Re: [PATCH v3 2/4] arm64: dts: rockchip: add Gru/Kevin DTS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




2017-03-21 0:53 GMT+01:00 Brian Norris <briannorris@xxxxxxxxxxxx>:
> Kevin is part of a family of boards called Gru. As best as possible, the
> properties shared by the Gru family are placed in rk3399-gru.dtsi, while
> Kevin-specific bits are in rk3399-gru-kevin.dts. This does not add full
> support for the base Gru board.
>
> Working and tested (to some extent):
>  * EC support -- including keyboard, battery, PWM, and probably more
>  * UART / console
>  * Thermal
>  * Touchscreen
>  * Touchpad
>  * Digitizer (regulator still WIP)
>  * PCIe / Wifi
>  * Bluetooth / Webcam
>  * SD card
>  * eMMC
>  * USB2 on TypeC
>    - This works much of the time, but USB3 devices may or may not detect
>      properly. Waiting on proper extcon support for USB3 over TypeC.
>    - Depends on XHCI/DWC3 fixes for ARM64 that still haven't landed
>  * Backlight
>
> Not working:
>  * CPUFreq -- relies on special OVP support for our PWM regulator
>    circuits
>  * EC / extcon support -- and with it, USB3/TypeC/DP
>  * DRM -- won't even build on ARM64, so all display, eDP, etc. is not
>    enabled
>
> Not tested:
>  * Audio
>
> Signed-off-by: Brian Norris <briannorris@xxxxxxxxxxxx>
> ---
> v2 -> v3:
>  * reference {pmu-,}io-domain nodes from main rk3399.dtsi
>  * drop some now-superfluous comments
>  * use new proposed '#include <arm/...>' DTSI include path (symlink)
>
> v1 -> v2:
>  * drop deprecated da7219 'dlg,ldo-lvl' property
>  * update copyrights
>  * adjust GPLL to 600 MHz
>  * drop PCIe link speed overrides (they're in rk3399.dtsi now)
>  * fix spi1 leakage with "sleep" state pinctrl
>  * drop unneeded "google,cros-ec-spi-pre-delay"
> ---
>  arch/arm64/boot/dts/rockchip/Makefile             |   1 +
>  arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts | 312 +++++++
>  arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi      | 988 ++++++++++++++++++++++
>  3 files changed, 1301 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 3a862894ea44..b82f7b61ab6f 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
>
>  always         := $(dtb-y)
>  subdir-y       := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
> new file mode 100644
> index 000000000000..2f720cf2fd07
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
> @@ -0,0 +1,312 @@
> +/*
> + * Google Gru-Kevin Rev 6+ board device tree source
> + *
> + * Copyright 2016-2017 Google, Inc
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *  Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "rk3399-gru.dtsi"
> +#include <include/dt-bindings/input/linux-event-codes.h>
> +
> +/*
> + * Kevin-specific things
> + *
> + * Things in this section should use names from Kevin schematic since no
> + * equivalent exists in Gru schematic.  If referring to signals that exist
> + * in Gru we use the Gru names, though.  Confusing enough for you?
> + */
> +/ {
> +       model = "Google Kevin";
> +       compatible = "google,kevin-rev15", "google,kevin-rev14",
> +                    "google,kevin-rev13", "google,kevin-rev12",
> +                    "google,kevin-rev11", "google,kevin-rev10",
> +                    "google,kevin-rev9", "google,kevin-rev8",
> +                    "google,kevin-rev7", "google,kevin-rev6",
> +                    "google,kevin", "google,gru", "rockchip,rk3399";
> +
> +       /* Power tree */
> +
> +       /* pp3300 children */
> +
> +       p3_3v_dig: p3-3v-dig {
> +               compatible = "regulator-fixed";
> +               regulator-name = "p3.3v_dig";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&cpu3_pen_pwr_en>;
> +
> +               enable-active-high;
> +               gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
> +               vin-supply = <&pp3300>;
> +       };
> +
> +       /* END REGULATORS */
> +
> +       backlight: backlight {
> +               compatible = "pwm-backlight";
> +               pwms = <&cros_ec_pwm 1>;
> +               brightness-levels = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
> +                                    17 18 19 20 21 22 23 24 25 26 27 28 29 30
> +                                    31 32 33 34 35 36 37 38 39 40 41 42 43 44
> +                                    45 46 47 48 49 50 51 52 53 54 55 56 57 58
> +                                    59 60 61 62 63 64 65 66 67 68 69 70 71 72
> +                                    73 74 75 76 77 78 79 80 81 82 83 84 85 86
> +                                    87 88 89 90 91 92 93 94 95 96 97 98 99 100>;
> +               default-brightness-level = <51>;
> +               enable-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> +               power-supply = <&pp3300_disp>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&bl_en>;
> +               pwm-delay-us = <10000>;
> +       };
> +
> +       thermistor_ppvar_bigcpu: thermistor-ppvar-bigcpu {
> +               compatible = "murata,ncp15wb473";
> +               pullup-uv = <1800000>;
> +               pullup-ohm = <25500>;
> +               pulldown-ohm = <0>;
> +               io-channels = <&saradc 2>;
> +               #thermal-sensor-cells = <0>;
> +       };
> +
> +       thermistor_ppvar_litcpu: thermistor-ppvar-litcpu {
> +               compatible = "murata,ncp15wb473";
> +               pullup-uv = <1800000>;
> +               pullup-ohm = <25500>;
> +               pulldown-ohm = <0>;
> +               io-channels = <&saradc 3>;
> +               #thermal-sensor-cells = <0>;
> +       };
> +};
> +
> +&gpio_keys {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>;
> +
> +       pen-insert {
> +               label = "Pen Insert";
> +               /* Insert = low, eject = high */
> +               gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
> +               linux,code = <SW_PEN_INSERTED>;
> +               linux,input-type = <EV_SW>;
> +               wakeup-source;
> +       };
> +};
> +
> +&thermal_zones {
> +       bigcpu_reg_thermal: bigcpu-reg-thermal {
> +               polling-delay-passive = <100>; /* milliseconds */
> +               polling-delay = <1000>; /* milliseconds */
> +               thermal-sensors = <&thermistor_ppvar_bigcpu 0>;
> +               sustainable-power = <4000>;
> +
> +               ppvar_bigcpu_trips: trips {
> +                       ppvar_bigcpu_on: ppvar-bigcpu-on {
> +                               temperature = <40000>;  /* millicelsius */
> +                               hysteresis = <2000>;    /* millicelsius */
> +                               type = "passive";
> +                       };
> +
> +                       ppvar_bigcpu_alert: ppvar-bigcpu-alert {
> +                               temperature = <50000>;  /* millicelsius */
> +                               hysteresis = <2000>;    /* millicelsius */
> +                               type = "passive";
> +                       };
> +
> +                       ppvar_bigcpu_crit: ppvar-bigcpu-crit {
> +                               temperature = <90000>;  /* millicelsius */
> +                               hysteresis = <0>;       /* millicelsius */
> +                               type = "critical";
> +                       };
> +               };
> +
> +               cooling-maps {
> +                       map0 {
> +                               trip = <&ppvar_bigcpu_alert>;
> +                               cooling-device =
> +                                       <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +                               contribution = <4096>;
> +                       };
> +                       map1 {
> +                               trip = <&ppvar_bigcpu_alert>;
> +                               cooling-device =
> +                                       <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +                               contribution = <1024>;
> +                       };
> +               };
> +       };
> +
> +       litcpu_reg_thermal: litcpu-reg-thermal {
> +               polling-delay-passive = <100>; /* milliseconds */
> +               polling-delay = <1000>; /* milliseconds */
> +               thermal-sensors = <&thermistor_ppvar_litcpu 0>;
> +               sustainable-power = <4000>;
> +
> +               ppvar_litcpu_trips: trips {
> +                       ppvar_litcpu_on: ppvar-litcpu-on {
> +                               temperature = <40000>;  /* millicelsius */
> +                               hysteresis = <2000>;    /* millicelsius */
> +                               type = "passive";
> +                       };
> +
> +                       ppvar_litcpu_alert: ppvar-litcpu-alert {
> +                               temperature = <50000>;  /* millicelsius */
> +                               hysteresis = <2000>;    /* millicelsius */
> +                               type = "passive";
> +                       };
> +
> +                       ppvar_litcpu_crit: ppvar-litcpu-crit {
> +                               temperature = <90000>;  /* millicelsius */
> +                               hysteresis = <0>;       /* millicelsius */
> +                               type = "critical";
> +                       };
> +               };
> +       };
> +};
> +
> +ap_i2c_tpm: &i2c0 {
> +       status = "okay";
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times. */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +
> +       tpm: tpm@20 {
> +               compatible = "infineon,slb9645tt";
> +               reg = <0x20>;
> +               powered-while-suspended;
> +       };
> +};
> +
> +ap_i2c_dig: &i2c2 {
> +       status = "okay";
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times. */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +
> +       digitizer: digitizer@9 {
> +               compatible = "hid-over-i2c";
> +               reg = <0x9>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&cpu1_dig_irq_l &cpu1_dig_pdct_l>;
> +
> +               interrupt-parent = <&gpio2>;
> +               interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> +
> +               hid-descr-addr = <0x1>;
> +       };
> +};
> +
> +/* Adjustments to things in the gru baseboard */
> +
> +&ap_i2c_tp {
> +       trackpad@4a {
> +               compatible = "atmel,atmel_mxt_tp";
> +               reg = <0x4a>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&trackpad_int_l>;
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> +               wakeup-source;
> +       };
> +};
> +
> +&ap_i2c_ts {
> +       touchscreen@4b {
> +               compatible = "atmel,atmel_mxt_ts";
> +               reg = <0x4b>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&touch_int_l>;
> +               interrupt-parent = <&gpio3>;
> +               interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
> +       };
> +};
> +
> +&saradc {
> +       status = "okay";
> +       vref-supply = <&pp1800_ap_io>;
> +};
> +
> +&mvl_wifi {
> +       marvell,wakeup-pin = <14>; /* GPIO_14 on Marvell */
> +};
> +
> +/* PINCTRL: always below everything else */
> +
> +&pinctrl {
> +       digitizer {
> +               /* Has external pullup */
> +               cpu1_dig_irq_l: cpu1-dig-irq-l {
> +                       rockchip,pins = <2 4 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +
> +               /* Has external pullup */
> +               cpu1_dig_pdct_l: cpu1-dig-pdct-l {
> +                       rockchip,pins = <2 5 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +
> +       discrete-regulators {
> +               cpu3_pen_pwr_en: cpu3-pen-pwr-en {
> +                       rockchip,pins = <4 30 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +
> +       pen {
> +               cpu1_pen_eject: cpu1-pen-eject {
> +                       rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +       };
> +
> +       wifi {
> +               wlan_host_wake_l: wlan-host-wake-l {
> +                       rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +};
> +
> +/* DON'T PUT ANYTHING BELOW HERE.  PUT IT ABOVE PINCTRL */
> +/* DON'T PUT ANYTHING BELOW HERE.  PUT IT ABOVE PINCTRL */
> +/* DON'T PUT ANYTHING BELOW HERE.  PUT IT ABOVE PINCTRL */
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> new file mode 100644
> index 000000000000..9c581173cb64
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
> @@ -0,0 +1,988 @@
> +/*
> + * Google Gru (and derivatives) board device tree source
> + *
> + * Copyright 2016-2017 Google, Inc
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + *  Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include "rk3399.dtsi"
> +
> +/ {
> +       chosen {
> +               stdout-path = "serial2:115200n8";
> +       };
> +
> +       /*
> +        * Power Tree
> +        *
> +        * In general an attempt is made to include all rails called out by
> +        * the schematic as long as those rails interact in some way with
> +        * the AP.  AKA:
> +        * - Rails that only connect to the EC (or devices that the EC talks to)
> +        *   are not included.
> +        * - Rails _are_ included if the rails go to the AP even if the AP
> +        *   doesn't currently care about them / they are always on.  The idea
> +        *   here is that it makes it easier to map to the schematic or extend
> +        *   later.
> +        *
> +        * If two rails are substantially the same from the AP's point of
> +        * view, though, we won't create a full fixed regulator.  We'll just
> +        * put the child rail as an alias of the parent rail.  Sometimes rails
> +        * look the same to the AP because one of these is true:
> +        * - The EC controls the enable and the EC always enables a rail as
> +        *   long as the AP is running.
> +        * - The rails are actually connected to each other by a jumper and
> +        *   the distinction is just there to add clarity/flexibility to the
> +        *   schematic.
> +        */
> +
> +       /* parentless regulators */
> +
> +       ppvar_sys: ppvar-sys {
> +               compatible = "regulator-fixed";
> +               regulator-name = "ppvar_sys";
> +               regulator-always-on;
> +               regulator-boot-on;
> +       };
> +
> +       pp900_ap: pp900-ap {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp900_ap";
> +
> +               /* EC turns on w/ pp900_ap_en; always on for AP */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <900000>;
> +               regulator-max-microvolt = <900000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       pp1200_lpddr: pp1200-lpddr {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp1200_lpddr";
> +
> +               /* EC turns on w/ lpddr_pwr_en; always on for AP */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <1200000>;
> +               regulator-max-microvolt = <1200000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       pp1800: pp1800 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp1800";
> +
> +               /* Always on when ppvar_sys shows power good */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       pp3000: pp3000 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3000";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pp3000_en>;
> +
> +               enable-active-high;
> +               gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> +
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <3000000>;
> +               regulator-max-microvolt = <3000000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       pp3300: pp3300 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3300";
> +
> +               /* Always on; plain and simple */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       pp5000: pp5000 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp5000";
> +
> +               /* EC turns on w/ pp5000_en; always on for AP */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       /* Schematics call this PPVAR even though it's fixed */
> +       ppvar_logic: ppvar-logic {
> +               compatible = "regulator-fixed";
> +               regulator-name = "ppvar_logic";
> +
> +               /* EC turns on w/ ppvar_logic_en; always on for AP */
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               regulator-min-microvolt = <900000>;
> +               regulator-max-microvolt = <900000>;
> +
> +               vin-supply = <&ppvar_sys>;
> +       };
> +
> +       /* EC turns on w/ pp900_ddrpll_en */
> +       pp900_ddrpll: pp900-ap {
> +       };
> +
> +       /* EC turns on w/ pp900_pcie_en */
> +       pp900_pcie: pp900-ap {
> +       };
> +
> +       /* EC turns on w/ pp900_pll_en */
> +       pp900_pll: pp900-ap {
> +       };
> +
> +       /* EC turns on w/ pp900_pmu_en */
> +       pp900_pmu: pp900-ap {
> +       };
> +
> +       /* EC turns on w/ pp900_usb_en */
> +       pp900_usb: pp900-ap {
> +       };
> +
> +       /* EC turns on w/ pp1800_s0_en_l */
> +       pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
> +       };
> +
> +       /* EC turns on w/ pp1800_avdd_en_l */
> +       pp1800_avdd: pp1800 {
> +       };
> +
> +       /* EC turns on w/ pp1800_lid_en_l */
> +       pp1800_lid: pp1800_mic: pp1800 {
> +       };
> +
> +       /* EC turns on w/ lpddr_pwr_en */
> +       pp1800_lpddr: pp1800 {
> +       };
> +
> +       /* EC turns on w/ pp1800_pmu_en_l */
> +       pp1800_pmu: pp1800 {
> +       };
> +
> +       /* EC turns on w/ pp1800_usb_en_l */
> +       pp1800_usb: pp1800 {
> +       };
> +
> +       pp1500_ap_io: pp1500-ap-io {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp1500_ap_io";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pp1500_en>;
> +
> +               enable-active-high;
> +               gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
> +
> +               regulator-always-on;
> +               regulator-boot-on;
> +               regulator-min-microvolt = <1500000>;
> +               regulator-max-microvolt = <1500000>;
> +
> +               vin-supply = <&pp1800>;
> +       };
> +
> +       pp1800_audio: pp1800-audio {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp1800_audio";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pp1800_audio_en>;
> +
> +               regulator-always-on;
> +               regulator-boot-on;
> +
> +               enable-active-high;
> +               gpio = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> +
> +               vin-supply = <&pp1800>;
> +       };
> +
> +       pp1800_pcie: pp1800-pcie {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp1800_pcie";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&wlan_module_pd_l>;
> +
> +               /*
> +                * Need to wait 1ms + ramp-up time before we can power on WiFi.
> +                * This has been approximated as 8ms total.
> +                */
> +               regulator-enable-ramp-delay = <8000>;
> +
> +               enable-active-high;
> +               gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> +
> +               vin-supply = <&pp1800>;
> +       };
> +
> +       /*
> +        * This is a bit of a hack. The WiFi module should be reset at least
> +        * 1ms after its regulators have ramped up (max rampup time is ~7ms).
> +        * With some stretching of the imagination, we can call the 1.8V
> +        * regulator a supply.
> +        */
> +       wlan_pd_n: wlan-pd-n {
> +               compatible = "regulator-fixed";
> +               regulator-name = "wlan_pd_n";
> +
> +               /* Note the wlan_module_reset_l pinctrl */
> +               enable-active-high;
> +               gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
> +
> +               vin-supply = <&pp1800_pcie>;
> +       };
> +
> +       /* Always on; plain and simple */
> +       pp3000_ap: pp3000_emmc: pp3000 {
> +       };
> +
> +       pp3000_sd_slot: pp3000-sd-slot {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3000_sd_slot";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&sd_slot_pwr_en>;
> +
> +               enable-active-high;
> +               gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
> +
> +               vin-supply = <&pp3000>;
> +       };
> +
> +       /*
> +        * Technically, this is a small abuse of 'regulator-gpio'; this
> +        * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
> +        * always on though, so it is sufficient to simply control the mux
> +        * here.
> +        */
> +       ppvar_sd_card_io: ppvar-sd-card-io {
> +               compatible = "regulator-gpio";
> +               regulator-name = "ppvar_sd_card_io";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
> +
> +               enable-active-high;
> +               enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> +               gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
> +               states = <1800000 0x1
> +                         3000000 0x0>;
> +
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <3000000>;
> +       };
> +
> +       /* EC turns on w/ pp3300_trackpad_en_l */
> +       pp3300_trackpad: pp3300-trackpad {
> +       };
> +
> +       /* EC turns on w/ pp3300_usb_en_l */
> +       pp3300_usb: pp3300 {
> +       };
> +
> +       pp3300_disp: pp3300-disp {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3300_disp";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pp3300_disp_en>;
> +
> +               enable-active-high;
> +
> +               gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +
> +               startup-delay-us = <2000>;
> +               vin-supply = <&pp3300>;
> +       };
> +
> +       pp3300_wifi_bt: pp3300-wifi-bt {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3300_wifi_bt";
> +               /* NOTE: wlan_module_pd_l pinctrl in pp1800_pcie */
> +
> +               enable-active-high;
> +
> +               /* NOTE: this GPIO also used in pp1800_pcie */
> +               gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> +
> +               vin-supply = <&pp3300>;
> +       };
> +
> +       /* EC turns on w/ usb_a_en */
> +       pp5000_usb_a_vbus: pp5000 {
> +       };
> +
> +       max98357a: max98357a {
> +               #sound-dai-cells = <0>;
> +               status = "okay";
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&sdmode_en>;
> +
> +               compatible = "maxim,max98357a";
> +               sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> +               sdmode-delay = <2>;
> +       };
> +
> +       sound {
> +               compatible = "rockchip,rk3399-gru-sound";
> +               rockchip,cpu = <&i2s0 &i2s2>;
> +               rockchip,codec = <&max98357a &headsetcodec &codec>;
> +       };
> +
> +       gpio_keys: gpio-keys {
> +               compatible = "gpio-keys";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&bt_host_wake_l>;
> +
> +               wake-on-bt {
> +                       label = "Wake-on-Bluetooth";
> +                       gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
> +                       linux,code = <KEY_WAKEUP>;
> +                       wakeup-source;
> +               };
> +       };
> +};
> +
> +&cru {
> +       assigned-clocks =
> +               <&cru PLL_GPLL>, <&cru PLL_CPLL>,
> +               <&cru PLL_NPLL>,
> +               <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
> +               <&cru PCLK_PERIHP>,
> +               <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
> +               <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
> +               <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
> +       assigned-clock-rates =
> +               <600000000>, <800000000>,
> +               <1000000000>,
> +               <150000000>, <75000000>,
> +               <37500000>,
> +               <100000000>, <100000000>,
> +               <50000000>, <800000000>,
> +               <100000000>, <50000000>;
> +};
> +
> +&emmc_phy {
> +       status = "okay";
> +};
> +
> +ap_i2c_mic: &i2c1 {
> +       status = "okay";
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +
> +       headsetcodec: rt5514@57 {
> +               compatible = "realtek,rt5514";
> +               reg = <0x57>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&mic_int>;
> +
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
> +
> +               realtek,dmic-init-delay = <20>;
> +               wakeup-source;
> +       };
> +};
> +
> +ap_i2c_ts: &i2c3 {
> +       status = "okay";
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +};
> +
> +ap_i2c_tp: &i2c5 {
> +       status = "okay";
> +
> +       /*
> +        * Note strange pullup enable.  Apparently this avoids leakage but
> +        * still allows us to get nice 4.7K pullups for high speed i2c
> +        * transfers.  Basically we want the pullup on whenever the ap is
> +        * alive, so the "en" pin just gets set to output high.
> +        */
> +       pinctrl-0 = <&i2c5_xfer &ap_i2c_tp_pu_en>;
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +};
> +
> +ap_i2c_audio: &i2c8 {
> +       status = "okay";
> +
> +       clock-frequency = <400000>;
> +
> +       /* These are relatively safe rise/fall times */
> +       i2c-scl-falling-time-ns = <50>;
> +       i2c-scl-rising-time-ns = <300>;
> +
> +       codec: da7219@1a {
> +               compatible = "dlg,da7219";
> +               reg = <0x1a>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&headset_int_l>;
> +
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
> +
> +               VDD-supply = <&pp1800>;
> +               VDDMIC-supply = <&pp3300>;
> +               VDDIO-supply = <&pp1800>;
> +
> +               clocks = <&cru SCLK_I2S_8CH_OUT>;
> +               clock-names = "mclk";
> +
> +               dlg,micbias-lvl = <2600>;
> +               dlg,mic-amp-in-sel = "diff";
> +
> +               da7219_aad {
> +                       dlg,btn-cfg = <50>;
> +                       dlg,mic-det-thr = <500>;
> +                       dlg,jack-ins-deb = <20>;
> +                       dlg,jack-det-rate = "32ms_64ms";
> +                       dlg,jack-rem-deb = <1>;
> +
> +                       dlg,a-d-btn-thr = <0xa>;
> +                       dlg,d-b-btn-thr = <0x16>;
> +                       dlg,b-c-btn-thr = <0x21>;
> +                       dlg,c-mic-btn-thr = <0x3E>;
> +
> +                       dlg,btn-avg = <4>;
> +                       dlg,adc-1bit-rpt = <1>;
> +               };
> +       };
> +};
> +
> +&i2s0 {
> +       status = "okay";
> +};
> +
> +&i2s2 {
> +       status = "okay";
> +};
> +
> +&io_domains {
> +       status = "okay";
> +
> +       bt656-supply = <&pp1800_ap_io>;         /* APIO2_VDD;  2a 2b */
> +       audio-supply = <&pp1800_audio>;         /* APIO5_VDD;  3d 4a */
> +       sdmmc-supply = <&ppvar_sd_card_io>;     /* SDMMC0_VDD; 4b    */
> +       gpio1830-supply = <&pp3000_ap>;         /* APIO4_VDD;  4c 4d */
> +};
> +
> +&pcie0 {
> +       status = "okay";
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
> +       ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
> +
> +       vpcie3v3-supply = <&pp3300_wifi_bt>;
> +       vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
> +       vpcie0v9-supply = <&pp900_pcie>;
> +
> +       pci_rootport: pcie@0,0 {
> +               reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
> +               #address-cells = <3>;
> +               #size-cells = <2>;
> +               ranges;
> +
> +               mvl_wifi: wifi@0,0 {
> +                       compatible = "pci1b4b,2b42";
> +                       reg = <0x83010000 0x0 0x00000000 0x0 0x00100000
> +                              0x83010000 0x0 0x00100000 0x0 0x00100000>;
> +                       pinctrl-names = "default";
> +                       pinctrl-0 = <&wlan_host_wake_l>;
> +                       interrupt-parent = <&gpio0>;
> +                       interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +                       wakeup-source;
> +               };
> +       };
> +};
> +
> +&pcie_phy {
> +       status = "okay";
> +};
> +
> +
> +&pmu_io_domains {
> +       status = "okay";
> +
> +       pmu1830-supply = <&pp1800_pmu>;         /* PMUIO2_VDD */
> +};
> +
> +&pwm0 {
> +       status = "okay";
> +};
> +
> +&pwm1 {
> +       status = "okay";
> +};
> +
> +&pwm2 {
> +       status = "okay";
> +};
> +
> +&pwm3 {
> +       status = "okay";
> +};
> +
> +&sdhci {
> +       /*
> +        * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
> +        * same (or nearly the same) performance for all eMMC that are intended
> +        * to be used.
> +        */
> +       assigned-clock-rates = <150000000>;
> +
> +       bus-width = <8>;
> +       mmc-hs400-1_8v;
> +       mmc-hs400-enhanced-strobe;
> +       non-removable;
> +       status = "okay";
> +};
> +
> +&sdmmc {
> +       status = "okay";
> +
> +       /*
> +        * Note: configure "sdmmc_cd" as card detect even though it's actually
> +        * hooked to ground.  Because we specified "cd-gpios" below dw_mmc
> +        * should be ignoring card detect anyway.  Specifying the pin as
> +        * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
> +        * turned on that the system will still make sure the port is
> +        * configured as SDMMC and not JTAG.
> +        */
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
> +                    &sdmmc_bus4>;
> +
> +       bus-width = <4>;
> +       cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
> +       disable-wp;
> +
> +       cap-mmc-highspeed;
> +       cap-sd-highspeed;
> +       sd-uhs-sdr12;
> +       sd-uhs-sdr25;
> +       sd-uhs-sdr50;
> +       sd-uhs-sdr104;
> +
> +       vmmc-supply = <&pp3000_sd_slot>;
> +       vqmmc-supply = <&ppvar_sd_card_io>;
> +};
> +
> +&spi1 {
> +       status = "okay";
> +
> +       pinctrl-names = "default", "sleep";
> +       pinctrl-1 = <&spi1_sleep>;
> +
> +       spiflash@0 {
> +               compatible = "jedec,spi-nor";
> +
> +               /* May run faster once verified. */
> +               spi-max-frequency = <10000000>;
> +               reg = <0>;
> +       };
> +};
> +
> +&spi2 {
> +       status = "okay";
> +
> +       wacky_spi_audio: spi2@0 {
> +               compatible = "realtek,rt5514";
> +               reg = <0>;
> +
> +               /* May run faster once verified. */
> +               spi-max-frequency = <10000000>;
> +       };
> +};
> +
> +&spi5 {
> +       status = "okay";
> +
> +       cros_ec: ec@0 {
> +               compatible = "google,cros-ec-spi";
> +               reg = <0>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&ec_ap_int_l>;
> +
> +               interrupt-parent = <&gpio0>;
> +               interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +               spi-max-frequency = <3000000>;
> +
> +               i2c_tunnel: i2c-tunnel {
> +                       compatible = "google,cros-ec-i2c-tunnel";
> +                       google,remote-bus = <4>;
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +               };
> +
> +               cros_ec_pwm: ec-pwm {
> +                       compatible = "google,cros-ec-pwm";
> +                       #pwm-cells = <1>;
> +               };
> +       };
> +};
> +
> +&tsadc {
> +       status = "okay";
> +
> +       rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
> +       rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
> +};
> +
> +&u2phy0 {
> +       status = "okay";
> +};
> +
> +&u2phy1 {
> +       status = "okay";
> +};
> +
> +&u2phy0_host {
> +       status = "okay";
> +};
> +
> +&u2phy1_host {
> +       status = "okay";
> +};
> +
> +&u2phy0_otg {
> +       status = "okay";
> +};
> +
> +&u2phy1_otg {
> +       status = "okay";
> +};
> +
> +&uart2 {
> +       status = "okay";
> +};
> +
> +&usb_host0_ehci {
> +       status = "okay";
> +};
> +
> +&usb_host0_ohci {
> +       status = "okay";
> +};
> +
> +&usb_host1_ehci {
> +       status = "okay";
> +};
> +
> +&usb_host1_ohci {
> +       status = "okay";
> +};
> +
> +&usbdrd3_0 {
> +       status = "okay";
> +};
> +
> +&usbdrd_dwc3_0 {
> +       status = "okay";
> +       dr_mode = "host";
> +};
> +
> +&usbdrd3_1 {
> +       status = "okay";
> +};
> +
> +&usbdrd_dwc3_1 {
> +       status = "okay";
> +       dr_mode = "host";
> +};
> +
> +#include <arm/cros-ec-keyboard.dtsi>
> +#include <arm/cros-ec-sbs.dtsi>
> +
> +&pinctrl {
> +       /*
> +        * pinctrl settings for pins that have no real owners.
> +        *
> +        * At the moment settings are identical for S0 and S3, but if we later
> +        * need to configure things differently for S3 we'll adjust here.
> +        */
> +       pinctrl-names = "default";
> +       pinctrl-0 = <
> +               &ap_pwroff      /* AP will auto-assert this when in S3 */
> +               &clk_32k        /* This pin is always 32k on gru boards */
> +
> +               /*
> +                * We want this driven low ASAP; firmware should help us, but
> +                * we can help ourselves too.
> +                */
> +               &wlan_module_reset_l
> +       >;
> +
> +       pcfg_output_low: pcfg-output-low {
> +               output-low;
> +       };
> +
> +       pcfg_output_high: pcfg-output-high {
> +               output-high;
> +       };
> +
> +       pcfg_pull_none_8ma: pcfg-pull-none-8ma {
> +               bias-disable;
> +               drive-strength = <8>;
> +       };
> +
> +       cros-ec {
> +               ec_ap_int_l: ec-ap-int-l {
> +                       rockchip,pins = <RK_GPIO0 1 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +       };
> +
> +       discrete-regulators {
> +               pp1500_en: pp1500-en {
> +                       rockchip,pins = <RK_GPIO0 10 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               pp1800_audio_en: pp1800-audio-en {
> +                       rockchip,pins = <RK_GPIO0 2 RK_FUNC_GPIO
> +                                        &pcfg_pull_down>;
> +               };
> +
> +               pp3300_disp_en: pp3300-disp-en {
> +                       rockchip,pins = <RK_GPIO4 27 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               pp3000_en: pp3000-en {
> +                       rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               sd_io_pwr_en: sd-io-pwr-en {
> +                       rockchip,pins = <RK_GPIO2 2 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               sd_pwr_1800_sel: sd-pwr-1800-sel {
> +                       rockchip,pins = <RK_GPIO2 28 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               sd_slot_pwr_en: sd-slot-pwr-en {
> +                       rockchip,pins = <RK_GPIO4 29 RK_FUNC_GPIO
> +                                        &pcfg_pull_none>;
> +               };
> +
> +               wlan_module_pd_l: wlan-module-pd-l {
> +                       rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO
> +                                        &pcfg_pull_down>;
> +               };
> +       };
> +
> +       codec {
> +               /* Has external pullup */
> +               headset_int_l: headset-int-l {
> +                       rockchip,pins = <1 23 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +
> +               mic_int: mic-int {
> +                       rockchip,pins = <1 13 RK_FUNC_GPIO &pcfg_pull_down>;
> +               };
> +       };
> +
> +       max98357a {
> +               sdmode_en: sdmode-en {
> +                       rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_down>;
> +               };
> +       };
> +
> +       sdmmc {
> +               /*
> +                * We run sdmmc at max speed; bump up drive strength.
> +                * We also have external pulls, so disable the internal ones.
> +                */
> +               sdmmc_bus4: sdmmc-bus4 {
> +                       rockchip,pins =
> +                               <4 8 RK_FUNC_1 &pcfg_pull_none_8ma>,
> +                               <4 9 RK_FUNC_1 &pcfg_pull_none_8ma>,
> +                               <4 10 RK_FUNC_1 &pcfg_pull_none_8ma>,
> +                               <4 11 RK_FUNC_1 &pcfg_pull_none_8ma>;
> +               };
> +
> +               sdmmc_clk: sdmmc-clk {
> +                       rockchip,pins =
> +                               <4 12 RK_FUNC_1 &pcfg_pull_none_8ma>;
> +               };
> +
> +               sdmmc_cmd: sdmmc-cmd {
> +                       rockchip,pins =
> +                               <4 13 RK_FUNC_1 &pcfg_pull_none_8ma>;
> +               };
> +
> +               /*
> +                * In our case the official card detect is hooked to ground
> +                * to avoid getting access to JTAG just by sticking something
> +                * in the SD card slot (see the force_jtag bit in the TRM).
> +                *
> +                * We still configure it as card detect because it doesn't
> +                * hurt and dw_mmc will ignore it.  We make sure to disable
> +                * the pull though so we don't burn needless power.
> +                */
> +               sdmmc_cd: sdmcc-cd {
> +                       rockchip,pins =
> +                               <0 7 RK_FUNC_1 &pcfg_pull_none>;
> +               };
> +
> +               /* This is where we actually hook up CD; has external pull */
> +               sdmmc_cd_gpio: sdmmc-cd-gpio {
> +                       rockchip,pins = <4 24 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +
> +       spi1 {
> +               spi1_sleep: spi1-sleep {
> +                       /*
> +                        * Pull down SPI1 CLK/CS/RX/TX during suspend, to
> +                        * prevent leakage.
> +                        */
> +                       rockchip,pins = <1 9 RK_FUNC_GPIO &pcfg_pull_down>,
> +                                       <1 10 RK_FUNC_GPIO &pcfg_pull_down>,
> +                                       <1 7 RK_FUNC_GPIO &pcfg_pull_down>,
> +                                       <1 8 RK_FUNC_GPIO &pcfg_pull_down>;
> +               };
> +       };
> +
> +       trackpad {
> +               ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
> +                       rockchip,pins = <3 12 RK_FUNC_GPIO &pcfg_output_high>;
> +               };
> +
> +               trackpad_int_l: trackpad-int-l {
> +                       rockchip,pins = <1 4 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +       };
> +
> +       touchscreen {
> +               touch_int_l: touch-int-l {
> +                       rockchip,pins = <3 13 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +
> +               touch_reset_l: touch-reset-l {
> +                       rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +
> +       wifi {
> +               wifi_perst_l: wifi-perst-l {
> +                       rockchip,pins = <2 27 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +
> +               wlan_module_reset_l: wlan-module-reset-l {
> +                       /*
> +                        * We want this driven low ASAP (As {Soon,Strongly} As
> +                        * Possible), to avoid leakage through the powered-down
> +                        * WiFi.
> +                        */
> +                       rockchip,pins = <1 11 RK_FUNC_GPIO &pcfg_output_low>;
> +               };
> +
> +               bt_host_wake_l: bt-host-wake-l {
> +                       /* Kevin has an external pull up, but Gru does not */
> +                       rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +       };
> +
> +       backlight-enable {
> +               bl_en: bl-en {
> +                       rockchip,pins = <1 17 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +
> +       write-protect {
> +               ap_fw_wp: ap-fw-wp {
> +                       rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>;
> +               };
> +       };
> +
> +       pcie {
> +               pcie_clkreqn_cpm: pci-clkreqn-cpm {
> +                       /*
> +                        * Since our pcie doesn't support ClockPM(CPM), we want
> +                        * to hack this as gpio, so the EP could be able to
> +                        * de-assert it along and make ClockPM(CPM) work.
> +                        */
> +                       rockchip,pins = <2 26 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +};
> --
> 2.12.0.367.g23dc2f6d3c-goog
>

I don't have a kevin but I have a gru, so for the shared parts I can say

Tested-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux