Added initial binding documentation for S2MPA01 MFD. Signed-off-by: Sachin Kamat <sachin.kamat@xxxxxxxxxx> --- Documentation/devicetree/bindings/mfd/s2mpa01.txt | 91 +++++++++++++++++++++ 1 file changed, 91 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/s2mpa01.txt diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt new file mode 100644 index 000000000000..ae750a28821b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/s2mpa01.txt @@ -0,0 +1,91 @@ + +* Samsung S2MPA01 Voltage and Current Regulator + +The Samsung S2MPA01 is a multi-function device which includes high +efficiency buck converters including Dual-Phase buck converter, various LDOs, +and an RTC. It is interfaced to the host controller using an I2C interface. +Each sub-block is addressed by the host system using different I2C slave +addresses. + +Required properties: +- compatible: Should be "samsung,s2mpa01-pmic". +- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mpa01 are delivered to. +- interrupts: Interrupt specifiers for interrupt sources. + +Optional nodes: +- regulators: The regulators of s2mpa01 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + [standard regulator constraints....]; + }; + + regulator-ramp-delay for BUCKs = [6250/12500(default)/25000/50000] uV/us + + BUCK[1/2/3/4] supports disabling ramp delay on hardware, so explictly + regulator-ramp-delay = <0> can be used for them to disable ramp delay. + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + +NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set +for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. +Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], +BUCK[2, 4], and BUCK[8, 9, 10] + +The regulator constraints inside the regulator nodes use the standard regulator +bindings which are documented elsewhere. + +The following are the names of the regulators that the s2mpa01 PMIC block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s2mpa01. + + - LDOn + - valid values for n are 1 to 26 + - Example: LDO1, LD02, LDO26 + - BUCKn + - valid values for n are 1 to 10. + - Example: BUCK1, BUCK2, BUCK9 + +Example: + + s2mpa01_pmic@66 { + compatible = "samsung,s2mpa01-pmic"; + reg = <0x66>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html