On 03/11/2017 11:37 PM, Russell King - ARM Linux wrote:
On Sat, Mar 11, 2017 at 07:31:18PM -0800, Steve Longerbeam wrote:
On 03/11/2017 10:59 AM, Russell King - ARM Linux wrote:
On Sat, Mar 11, 2017 at 10:54:55AM -0800, Steve Longerbeam wrote:
On 03/11/2017 10:45 AM, Russell King - ARM Linux wrote:
I really don't think expecting the user to understand and configure
the pipeline is a sane way forward. Think about it - should the
user need to know that, because they have a bayer-only CSI data
source, that there is only one path possible, and if they try to
configure a different path, then things will just error out?
For the case of imx219 connected to iMX6, it really is as simple as
"there is only one possible path" and all the complexity of the media
interfaces/subdevs is completely unnecessary. Every other block in
the graph is just noise.
The fact is that these dot graphs show a complex picture, but reality
is somewhat different - there's only relatively few paths available
depending on the connected source and the rest of the paths are
completely useless.
I totally disagree there. Raw bayer requires passthrough yes, but for
all other media bus formats on a mipi csi-2 bus, and all other media
bus formats on 8-bit parallel buses, the conersion pipelines can be
used for scaling, CSC, rotation, and motion-compensated de-interlacing.
... which only makes sense _if_ your source can produce those formats.
We don't actually disagree on that.
...and there are lots of those sources! You should try getting out of
your imx219 shell some time, and have a look around! :)
If you think that, you are insulting me. I've been thinking about this
from the "big picture" point of view. If you think I'm only thinking
about this from only the bayer point of view, you're wrong.
No insult there, you have my utmost respect Russel. Me gives you the
Ali-G "respec!" :)
It was just a light-hearted attempt at suggesting you might be too
entangled with the imx219 (or short on hardware access, which I can
certainly understand).
Given what Mauro has said, I'm convinced that the media controller stuff
is a complete failure for usability, and adding further drivers using it
is a mistake.
I do agree with you that MC places a lot of burden on the user to
attain a lot of knowledge of the system's architecture. That's really
why I included that control inheritance patch, to ease the burden
somewhat.
On the other hand, I also think this just requires that MC drivers have
very good user documentation.
And my other point is, I think most people who have a need to work with
the media framework on a particular platform will likely already be
quite familiar with that platform.
I counter your accusation by saying that you are actually so focused on
the media controller way of doing things that you can't see the bigger
picture here.
Yeah I've been too mired in the details of this driver.
So, tell me how the user can possibly use iMX6 video capture without
resorting to opening up a terminal and using media-ctl to manually
configure the pipeline. How is the user going to control the source
device without using media-ctl to find the subdev node, and then using
v4l2-ctl on it. How is the user supposed to know which /dev/video*
node they should be opening with their capture application?
The media graph for imx6 is fairly self-explanatory in my opinion.
Yes that graph has to be generated, but just with a simple 'media-ctl
--print-dot', I don't see how that is difficult for the user.
The graph makes it quite clear which subdev node belongs to which
entity.
As for which /dev/videoX node to use, I hope I made it fairly clear
in the user doc what functions each node performs. But I will review
the doc again and make sure it's been made explicitly clear.
If you can actually respond to the points that I've been raising about
end user usability, then we can have a discussion.
Right, I haven't added my input to the middle-ware discussions (libv4l,
v4lconvert, and the auto-pipeline-configuration library work). I can
only say at this point that v4lconvert does indeed sound broken w.r.t
bayer formats from your description. But it also sounds like an isolated
problem and it just needs a patch to allow passing bayer through without
software conversion.
I wish I had the IMX219 to help you debug these bayer issues. I don't
have any bayer sources.
In summary, I do like the media framework, it's a good abstraction of
hardware pipelines. It does require a lot of system level knowledge to
configure, but as I said that is a matter of good documentation.
Steve
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
