video_mux *vmux = v4l2_subdev_to_video_mux(sd);
> +	int ret = 0;
> +
> +	/*
> +	 * The mux state is determined by the enabled sink pad link.
> +	 * Enabling or disabling the source pad link has no effect.
> +	 */
> +	if (is_source_pad(vmux, local->index))
> +		return 0;
> +
> +	dev_dbg(sd->dev, "link setup '%s':%d->'%s':%d[%d]",
> +		remote->entity->name, remote->index, local->entity->name,
> +		local->index, flags & MEDIA_LNK_FL_ENABLED);
> +
> +	mutex_lock(&vmux->lock);
> +
> +	if (flags & MEDIA_LNK_FL_ENABLED) {
> +		if (vmux->active == local->index)
> +			goto out;
> +
> +		if (vmux->active >= 0) {
> +			ret = -EBUSY;
> +			goto out;
> +		}
> +
> +		dev_dbg(sd->dev, "setting %d active\n", local->index);
> +		ret = mux_control_try_select(vmux->mux, local->index);
> +		if (ret < 0)
> +			goto out;
> +		vmux->active = local->index;
> +	} else {
> +		if (vmux->active != local->index)
> +			goto out;
> +
> +		dev_dbg(sd->dev, "going inactive\n");
> +		mux_control_deselect(vmux->mux);
> +		vmux->active = -1;
> +	}
> +
> +out:
> +	mutex_unlock(&vmux->lock);
> +	return ret;
> +}
> +
> +static struct media_entity_operations video_mux_ops = {
> +	.link_setup = video_mux_link_setup,
> +	.link_validate = v4l2_subdev_link_validate,
> +};
> +
> +static bool video_mux_endpoint_disabled(struct device_node *ep)
> +{
> +	struct device_node *rpp = of_graph_get_remote_port_parent(ep);
> +
> +	return !of_device_is_available(rpp);
> +}
> +
> +static int video_mux_s_stream(struct v4l2_subdev *sd, int enable)
> +{
> +	struct video_mux *vmux = v4l2_subdev_to_video_mux(sd);
> +	struct v4l2_subdev *upstream_sd;
> +	struct media_pad *pad;
> +
> +	if (vmux->active == -1) {
> +		dev_err(sd->dev, "Can not start streaming on inactive mux\n");
> +		return -EINVAL;
> +	}
> +
> +	pad = media_entity_remote_pad(&sd->entity.pads[vmux->active]);
> +	if (!pad) {
> +		dev_err(sd->dev, "Failed to find remote source pad\n");
> +		return -ENOLINK;
> +	}
> +
> +	if (!is_media_entity_v4l2_subdev(pad->entity)) {
> +		dev_err(sd->dev, "Upstream entity is not a v4l2 subdev\n");
> +		return -ENODEV;
> +	}
> +
> +	upstream_sd = media_entity_to_v4l2_subdev(pad->entity);
> +
> +	return v4l2_subdev_call(upstream_sd, video, s_stream, enable);
> +}
> +
> +static const struct v4l2_subdev_video_ops video_mux_subdev_video_ops = {
> +	.s_stream = video_mux_s_stream,
> +};
> +
> +static struct v4l2_mbus_framefmt *
> +__video_mux_get_pad_format(struct v4l2_subdev *sd,
> +			   struct v4l2_subdev_pad_config *cfg,
> +			   unsigned int pad, u32 which)
> +{
> +	struct video_mux *vmux = v4l2_subdev_to_video_mux(sd);
> +
> +	switch (which) {
> +	case V4L2_SUBDEV_FORMAT_TRY:
> +		return v4l2_subdev_get_try_format(sd, cfg, pad);
> +	case V4L2_SUBDEV_FORMAT_ACTIVE:
> +		return &vmux->format_mbus[pad];
> +	default:
> +		return NULL;
> +	}
> +}
> +
> +static int video_mux_get_format(struct v4l2_subdev *sd,
> +			    struct v4l2_subdev_pad_config *cfg,
> +			    struct v4l2_subdev_format *sdformat)
> +{
> +	sdformat->format = *__video_mux_get_pad_format(sd, cfg, sdformat->pad,
> +						   sdformat->which);
> +	return 0;
> +}
> +
> +static int video_mux_set_format(struct v4l2_subdev *sd,
> +			    struct v4l2_subdev_pad_config *cfg,
> +			    struct v4l2_subdev_format *sdformat)
> +{
> +	struct video_mux *vmux = v4l2_subdev_to_video_mux(sd);
> +	struct v4l2_mbus_framefmt *mbusformat;
> +
> +	mbusformat = __video_mux_get_pad_format(sd, cfg, sdformat->pad,
> +					    sdformat->which);
> +	if (!mbusformat)
> +		return -EINVAL;
> +
> +	mutex_lock(&vmux->lock);
> +
> +	/* Source pad mirrors active sink pad, no limitations on sink pads */
> +	if (is_source_pad(vmux, sdformat->pad) && vmux->active >= 0)
> +		sdformat->format = vmux->format_mbus[vmux->active];
> +
> +	mutex_unlock(&vmux->lock);
> +
> +	*mbusformat = sdformat->format;

Shouldn't you do this before releasing the mutex? The assignment won't be
an atomic operation. Same for get_format; you should take the mutex.

> +
> +	return 0;
> +}
> +
> +static struct v4l2_subdev_pad_ops video_mux_pad_ops = {
> +	.get_fmt = video_mux_get_format,
> +	.set_fmt = video_mux_set_format,
> +};
> +
> +static struct v4l2_subdev_ops video_mux_subdev_ops = {

Const for both of the structs?

> +	.pad = &video_mux_pad_ops,
> +	.video = &video_mux_subdev_video_ops,
> +};
> +
> +static int video_mux_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device *dev = &pdev->dev;
> +	struct v4l2_of_endpoint endpoint;
> +	struct device_node *ep;
> +	struct video_mux *vmux;
> +	unsigned int num_pads = 0;
> +	int ret;
> +	int i;
> +
> +	vmux = devm_kzalloc(dev, sizeof(*vmux), GFP_KERNEL);
> +	if (!vmux)
> +		return -ENOMEM;
> +
> +	platform_set_drvdata(pdev, vmux);
> +
> +	v4l2_subdev_init(&vmux->subdev, &video_mux_subdev_ops);
> +	snprintf(vmux->subdev.name, sizeof(vmux->subdev.name), "%s", np->name);
> +	vmux->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> +	vmux->subdev.dev = dev;
> +
> +	/*
> +	 * The largest numbered port is the output port. It determines
> +	 * total number of pads.
> +	 */
> +	for_each_endpoint_of_node(np, ep) {
> +		of_graph_parse_endpoint(ep, &endpoint.base);
> +		num_pads = max(num_pads, endpoint.base.port + 1);
> +	}
> +
> +	if (num_pads < 2) {
> +		dev_err(dev, "Not enough ports %d\n", num_pads);
> +		return -EINVAL;
> +	}
> +
> +	vmux->mux = devm_mux_control_get(dev, NULL);
> +	if (IS_ERR(vmux->mux)) {
> +		ret = PTR_ERR(vmux->mux);
> +		if (ret != -EPROBE_DEFER)
> +			dev_err(dev, "Failed to get mux: %d\n", ret);
> +		return ret;
> +	}
> +
> +	mutex_init(&vmux->lock);
> +	vmux->active = -1;
> +	vmux->pads = devm_kzalloc(dev, sizeof(*vmux->pads) * num_pads,
> +				  GFP_KERNEL);
> +	vmux->format_mbus = devm_kzalloc(dev, sizeof(*vmux->format_mbus) *
> +					 num_pads, GFP_KERNEL);
> +	vmux->endpoint = devm_kzalloc(dev, sizeof(*vmux->endpoint) *
> +				      (num_pads - 1), GFP_KERNEL);
> +
> +	for (i = 0; i < num_pads - 1; i++)
> +		vmux->pads[i].flags = MEDIA_PAD_FL_SINK;
> +	vmux->pads[num_pads - 1].flags = MEDIA_PAD_FL_SOURCE;
> +
> +	vmux->subdev.entity.function = MEDIA_ENT_F_VID_MUX;
> +	ret = media_entity_pads_init(&vmux->subdev.entity, num_pads,
> +				     vmux->pads);
> +	if (ret < 0)
> +		return ret;
> +
> +	vmux->subdev.entity.ops = &video_mux_ops;
> +
> +	for_each_endpoint_of_node(np, ep) {
> +		v4l2_of_parse_endpoint(ep, &endpoint);
> +
> +		if (video_mux_endpoint_disabled(ep)) {
> +			dev_dbg(dev, "port %d disabled\n", endpoint.base.port);
> +			continue;
> +		}
> +
> +		vmux->endpoint[endpoint.base.port] = endpoint;
> +	}
> +
> +	return v4l2_async_register_subdev(&vmux->subdev);
> +}
> +
> +static int video_mux_remove(struct platform_device *pdev)
> +{
> +	struct video_mux *vmux = platform_get_drvdata(pdev);
> +	struct v4l2_subdev *sd = &vmux->subdev;
> +
> +	v4l2_async_unregister_subdev(sd);
> +	media_entity_cleanup(&sd->entity);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id video_mux_dt_ids[] = {
> +	{ .compatible = "video-mux", },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, video_mux_dt_ids);
> +
> +static struct platform_driver video_mux_driver = {
> +	.probe		= video_mux_probe,
> +	.remove		= video_mux_remove,
> +	.driver		= {
> +		.of_match_table = video_mux_dt_ids,
> +		.name = "video-mux",
> +	},
> +};
> +
> +module_platform_driver(video_mux_driver);
> +
> +MODULE_DESCRIPTION("video stream multiplexer");
> +MODULE_AUTHOR("Sascha Hauer, Pengutronix");
> +MODULE_AUTHOR("Philipp Zabel, Pengutronix");
> +MODULE_LICENSE("GPL");

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@xxxxxx	XMPP: sailus@xxxxxxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux