Hello,
On Thursday 16 Feb 2017 11:02:55 Ramesh Shanmugasundaram wrote:
> Hi Rob,
>
> Thank you for the review comments.
>
> > Subject: Re: [PATCH v3 6/7] dt-bindings: media: Add Renesas R-Car DRIF
> > binding
> >
> > On Tue, Feb 07, 2017 at 03:02:36PM +0000, Ramesh Shanmugasundaram wrote:
> >> Add binding documentation for Renesas R-Car Digital Radio Interface
> >> (DRIF) controller.
> >>
> >> Signed-off-by: Ramesh Shanmugasundaram
> >> <ramesh.shanmugasundaram@xxxxxxxxxxxxxx>
> >> ---
> >>
> >> .../devicetree/bindings/media/renesas,drif.txt | 186 ++++++++++++++
> >> 1 file changed, 186 insertions(+)
> >> create mode 100644
> >>
> >> Documentation/devicetree/bindings/media/renesas,drif.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt
> >> b/Documentation/devicetree/bindings/media/renesas,drif.txt
> >> new file mode 100644
> >> index 0000000..6315609
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/media/renesas,drif.txt
> >> @@ -0,0 +1,186 @@
> >> +Renesas R-Car Gen3 Digital Radio Interface controller (DRIF)
> >> +------------------------------------------------------------
> >> +
> >> +R-Car Gen3 DRIF is a SPI like receive only slave device. A general
> >> +representation of DRIF interfacing with a master device is shown below.
> >> +
> >> ++---------------------+ +---------------------+
> >> +| |-----SCK------->|CLK |
> >> +| Master |-----SS-------->|SYNC DRIFn (slave) |
> >> +| |-----SD0------->|D0 |
> >> +| |-----SD1------->|D1 |
> >> ++---------------------+ +---------------------+
> >> +
> >> +As per the datasheet, each DRIF channel (drifn) is made up of two
> >> +internal channels (drifn0 & drifn1). These two internal channels
> >> +share the common CLK & SYNC. Each internal channel has its own
> >> +dedicated resources like irq, dma channels, address space & clock.
> >> +This internal split is not visible to the external master device.
> >> +
> >> +The device tree model represents each internal channel as a separate
> >> node.
> >> +The internal channels sharing the CLK & SYNC are tied together by
> >> +their phandles using a new property called "renesas,bonding". For the
> >> +rest of the documentation, unless explicitly stated, the word channel
> >> +implies an internal channel.
> >> +
> >> +When both internal channels are enabled they need to be managed
> >> +together as one (i.e.) they cannot operate alone as independent
> >> +devices. Out of the two, one of them needs to act as a primary device
> >> +that accepts common properties of both the internal channels. This
> >> +channel is identified by a new property called "renesas,primary-bond".
> >> +
> >> +To summarize,
> >> + - When both the internal channels that are bonded together are
> >> enabled,
> >> + the zeroth channel is selected as primary-bond. This channels
> >> accepts
> >> + properties common to all the members of the bond.
> >> + - When only one of the bonded channels need to be enabled, the
> >> property
> >> + "renesas,bonding" or "renesas,primary-bond" will have no effect.
> >> That
> >> + enabled channel can act alone as any other independent device.
> >> +
> >> +Required properties of an internal channel:
> >> +-------------------------------------------
> >> +- compatible: "renesas,r8a7795-drif" if DRIF controller is a part of
> >> R8A7795 SoC.
> >> + "renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible
> >> device.
> >> + When compatible with the generic version, nodes must list the
> >> + SoC-specific version corresponding to the platform first
> >> + followed by the generic version.
> >> +- reg: offset and length of that channel.
> >> +- interrupts: associated with that channel.
> >> +- clocks: phandle and clock specifier of that channel.
> >> +- clock-names: clock input name string: "fck".
> >> +- dmas: phandles to the DMA channels.
> >> +- dma-names: names of the DMA channel: "rx".
> >> +- renesas,bonding: phandle to the other channel.
> >> +
> >> +Optional properties of an internal channel:
> >> +-------------------------------------------
> >> +- power-domains: phandle to the respective power domain.
> >> +
> >> +Required properties of an internal channel when:
> >> + - It is the only enabled channel of the bond (or)
> >> + - If it acts as primary among enabled bonds
> >> +--------------------------------------------------------
> >> +- pinctrl-0: pin control group to be used for this channel.
> >> +- pinctrl-names: must be "default".
> >> +- renesas,primary-bond: empty property indicating the channel acts as
> >> primary
> >> + among the bonded channels.
> >> +- port: child port node of a channel that defines the local and remote
> >> + endpoints. The remote endpoint is assumed to be a third party tuner
> >> + device endpoint.
> >> +
> >> +Optional endpoint property:
> >> +---------------------------
> >> +- renesas,sync-active : Indicates sync signal polarity, 0/1 for
> >> low/high
> >> + respectively. This property maps to SYNCAC bit in the
> >> + hardware manual. The default is 1 (active high)
> >
> > Why does this belong in the endpoint? I'd prefer to not have vendor
> > specific properties in endpoints. Is this a property of the tuner or DRIF?
In the general case, the sync signal polarity is a property of the tuner (and
in some cases it could even be configurable on the tuner side), which could
then be queried at runtime from the tuner by the DRIF driver. However, there
could be logic on the board that would invert the polarity, so we need to
specify it on the DRIF side as well. As the polarity can differ between
different tuners, it makes sense to specify it in the endpoint, in case
multiple tuners are connected (keeping in mind that only one of them can be
used at a time). However, I we don't support connecting multiple tuners at
this time, and I don't think we ever will, but I could be wrong there.
> This property is similar to the properties in
> Documentation/devicetree/bindings/media/video-interfaces.txt (e.g.
> hsync-active, vsync-active).Hence, Laurent & Hans suggested this to be
> defined as an endpoint property and try to standardize it.
>
> I think I see your point. As endpoint properties can be defined on both
> endpoints, having a vendor specific property is a problem with a third
> party tuner. We could remove the vendor tag and make it a generic property
> "sync-active", if you are OK with it?
>
> This property can be defined for both tuner and DRIF. However, it would
> mostly be a constant in the case of tuner because as per I2S spec,
> transmitter WS (sync) changes from high->low & low->high always. Only DRIF
> allows the option to latch when WS high->low or low->high - both cases.
>
> In a traditional use case it is always WS high->low latching to get the
> first data. However, with DRIF & MAX2175 combo, our latest investigations
> reveal that latching when WS low->high provided better synchronization on
> all cases. There is no loss of data by doing this. Hence, it would be nice
> to retain this as a configurable property.
>
> Please advice.
>
> >> +
> >> +Example
> >> +--------
> >> +
> >> +SoC common dtsi file
> >> +
> >> + drif00: rif@e6f40000 {
> >> + compatible = "renesas,r8a7795-drif",
> >> + "renesas,rcar-gen3-drif";
> >> + reg = <0 0xe6f40000 0 0x64>;
> >> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> >> + clocks = <&cpg CPG_MOD 515>;
> >> + clock-names = "fck";
> >> + dmas = <&dmac1 0x20>, <&dmac2 0x20>;
> >> + dma-names = "rx", "rx";
> >> + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> >> + renesas,bonding = <&drif01>;
> >> + status = "disabled";
> >
> > Don't put "status" in examples.
>
> OK. Will note this down for future patches. Will be corrected in the next
> version.
>
> >> + };
> >> +
> >> + drif01: rif@e6f50000 {
> >> + compatible = "renesas,r8a7795-drif",
> >> + "renesas,rcar-gen3-drif";
> >> + reg = <0 0xe6f50000 0 0x64>;
> >> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> >> + clocks = <&cpg CPG_MOD 514>;
> >> + clock-names = "fck";
> >> + dmas = <&dmac1 0x22>, <&dmac2 0x22>;
> >> + dma-names = "rx", "rx";
> >> + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
> >> + renesas,bonding = <&drif00>;
> >> + status = "disabled";
> >> + };
> >> +
> >> +
> >> +Board specific dts file
> >
> > Chip vs. board in not relevant to the binding doc. Please combine them
> > here in your example.
>
> Will do.
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
