On Wed, Feb 8, 2017 at 9:40 AM, <eajames@xxxxxxxxxxxxxxxxxx> wrote:
> From: "Edward A. James" <eajames@xxxxxxxxxx>
>
> Add code to tie the hwmon sysfs code and the POWER8 OCC code together, as
> well as probe the entire driver from the I2C bus. I2C is the communication
> method between the BMC and the P8 OCC.
>
> Signed-off-by: Edward A. James <eajames@xxxxxxxxxx>
> Signed-off-by: Andrew Jeffery <andrew@xxxxxxxx>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> Documentation/devicetree/bindings/hwmon/occ.txt | 13 +++
> drivers/hwmon/occ/Kconfig | 14 ++++
> drivers/hwmon/occ/Makefile | 1 +
> drivers/hwmon/occ/p8_occ_i2c.c | 104 ++++++++++++++++++++++++
For consistency, how about we call this occ_p8_i2c.c? The other files
have the machine name second.
> 4 files changed, 132 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/hwmon/occ.txt
> create mode 100644 drivers/hwmon/occ/p8_occ_i2c.c
>
> diff --git a/drivers/hwmon/occ/Kconfig b/drivers/hwmon/occ/Kconfig
> index cdb64a7..3a5188f 100644
> --- a/drivers/hwmon/occ/Kconfig
> +++ b/drivers/hwmon/occ/Kconfig
> @@ -13,3 +13,17 @@ menuconfig SENSORS_PPC_OCC
>
> This driver can also be built as a module. If so, the module
> will be called occ.
> +
> +if SENSORS_PPC_OCC
> +
> +config SENSORS_PPC_OCC_P8_I2C
> + tristate "POWER8 OCC hwmon support"
> + depends on I2C
> + help
> + Provide a hwmon sysfs interface for the POWER8 On-Chip Controller,
> + exposing temperature, frequency and power measurements.
> +
> + This driver can also be built as a module. If so, the module will be
> + called p8-occ-i2c.
Mention that this driver is for the BMC (or just "service processor"),
and is not useful in the Power8 kernel.
I'm trying to think of a better prefix than PPC. PPC means much more
than Power8 and Power9, which is what we mean. It's also confusing as
we don't run this on any PowerPC machine - it's for an ARM chip.
> +
> +int p8_i2c_getscom(void *bus, u32 address, u64 *data)
> +{
> + /* P8 i2c slave requires address to be shifted by 1 */
> + address = address << 1;
I think these are scom addresses? Please indicate that so we don't get
them confused with i2c.
Or are they scom operations?
> +
> + return occ_i2c_getscom(bus, address, data);
> +}
> +
> +int p8_i2c_putscom(void *bus, u32 address, u32 data0, u32 data1)
The functions can be static.
> +{
> + /* P8 i2c slave requires address to be shifted by 1 */
> + address = address << 1;
> +
> + return occ_i2c_putscom(bus, address, data0, data1);
> +}
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
