On Sat, Mar 4, 2017 at 5:58 AM, Sebastian Reichel <sre@xxxxxxxxxx> wrote:
> This adds a driver for the Nokia H4+ protocol, which is used
> at least on the Nokia N9, N900 & N950.
>
> Signed-off-by: Sebastian Reichel <sre@xxxxxxxxxx>
> ---
> .../devicetree/bindings/net/nokia-bluetooth.txt | 51 ++
This should be separate and before the dts files.
> drivers/bluetooth/Kconfig | 12 +
> drivers/bluetooth/Makefile | 2 +
> drivers/bluetooth/hci_nokia.c | 839 +++++++++++++++++++++
> 4 files changed, 904 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> create mode 100644 drivers/bluetooth/hci_nokia.c
>
> diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> new file mode 100644
> index 000000000000..6c80a92f31e2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt
> @@ -0,0 +1,51 @@
> +Nokia Bluetooth Chips
> +---------------------
> +
> +Nokia phones often come with UART connected bluetooth chips from different
> +vendors and modified device API. Those devices speak a protocol named H4+
> +by Nokia, which is similar to the H4 protocol from the Bluetooth standard.
> +In addition to the H4 protocol it specifies two more UART status lines for
> +wakeup of UART transceivers to improve power management and a few new packet
> +types used to negotiate uart speed.
> +
> +Required properties:
> +
> + - compatible: should be one of the following:
> + * "nokia,brcm,bcm2048"
> + * "nokia,ti,wl1271-bluetooth"
Drop the chip vendors' prefix here. I don't really want to start a
pattern of 2 vendor prefixes.
> + - reset-gpios: GPIO specifier, used to reset the BT module
Need to state active state.
> + - bluetooth-wakeup-gpios: GPIO specifier, used to wakeup the BT module
> + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor
I think most BCM devices have these. These apply to the TI device too?
If not, then add brcm prefix.
Also need to specify the active state.
> + - clock-names: should be "sysclk"
> + - clocks: should contain a clock specifier for every name in clock-names
> +
> +Optional properties:
> +
> + - None
> +
> +Example:
> +
> +/ {
> + /* controlled (enabled/disabled) directly by BT module */
> + bluetooth_clk: vctcxo {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <38400000>;
> + };
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins>;
> +
> + bluetooth {
> + compatible = "nokia,ti,wl1271-bluetooth";
> +
> + reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; /* gpio26 */
> + host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */
> + bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* gpio37 */
> +
> + clocks = <&bluetooth_clk>;
> + clock-names = "sysclk";
> + };
> +};
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
