From: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> MFD support for DA9061 is provided as part of the DA9062 device driver. The registers header file adds two new chip variant IDs defined in DA9061 and DA9062 hardware. The core header file adds new software enumerations for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration for distinguishing between DA9061/62 devices in software. The core source code adds a new .compatible of_device_id entry. This is extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The .data entry now holds a reference to the enumerated device type. A new regmap_irq_chip model is added for DA9061 and this supports the new list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the new sub system components for DA9061. Support is added for a new DA9061 regmap_config which lists the correct readable, writable and volatile ranges for this chip. The probe function uses the device tree compatible string to switch on the da9062_compatible_types and configure the correct mfd cells, irq chip and regmap config. Kconfig is updated to reflect support for DA9061 and DA9062 PMICs. Signed-off-by: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> --- Acked-for-mfd-by: Lee Jones <lee.jones@xxxxxxxxxx> Hi Lee, that Ack was from your earlier posting: https://lkml.org/lkml/2017/1/4/328 this was Regards, Steve. This patch applies against linux-next and v4.11-rc3 v5 -> v6 - Rebased from v4.9 to v4.11-rc3 - Modify Copyright to match Dialog latest legal statement - Fixed "braces {} should be used on all arms" checkpatch warning v4 -> v5 - NO CODE CHANGE - Rebased from v4.8 to v4.9 v3 -> v4 - Patch renamed from [PATCH V3 5/9] to [PATCH V4 4/8] - Removed DEFINE_RES_NAMED() macros for DA9061 resources and replaced them with DEFINE_RES_IRQ_NAMED(). - Removed whitespace - Reverted change for badly defined mfd_cell da9062_devs of_compatible string from "dlg,da9062-watchdog" back to "dlg,da9062-wdt" v2 -> v3 - NO CODE CHANGE - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9] v1 -> v2 - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these changes were made to fix checkpatch warnings caused by the patch set dependency order - Fixed typo in the commit message "readble" to "readable" - Removed the explicit cross-check to decide if there is a conflict between the device tree compatible string and the hardware definition. This patch assumes the device tree is correctly written and therefore removes the need for a hardware/DT sanity check. - Removed extra semicolon in drivers/mfd/da9062-core.c:877 - Re-write compatible entries into numerical order Lee, Changes as described in the version history above. As previously: This patch adds support for the DA9061 PMIC. This is done as part of the existing DA9062 device driver by extending the of_device_id match table. This in turn allows new MFD cells, irq chip and regmap definitions to support DA9061. Regards, Steve Twiss, Dialog Semiconductor drivers/mfd/Kconfig | 5 +- drivers/mfd/da9062-core.c | 427 +++++++++++++++++++++++++++++++++-- include/linux/mfd/da9062/core.h | 29 ++- include/linux/mfd/da9062/registers.h | 5 +- 4 files changed, 443 insertions(+), 23 deletions(-) diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 55ecdfb..29cc11a 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -263,13 +263,14 @@ config MFD_DA9055 called "da9055" config MFD_DA9062 - tristate "Dialog Semiconductor DA9062 PMIC Support" + tristate "Dialog Semiconductor DA9062/61 PMIC Support" select MFD_CORE select REGMAP_I2C select REGMAP_IRQ depends on I2C help - Say yes here for support for the Dialog Semiconductor DA9062 PMIC. + Say yes here for support for the Dialog Semiconductor DA9061 and + DA9062 PMICs. This includes the I2C driver and core APIs. Additional drivers must be enabled in order to use the functionality of the device. diff --git a/drivers/mfd/da9062-core.c b/drivers/mfd/da9062-core.c index 8f873866..9310eaf 100644 --- a/drivers/mfd/da9062-core.c +++ b/drivers/mfd/da9062-core.c @@ -1,6 +1,6 @@ /* - * Core, IRQ and I2C device driver for DA9062 PMIC - * Copyright (C) 2015 Dialog Semiconductor Ltd. + * Core, IRQ and I2C device driver for DA9061 and DA9062 PMICs + * Copyright (C) 2015-2017 Dialog Semiconductor * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -30,6 +30,70 @@ #define DA9062_REG_EVENT_B_OFFSET 1 #define DA9062_REG_EVENT_C_OFFSET 2 +static struct regmap_irq da9061_irqs[] = { + /* EVENT A */ + [DA9061_IRQ_ONKEY] = { + .reg_offset = DA9062_REG_EVENT_A_OFFSET, + .mask = DA9062AA_M_NONKEY_MASK, + }, + [DA9061_IRQ_WDG_WARN] = { + .reg_offset = DA9062_REG_EVENT_A_OFFSET, + .mask = DA9062AA_M_WDG_WARN_MASK, + }, + [DA9061_IRQ_SEQ_RDY] = { + .reg_offset = DA9062_REG_EVENT_A_OFFSET, + .mask = DA9062AA_M_SEQ_RDY_MASK, + }, + /* EVENT B */ + [DA9061_IRQ_TEMP] = { + .reg_offset = DA9062_REG_EVENT_B_OFFSET, + .mask = DA9062AA_M_TEMP_MASK, + }, + [DA9061_IRQ_LDO_LIM] = { + .reg_offset = DA9062_REG_EVENT_B_OFFSET, + .mask = DA9062AA_M_LDO_LIM_MASK, + }, + [DA9061_IRQ_DVC_RDY] = { + .reg_offset = DA9062_REG_EVENT_B_OFFSET, + .mask = DA9062AA_M_DVC_RDY_MASK, + }, + [DA9061_IRQ_VDD_WARN] = { + .reg_offset = DA9062_REG_EVENT_B_OFFSET, + .mask = DA9062AA_M_VDD_WARN_MASK, + }, + /* EVENT C */ + [DA9061_IRQ_GPI0] = { + .reg_offset = DA9062_REG_EVENT_C_OFFSET, + .mask = DA9062AA_M_GPI0_MASK, + }, + [DA9061_IRQ_GPI1] = { + .reg_offset = DA9062_REG_EVENT_C_OFFSET, + .mask = DA9062AA_M_GPI1_MASK, + }, + [DA9061_IRQ_GPI2] = { + .reg_offset = DA9062_REG_EVENT_C_OFFSET, + .mask = DA9062AA_M_GPI2_MASK, + }, + [DA9061_IRQ_GPI3] = { + .reg_offset = DA9062_REG_EVENT_C_OFFSET, + .mask = DA9062AA_M_GPI3_MASK, + }, + [DA9061_IRQ_GPI4] = { + .reg_offset = DA9062_REG_EVENT_C_OFFSET, + .mask = DA9062AA_M_GPI4_MASK, + }, +}; + +static struct regmap_irq_chip da9061_irq_chip = { + .name = "da9061-irq", + .irqs = da9061_irqs, + .num_irqs = DA9061_NUM_IRQ, + .num_regs = 3, + .status_base = DA9062AA_EVENT_A, + .mask_base = DA9062AA_IRQ_MASK_A, + .ack_base = DA9062AA_EVENT_A, +}; + static struct regmap_irq da9062_irqs[] = { /* EVENT A */ [DA9062_IRQ_ONKEY] = { @@ -102,6 +166,57 @@ .ack_base = DA9062AA_EVENT_A, }; +static struct resource da9061_core_resources[] = { + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_VDD_WARN, "VDD_WARN"), +}; + +static struct resource da9061_regulators_resources[] = { + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_LDO_LIM, "LDO_LIM"), +}; + +static struct resource da9061_thermal_resources[] = { + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_TEMP, "THERMAL"), +}; + +static struct resource da9061_wdt_resources[] = { + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_WDG_WARN, "WD_WARN"), +}; + +static struct resource da9061_onkey_resources[] = { + DEFINE_RES_IRQ_NAMED(DA9061_IRQ_ONKEY, "ONKEY"), +}; + +static const struct mfd_cell da9061_devs[] = { + { + .name = "da9061-core", + .num_resources = ARRAY_SIZE(da9061_core_resources), + .resources = da9061_core_resources, + }, + { + .name = "da9062-regulators", + .num_resources = ARRAY_SIZE(da9061_regulators_resources), + .resources = da9061_regulators_resources, + }, + { + .name = "da9061-watchdog", + .num_resources = ARRAY_SIZE(da9061_wdt_resources), + .resources = da9061_wdt_resources, + .of_compatible = "dlg,da9061-watchdog", + }, + { + .name = "da9061-thermal", + .num_resources = ARRAY_SIZE(da9061_thermal_resources), + .resources = da9061_thermal_resources, + .of_compatible = "dlg,da9061-thermal", + }, + { + .name = "da9061-onkey", + .num_resources = ARRAY_SIZE(da9061_onkey_resources), + .resources = da9061_onkey_resources, + .of_compatible = "dlg,da9061-onkey", + }, +}; + static struct resource da9062_core_resources[] = { DEFINE_RES_NAMED(DA9062_IRQ_VDD_WARN, 1, "VDD_WARN", IORESOURCE_IRQ), }; @@ -200,7 +315,8 @@ static int da9062_clear_fault_log(struct da9062 *chip) static int da9062_get_device_type(struct da9062 *chip) { - int device_id, variant_id, variant_mrc; + int device_id, variant_id, variant_mrc, variant_vrc; + char *type; int ret; ret = regmap_read(chip->regmap, DA9062AA_DEVICE_ID, &device_id); @@ -219,9 +335,23 @@ static int da9062_get_device_type(struct da9062 *chip) return -EIO; } + variant_vrc = (variant_id & DA9062AA_VRC_MASK) >> DA9062AA_VRC_SHIFT; + + switch (variant_vrc) { + case DA9062_PMIC_VARIANT_VRC_DA9061: + type = "DA9061"; + break; + case DA9062_PMIC_VARIANT_VRC_DA9062: + type = "DA9062"; + break; + default: + type = "Unknown"; + break; + } + dev_info(chip->dev, - "Device detected (device-ID: 0x%02X, var-ID: 0x%02X)\n", - device_id, variant_id); + "Device detected (device-ID: 0x%02X, var-ID: 0x%02X, %s)\n", + device_id, variant_id, type); variant_mrc = (variant_id & DA9062AA_MRC_MASK) >> DA9062AA_MRC_SHIFT; @@ -234,6 +364,234 @@ static int da9062_get_device_type(struct da9062 *chip) return ret; } +static const struct regmap_range da9061_aa_readable_ranges[] = { + { + .range_min = DA9062AA_PAGE_CON, + .range_max = DA9062AA_STATUS_B, + }, { + .range_min = DA9062AA_STATUS_D, + .range_max = DA9062AA_EVENT_C, + }, { + .range_min = DA9062AA_IRQ_MASK_A, + .range_max = DA9062AA_IRQ_MASK_C, + }, { + .range_min = DA9062AA_CONTROL_A, + .range_max = DA9062AA_GPIO_4, + }, { + .range_min = DA9062AA_GPIO_WKUP_MODE, + .range_max = DA9062AA_GPIO_OUT3_4, + }, { + .range_min = DA9062AA_BUCK1_CONT, + .range_max = DA9062AA_BUCK4_CONT, + }, { + .range_min = DA9062AA_BUCK3_CONT, + .range_max = DA9062AA_BUCK3_CONT, + }, { + .range_min = DA9062AA_LDO1_CONT, + .range_max = DA9062AA_LDO4_CONT, + }, { + .range_min = DA9062AA_DVC_1, + .range_max = DA9062AA_DVC_1, + }, { + .range_min = DA9062AA_SEQ, + .range_max = DA9062AA_ID_4_3, + }, { + .range_min = DA9062AA_ID_12_11, + .range_max = DA9062AA_ID_16_15, + }, { + .range_min = DA9062AA_ID_22_21, + .range_max = DA9062AA_ID_32_31, + }, { + .range_min = DA9062AA_SEQ_A, + .range_max = DA9062AA_WAIT, + }, { + .range_min = DA9062AA_RESET, + .range_max = DA9062AA_BUCK_ILIM_C, + }, { + .range_min = DA9062AA_BUCK1_CFG, + .range_max = DA9062AA_BUCK3_CFG, + }, { + .range_min = DA9062AA_VBUCK1_A, + .range_max = DA9062AA_VBUCK4_A, + }, { + .range_min = DA9062AA_VBUCK3_A, + .range_max = DA9062AA_VBUCK3_A, + }, { + .range_min = DA9062AA_VLDO1_A, + .range_max = DA9062AA_VLDO4_A, + }, { + .range_min = DA9062AA_VBUCK1_B, + .range_max = DA9062AA_VBUCK4_B, + }, { + .range_min = DA9062AA_VBUCK3_B, + .range_max = DA9062AA_VBUCK3_B, + }, { + .range_min = DA9062AA_VLDO1_B, + .range_max = DA9062AA_VLDO4_B, + }, { + .range_min = DA9062AA_BBAT_CONT, + .range_max = DA9062AA_BBAT_CONT, + }, { + .range_min = DA9062AA_INTERFACE, + .range_max = DA9062AA_CONFIG_E, + }, { + .range_min = DA9062AA_CONFIG_G, + .range_max = DA9062AA_CONFIG_K, + }, { + .range_min = DA9062AA_CONFIG_M, + .range_max = DA9062AA_CONFIG_M, + }, { + .range_min = DA9062AA_GP_ID_0, + .range_max = DA9062AA_GP_ID_19, + }, { + .range_min = DA9062AA_DEVICE_ID, + .range_max = DA9062AA_CONFIG_ID, + }, +}; + +static const struct regmap_range da9061_aa_writeable_ranges[] = { + { + .range_min = DA9062AA_PAGE_CON, + .range_max = DA9062AA_PAGE_CON, + }, { + .range_min = DA9062AA_FAULT_LOG, + .range_max = DA9062AA_EVENT_C, + }, { + .range_min = DA9062AA_IRQ_MASK_A, + .range_max = DA9062AA_IRQ_MASK_C, + }, { + .range_min = DA9062AA_CONTROL_A, + .range_max = DA9062AA_GPIO_4, + }, { + .range_min = DA9062AA_GPIO_WKUP_MODE, + .range_max = DA9062AA_GPIO_OUT3_4, + }, { + .range_min = DA9062AA_BUCK1_CONT, + .range_max = DA9062AA_BUCK4_CONT, + }, { + .range_min = DA9062AA_BUCK3_CONT, + .range_max = DA9062AA_BUCK3_CONT, + }, { + .range_min = DA9062AA_LDO1_CONT, + .range_max = DA9062AA_LDO4_CONT, + }, { + .range_min = DA9062AA_DVC_1, + .range_max = DA9062AA_DVC_1, + }, { + .range_min = DA9062AA_SEQ, + .range_max = DA9062AA_ID_4_3, + }, { + .range_min = DA9062AA_ID_12_11, + .range_max = DA9062AA_ID_16_15, + }, { + .range_min = DA9062AA_ID_22_21, + .range_max = DA9062AA_ID_32_31, + }, { + .range_min = DA9062AA_SEQ_A, + .range_max = DA9062AA_WAIT, + }, { + .range_min = DA9062AA_RESET, + .range_max = DA9062AA_BUCK_ILIM_C, + }, { + .range_min = DA9062AA_BUCK1_CFG, + .range_max = DA9062AA_BUCK3_CFG, + }, { + .range_min = DA9062AA_VBUCK1_A, + .range_max = DA9062AA_VBUCK4_A, + }, { + .range_min = DA9062AA_VBUCK3_A, + .range_max = DA9062AA_VBUCK3_A, + }, { + .range_min = DA9062AA_VLDO1_A, + .range_max = DA9062AA_VLDO4_A, + }, { + .range_min = DA9062AA_VBUCK1_B, + .range_max = DA9062AA_VBUCK4_B, + }, { + .range_min = DA9062AA_VBUCK3_B, + .range_max = DA9062AA_VBUCK3_B, + }, { + .range_min = DA9062AA_VLDO1_B, + .range_max = DA9062AA_VLDO4_B, + }, { + .range_min = DA9062AA_BBAT_CONT, + .range_max = DA9062AA_BBAT_CONT, + }, { + .range_min = DA9062AA_GP_ID_0, + .range_max = DA9062AA_GP_ID_19, + }, +}; + +static const struct regmap_range da9061_aa_volatile_ranges[] = { + { + .range_min = DA9062AA_PAGE_CON, + .range_max = DA9062AA_STATUS_B, + }, { + .range_min = DA9062AA_STATUS_D, + .range_max = DA9062AA_EVENT_C, + }, { + .range_min = DA9062AA_CONTROL_A, + .range_max = DA9062AA_CONTROL_B, + }, { + .range_min = DA9062AA_CONTROL_E, + .range_max = DA9062AA_CONTROL_F, + }, { + .range_min = DA9062AA_BUCK1_CONT, + .range_max = DA9062AA_BUCK4_CONT, + }, { + .range_min = DA9062AA_BUCK3_CONT, + .range_max = DA9062AA_BUCK3_CONT, + }, { + .range_min = DA9062AA_LDO1_CONT, + .range_max = DA9062AA_LDO4_CONT, + }, { + .range_min = DA9062AA_DVC_1, + .range_max = DA9062AA_DVC_1, + }, { + .range_min = DA9062AA_SEQ, + .range_max = DA9062AA_SEQ, + }, +}; + +static const struct regmap_access_table da9061_aa_readable_table = { + .yes_ranges = da9061_aa_readable_ranges, + .n_yes_ranges = ARRAY_SIZE(da9061_aa_readable_ranges), +}; + +static const struct regmap_access_table da9061_aa_writeable_table = { + .yes_ranges = da9061_aa_writeable_ranges, + .n_yes_ranges = ARRAY_SIZE(da9061_aa_writeable_ranges), +}; + +static const struct regmap_access_table da9061_aa_volatile_table = { + .yes_ranges = da9061_aa_volatile_ranges, + .n_yes_ranges = ARRAY_SIZE(da9061_aa_volatile_ranges), +}; + +static const struct regmap_range_cfg da9061_range_cfg[] = { + { + .range_min = DA9062AA_PAGE_CON, + .range_max = DA9062AA_CONFIG_ID, + .selector_reg = DA9062AA_PAGE_CON, + .selector_mask = 1 << DA9062_I2C_PAGE_SEL_SHIFT, + .selector_shift = DA9062_I2C_PAGE_SEL_SHIFT, + .window_start = 0, + .window_len = 256, + } +}; + +static struct regmap_config da9061_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .ranges = da9061_range_cfg, + .num_ranges = ARRAY_SIZE(da9061_range_cfg), + .max_register = DA9062AA_CONFIG_ID, + .cache_type = REGCACHE_RBTREE, + .rd_table = &da9061_aa_readable_table, + .wr_table = &da9061_aa_writeable_table, + .volatile_table = &da9061_aa_volatile_table, +}; + static const struct regmap_range da9062_aa_readable_ranges[] = { { .range_min = DA9062AA_PAGE_CON, @@ -456,17 +814,39 @@ static int da9062_get_device_type(struct da9062 *chip) .volatile_table = &da9062_aa_volatile_table, }; +static const struct of_device_id da9062_dt_ids[] = { + { .compatible = "dlg,da9061", .data = (void *)COMPAT_TYPE_DA9061, }, + { .compatible = "dlg,da9062", .data = (void *)COMPAT_TYPE_DA9062, }, + { } +}; +MODULE_DEVICE_TABLE(of, da9062_dt_ids); + static int da9062_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct da9062 *chip; + const struct of_device_id *match; unsigned int irq_base; + const struct mfd_cell *cell; + const struct regmap_irq_chip *irq_chip; + const struct regmap_config *config; + int cell_num; int ret; chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL); if (!chip) return -ENOMEM; + if (i2c->dev.of_node) { + match = of_match_node(da9062_dt_ids, i2c->dev.of_node); + if (!match) + return -EINVAL; + + chip->chip_type = (int)match->data; + } else { + chip->chip_type = id->driver_data; + } + i2c_set_clientdata(i2c, chip); chip->dev = &i2c->dev; @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c, return -EINVAL; } - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config); + switch (chip->chip_type) { + case(COMPAT_TYPE_DA9061): + cell = da9061_devs; + cell_num = ARRAY_SIZE(da9061_devs); + irq_chip = &da9061_irq_chip; + config = &da9061_regmap_config; + break; + case(COMPAT_TYPE_DA9062): + cell = da9062_devs; + cell_num = ARRAY_SIZE(da9062_devs); + irq_chip = &da9062_irq_chip; + config = &da9062_regmap_config; + break; + default: + dev_err(chip->dev, "Unrecognised chip type\n"); + return -ENODEV; + } + + chip->regmap = devm_regmap_init_i2c(i2c, config); if (IS_ERR(chip->regmap)) { ret = PTR_ERR(chip->regmap); dev_err(chip->dev, "Failed to allocate register map: %d\n", @@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c, ret = regmap_add_irq_chip(chip->regmap, i2c->irq, IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED, - -1, &da9062_irq_chip, + -1, irq_chip, &chip->regmap_irq); if (ret) { dev_err(chip->dev, "Failed to request IRQ %d: %d\n", @@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c, irq_base = regmap_irq_chip_get_base(chip->regmap_irq); - ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs, - ARRAY_SIZE(da9062_devs), NULL, irq_base, + ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell, + cell_num, NULL, irq_base, NULL); if (ret) { dev_err(chip->dev, "Cannot register child devices\n"); @@ -526,17 +924,12 @@ static int da9062_i2c_remove(struct i2c_client *i2c) } static const struct i2c_device_id da9062_i2c_id[] = { - { "da9062", 0 }, + { "da9061", COMPAT_TYPE_DA9061 }, + { "da9062", COMPAT_TYPE_DA9062 }, { }, }; MODULE_DEVICE_TABLE(i2c, da9062_i2c_id); -static const struct of_device_id da9062_dt_ids[] = { - { .compatible = "dlg,da9062", }, - { } -}; -MODULE_DEVICE_TABLE(of, da9062_dt_ids); - static struct i2c_driver da9062_i2c_driver = { .driver = { .name = "da9062", @@ -549,6 +942,6 @@ static int da9062_i2c_remove(struct i2c_client *i2c) module_i2c_driver(da9062_i2c_driver); -MODULE_DESCRIPTION("Core device driver for Dialog DA9062"); +MODULE_DESCRIPTION("Core device driver for Dialog DA9061 and DA9062"); MODULE_AUTHOR("Steve Twiss <stwiss.opensource@xxxxxxxxxxx>"); MODULE_LICENSE("GPL"); diff --git a/include/linux/mfd/da9062/core.h b/include/linux/mfd/da9062/core.h index 376ba84..74d33a0 100644 --- a/include/linux/mfd/da9062/core.h +++ b/include/linux/mfd/da9062/core.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2015 Dialog Semiconductor Ltd. + * Copyright (C) 2015-2017 Dialog Semiconductor * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -18,7 +18,31 @@ #include <linux/interrupt.h> #include <linux/mfd/da9062/registers.h> -/* Interrupts */ +enum da9062_compatible_types { + COMPAT_TYPE_DA9061 = 1, + COMPAT_TYPE_DA9062, +}; + +enum da9061_irqs { + /* IRQ A */ + DA9061_IRQ_ONKEY, + DA9061_IRQ_WDG_WARN, + DA9061_IRQ_SEQ_RDY, + /* IRQ B*/ + DA9061_IRQ_TEMP, + DA9061_IRQ_LDO_LIM, + DA9061_IRQ_DVC_RDY, + DA9061_IRQ_VDD_WARN, + /* IRQ C */ + DA9061_IRQ_GPI0, + DA9061_IRQ_GPI1, + DA9061_IRQ_GPI2, + DA9061_IRQ_GPI3, + DA9061_IRQ_GPI4, + + DA9061_NUM_IRQ, +}; + enum da9062_irqs { /* IRQ A */ DA9062_IRQ_ONKEY, @@ -45,6 +69,7 @@ struct da9062 { struct device *dev; struct regmap *regmap; struct regmap_irq_chip_data *regmap_irq; + enum da9062_compatible_types chip_type; }; #endif /* __MFD_DA9062_CORE_H__ */ diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h index 97790d1..18d576a 100644 --- a/include/linux/mfd/da9062/registers.h +++ b/include/linux/mfd/da9062/registers.h @@ -1,6 +1,5 @@ /* - * registers.h - REGISTERS H for DA9062 - * Copyright (C) 2015 Dialog Semiconductor Ltd. + * Copyright (C) 2015-2017 Dialog Semiconductor * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -18,6 +17,8 @@ #define DA9062_PMIC_DEVICE_ID 0x62 #define DA9062_PMIC_VARIANT_MRC_AA 0x01 +#define DA9062_PMIC_VARIANT_VRC_DA9061 0x01 +#define DA9062_PMIC_VARIANT_VRC_DA9062 0x02 #define DA9062_I2C_PAGE_SEL_SHIFT 1 -- end-of-patch for PATCH V6 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
