On Fri, 2017-04-28 at 13:32 -0500, Rob Herring wrote: > On Tue, Apr 25, 2017 at 10:06:44AM +0800, hean.loong.ong@xxxxxxxxx > wrote: > > > > From: "Ong, Hean Loong" <hean.loong.ong@xxxxxxxxx> > > > > Device tree binding for Intel FPGA Video and Image > > Processing Suite. The binding involved would be generated > > from the Altera (Intel) Qsys system. The bindings would > > set the max width, max height, buts per pixel and memory > > port width. The device tree binding only supports the Intel > > Arria10 devkit and its variants. Vendor name retained as > > altr. > > > > Signed-off-by: Ong, Hean Loong <hean.loong.ong@xxxxxxxxx> > > --- > > v2: > > * Moved Device Tree bindings to > > Documentation/devicetree/bindings/display/ > > * Added vendor name altr, to description > > --- > > .../devicetree/bindings/display/altr,vip-fb2.txt | 30 > > ++++++++++++++++++++++ > > 1 file changed, 30 insertions(+) > > create mode 100644 > > Documentation/devicetree/bindings/display/altr,vip-fb2.txt > > > > diff --git a/Documentation/devicetree/bindings/display/altr,vip- > > fb2.txt b/Documentation/devicetree/bindings/display/altr,vip- > > fb2.txt > > new file mode 100644 > > index 0000000..bdffefb > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/display/altr,vip-fb2.txt > > @@ -0,0 +1,30 @@ > > +Intel Video and Image Processing(VIP) Frame Buffer II bindings > > + > > +Supported hardware: Arria 10 and above with display port IP > > + > > +The drm driver for the Arria 10 devkit would require the display > > resolution > Bindings describe h/w. DRM driver is a Linux term. > Noted. > > > > +and pixel information to be included as these values are generated > > based > > +on the FPGA design that drives the video connector attached to the > > drm driver > > +Information the FPGA video IP component can be acquired from > > +https://www.altera.com/content/dam/altera-www/global/en_US/pdfs/li > > terature/ug/ug_vip.pdf > > + > > +Required properties: > > + > > +- compatible: "altr,vip-frame-buffer-2.0" > > +- reg: Physical base address and length of the framebuffer > > controller's > > + registers. > > +- altr,max-width: The width of the framebuffer in pixels. > > +- altr,max-height: The height of the framebuffer in pixels. > > +- altr,bits-per-symbol: only "8" is currently supported > Supported in the driver or IP? The former isn't relevant to the > binding. > In the latter case, you don't need it if that's the only thing > supported. > Since the device is an FPGA the values here are based on how the FPGA HW design is created or programmed. The values here are the optimal reference design proposed for the Intel Arria10 devkit. However anyone that uses the Intel Arria10 devkit could create a device that runs with a different resolution that has varying values but with the condition that they need to fill these values accordingly with Intel Quartus Programmer tools. Once programmed the parameters could not be changed at runtime and the HW rerence designs currently only support 1 type of resolution per design. Therefore the driver needs to support a hardware with varying parameters programmed specifically into the FPGA. > > > > +- altr,mem-port-width = the bus width of the avalon master port on > > the frame reader > In bits or bytes? > > > > > + > > +Example: > > + > > + dp_0_frame_buf: vip@100000280 { > > + compatible = "altr,vip-frame-buffer-2.0"; > > + reg = <0x00000001 0x00000280 0x00000040>; > > + altr,max-width = <1280>; > > + altr,max-height = <720>; > > + altr,bits-per-symbol = <8>; > > + altr,mem-port-width = <128>; > > + };��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f