On Tue, Feb 14, 2017 at 8:31 AM, Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> wrote:
> On Tue, 2017-02-14 at 07:46 -0800, Andrey Smirnov wrote:
> [...]
>> >> +enum imx7_src_registers {
>> >> + SRC_PCIEPHY_RCR = 0x002c,
>> >> + SRC_PCIEPHY_RCR_PCIEPHY_G_RST = BIT(1),
>> >
>> > What about the others resets? There's at least HSICPHY, MIPIPHY and
>> > USBOPHY registers before the PCIEPHY register.
>>
>> I don't really have any code using anything but PCI reset related
>> functionality, so I can't test any of the resets you mention. In light
>> of that I didn't want to add any of the definitions that are not going
>> to be used anywhere in the code.
>
> Since the device tree bindings are supposed to be descriptive of the
> hardware, not of the development history of the linux driver, I'd like
> the reset controls to be in a sensible order. From a quick scan of the
> chapter in the reference manual, this is the complete list of resets:
>
> A7_CORE_POR_RESET0
> A7_CORE_POR_RESET1
> A7_CORE_RESET0
> A7_CORE_RESET1
> A7_DBG_RESET0
> A7_DBG_RESET1
> A7_ETM_RESET0
> A7_ETM_RESET1
> A7_SOC_DBG_RESET
> A7_L2RESET
> SW_M4C_RST
> SW_M4P_RST
> EIM_RST
> HSICPHY_PORT_RST
> HSIC_PHY_POR (or Reserved, the manual is conflicted about this)
> USBPHY1_POR
> USBPHY1_PORT_RST
> USBPHY2_POR
> USBPHY2_PORT_RST
> MIPI_PHY_MRST
> MIPI_PHY_SRST
> PCIEPHY_G_RST
> PCIEPHY_BTN
> PCIEPHY_PERST
> PCIE_CTRL_APPS_RST/EN
>
> Arguably, the A7 resets should not be handled by the peripheral reset
> controller, but at least for the others I see no reason not to leave
> space for them in the index table.
If for some bizarre reason one was to run Linux on M4 and use A7 as
applications processor, resetting A7 might be useful. But that's a
very unlikely use-case.
> In fact, since unused reset controls
> don't use space, why not number them all?
IMHO because it is unused code and because those numbers constitute an
interface which once set will be hard to change if need be.
But that's not that important and I don't feel particularly strong
about that point, so I'll add those sources in v3.
Do you insist that I split what I call IMX7_RESET_PCIEPHY into
PCIEPHY_G_RST and PCIEPHY_BTN or can I keep it as a single logical
reset?
>
>> >
>> >> + SRC_PCIEPHY_RCR_PCIEPHY_BTN = BIT(2),
>> >> + SRC_PCIEPHY_RCR_PCIE_CTRL_APPS_EN = BIT(6),
>> >
>> > Are those really resets? At least the PCIE_CTRL_APPS_EN has a bit called
>> > PCIE_CTRL_APPS_RST right next to it, so this warrants some explanation.
>>
>> Public documentation for that aspect of i.MX7 is nonexistent and,
>> unfortunately, that is my only source of information. Given that, I
>> can't really tell you what the difference between PCIE_CTRL_APPS_EN
>> and PCIE_CTRL_APPS_RST besides that the former is what downstream PCIe
>> driver uses to inhibit LTSSM and the latter is not referenced or used
>> by any code (as far as I am aware).
>
> Ok. That's unfortunate, but nothing we can do about that.
> After discussing with Lucas, I've come to the belief that APPS_EN stops
> the LTSSM, whereas APPS_RST might reset it into the initial state. Since
> the latter doesn't exist at all on i.MX6, and we can obviously live
> without it, I'm fine with just calling the enable bit an active low
> reset to hold it in place. It doesn't fit perfectly, but probably better
> to put it here than building i.MX7 specific fabric code around the DW
> PCIe driver.
>
> [...]
>> >> + regmap_update_bits(imx7src->regmap,
>> >> + SRC_PCIEPHY_RCR,
>> >> + SRC_PCIEPHY_RCR_PCIEPHY_BTN,
>> >> + SRC_PCIEPHY_RCR_PCIEPHY_BTN);
>> >
>> > What is the PCIE PHY button, and why does it have to be set with the
>> > reset bit?
>>
>> I am sorry, but just as above, I wouldn't be able to enlighten you any
>> more about the subject. I have no knowledge about the details of G_RST
>> and BTN signal (or even if BTN stands for "button") behavior beyond
>> the fact that that is how downstream driver performs PCIEPHY reset.
>
> The SRC_PCIEPHY_RCR register documentation in the i.MX 7Dual
> Applications Processor Reference Manual v0.1 describes this bit as "PCIE
> PHY button".
Oh, yes, that's right. Missed that the datasheet spells "button" explicitly.
>
> [...]
>> >> +#define IMX7_RESET_PCIE_CTRL_APPS 0
>> >> +#define IMX7_RESET_PCIEPHY 1
>> >
>> > It would expect these to be numbered in the order they appear in the
>> > register map, not starting from the end. Could you add all available
>> > peripheral resets to this list, in the correct order?
>>
>> The numbering is just a consequence of me adding only resets I could
>> exercise with my code and numbering then starting from zero. I also
>> was hesitant adding more sources since it seemed to me that some of
>> less trivial registers in that IP block might be best represented as a
>> single reset source doing something more sophisticated that just
>> setting a bit under the hood.
>
> Any in particular?
USBPHY1/2 and maybe MIPI resets? But that's no more than a gut feeling.
Thanks,
Andrey Smirnov
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
