On Fri, Mar 24, 2017 at 12:55 PM, Shawn Guo <shawnguo@xxxxxxxxxx> wrote: > On Fri, Mar 24, 2017 at 12:29:49PM +0530, Jagan Teki wrote: >> On Fri, Mar 24, 2017 at 10:46 AM, Shawn Guo <shawnguo@xxxxxxxxxx> wrote: >> > On Wed, Mar 22, 2017 at 11:18:10PM +0530, Jagan Teki wrote: >> >> From: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx> >> >> >> >> Add touchscreen node as i2c1 slave device on Engicam Is.IoT MX6UL >> >> modules, the touchscreen controlled 'st,stmpe-ts' connected via >> >> i2c with st,stmpe811 mfb interface. >> > >> > s/mfb/mfd? >> > >> >> >> >> Cc: Shawn Guo <shawnguo@xxxxxxxxxx> >> >> Cc: Matteo Lisi <matteo.lisi@xxxxxxxxxxx> >> >> Cc: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx> >> >> Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx> >> >> --- >> >> arch/arm/boot/dts/imx6ul-isiot-common.dtsi | 34 ++++++++++++++++++++++++++++++ >> >> 1 file changed, 34 insertions(+) >> >> >> >> diff --git a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi >> >> index 9660e20..b149b5e 100644 >> >> --- a/arch/arm/boot/dts/imx6ul-isiot-common.dtsi >> >> +++ b/arch/arm/boot/dts/imx6ul-isiot-common.dtsi >> >> @@ -40,6 +40,34 @@ >> >> * OTHER DEALINGS IN THE SOFTWARE. >> >> */ >> >> >> >> +&i2c1 { >> >> + touch: stmpe811@44 { >> > >> > Label a MFD device 'touch'? Also, the node name should be generic. Not >> > sure what should be used for MFD device though. >> >> May be I can use stmpe811@41 the existing imx6qdl-apalis.dtsi using >> the similar notation. > > Per application notes of stmpe811 below, I would suggest you name it > gpio-expander. > > www.st.com/resource/zh/datasheet/CD00186725.pdf OK, will this be ok? stmpe811: gpio-expander@44 { > >> >> > >> >> + compatible = "st,stmpe811"; >> >> + reg = <0x44>; >> >> + #address-cells = <1>; >> >> + #size-cells = <0>; >> >> + pinctrl-names = "default"; >> >> + pinctrl-0 = <&pinctrl_stmpe_ts>; >> > >> > If this is for stmpe-ts, shouldn't be put into touchscreen child node? >> >> Actually this is interrupt pad, for the touch controller via stmpe so >> I can rename pinctrl_touch_int. > > Or just pinctrl_stmpe. > >> >> > >> >> + interrupt-parent = <&gpio1>; >> >> + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; >> >> + interrupt-controller; >> >> + #interrupt-cells = <2>; >> >> + >> >> + stmpe_touchscreen { >> > >> > 'stmpe: touchscreen {' might be better. >> >> stmpe_touchscreen { >> >> This is also compatible with existing dtsi files > > We do not need to keep compatibility with something not good. thanks! -- Jagan Teki Senior Linux Kernel Engineer | Amarula Solutions U-Boot, Linux | Upstream Maintainer Hyderabad, India. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html