This adds documentation of device tree bindings for the STM32 DCMI
(Digital Camera Memory Interface).
Signed-off-by: Hugues Fruchet <hugues.fruchet@xxxxxx>
---
.../devicetree/bindings/media/st,stm32-dcmi.txt | 77 ++++++++++++++++++++++
1 file changed, 77 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
new file mode 100644
index 0000000..f0dc709
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
@@ -0,0 +1,77 @@
+STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
+
+Required properties:
+- compatible: "st,stm32-dcmi"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the DCMI;
+- clocks: list of clock specifiers, corresponding to entries in
+ the clock-names property;
+- clock-names: must contain "mclk", which is the DCMI peripherial clock.
+- resets: Reference to a reset controller
+- reset-names: see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
+
+DCMI supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+Device node example
+-------------------
+ dcmi: dcmi@50050000 {
+ compatible = "st,stm32-dcmi";
+ reg = <0x50050000 0x400>;
+ interrupts = <78>;
+ resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
+ clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
+ clock-names = "mclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcmi_pins>;
+ dmas = <&dma2 1 1 0x414 0x3>;
+ dma-names = "tx";
+ status = "disabled";
+ };
+
+Board setup example
+-------------------
+
+&dcmi {
+ status = "okay";
+
+ port {
+ dcmi_0: endpoint@0 {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ };
+ };
+};
+
+{
+ [...]
+ i2c@0 {
+ ov2640: camera@30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>;
+ pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>;
+ clocks = <&clk_ext_camera>;
+ clock-names = "xvclk";
+ status = "okay";
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&dcmi_0>;
+ };
+ };
+ };
+ };
+
+ clk_ext_camera: clk-ext-camera {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+}
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
