On Tue, Jan 24, 2017 at 07:26:41PM +0100, Marek Vasut wrote:
> Add DT bindings for the Renesas RCar GyroADC block. This block is
> a simple 4/8-channel ADC which samples 12/15/24 bits of data every
> cycle from all channels.
>
> Signed-off-by: Marek Vasut <marek.vasut@xxxxxxxxx>
> Cc: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> Cc: Simon Horman <horms+renesas@xxxxxxxxxxxx>
> Cc: Jonathan Cameron <jic23@xxxxxxxxxx>
> Cc: linux-renesas-soc@xxxxxxxxxxxxxxx
> Cc: Wolfram Sang <wsa@xxxxxxxxxxxxx>
> Cc: Rob Herring <robh@xxxxxxxxxx>
> Cc: devicetree@xxxxxxxxxxxxxxx
> ---
> V8: - Sync the version with the 2/2 driver patch
> - Drop status prop from example
> - Add GyroADC block description
> - Enumerate the compatible string values
> - Make subnodes mandatory
> ---
> .../bindings/iio/adc/renesas,gyroadc.txt | 99 ++++++++++++++++++++++
> 1 file changed, 99 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt
> new file mode 100644
> index 000000000000..7f9b3bd120a9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt
> @@ -0,0 +1,99 @@
> +* Renesas RCar GyroADC device driver
> +
> +The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
> +which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
> +are sampled by the GyroADC block in a round-robin fashion and the result
> +presented in the GyroADC registers.
> +
> +Required properties:
> +- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc".
> + The <soc-specific> should be one of:
> + renesas,r8a7791-gyroadc - for the GyroADC block present
> + in r8a7791 SoC
> + renesas,r8a7792-gyroadc - for the GyroADC with interrupt
> + block present in r8a7792 SoC
> +- reg: Address and length of the register set for the device
> +- clocks: References to all the clocks specified in the clock-names
> + property as specified in
> + Documentation/devicetree/bindings/clock/clock-bindings.txt.
> +- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block
> + clock, the "if" is the interface clock.
> +- power-domains: Must contain a reference to the PM domain, if available.
> +- #address-cells: Should be <1> (setting for the subnodes) for all ADCs
> + except for "fujitsu,mb88101a". Should be <0> (setting for
> + only subnode) for "fujitsu,mb88101a".
> +- #size-cells: Should be <0> (setting for the subnodes)
> +
> +Sub-nodes:
> +You must define subnode(s) which select the connected ADC type and reference
> +voltage for the GyroADC channels.
> +
> +Required properties for subnodes:
> +- compatible: Should be either of:
> + "fujitsu,mb88101a"
> + - Fujitsu MB88101A compatible mode,
> + 12bit sampling, up to 4 channels can be sampled in
> + round-robin fashion. One Fujitsu chip supplies four
> + GyroADC channels with data as it contains four ADCs
> + on the chip and thus for 4-channel operation, single
> + MB88101A is required. The Cx chipselect lines of the
> + MB88101A connect directly to two CHS lines of the
> + GyroADC, no demuxer is required. The data out line
> + of each MB88101A connects to a shared input pin of
> + the GyroADC.
> + "ti,adcs7476" or "ti,adc121" or "adi,ad7476"
> + - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode,
> + 15bit sampling, up to 8 channels can be sampled in
> + round-robin fashion. One TI/ADI chip supplies single
> + ADC channel with data, thus for 8-channel operation,
> + 8 chips are required. A 3:8 chipselect demuxer is
> + required to connect the nCS line of the TI/ADI chips
> + to the GyroADC, while MISO line of each TI/ADI ADC
> + connects to a shared input pin of the GyroADC.
> + "maxim,max1162" or "maxim,max11100"
> + - Maxim MAX1162 / Maxim MAX11100 compatible mode,
> + 16bit sampling, up to 8 channels can be sampled in
> + round-robin fashion. One Maxim chip supplies single
> + ADC channel with data, thus for 8-channel operation,
> + 8 chips are required. A 3:8 chipselect demuxer is
> + required to connect the nCS line of the MAX chips
> + to the GyroADC, while MISO line of each Maxim ADC
> + connects to a shared input pin of the GyroADC.
> +- reg: Should be the number of the analog input. Should be present
> + for all ADCs except "fujitsu,mb88101a".
> +- vref-supply: Reference to the channel reference voltage regulator.
> +
> +Example:
> + vref_max1162: regulator-vref-max1162 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "MAX1162 Vref";
> + regulator-min-microvolt = <4096000>;
> + regulator-max-microvolt = <4096000>;
> + };
> +
> + &adc {
This wouldn't actually work unless you include something that defines
'&adc'. Make this adc@e6e54000.
With that,
Acked-by: Rob Herring <robh@xxxxxxxxxx>
> + compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
> + reg = <0 0xe6e54000 0 64>;
> + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>;
> + clock-names = "fck", "if";
> + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
> +
> + pinctrl-0 = <&adc_pins>;
> + pinctrl-names = "default";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + adc@0 {
> + reg = <0>;
> + compatible = "maxim,max1162";
> + vref-supply = <&vref_max1162>;
> + };
> +
> + adc@1 {
> + reg = <1>;
> + compatible = "maxim,max1162";
> + vref-supply = <&vref_max1162>;
> + };
> + };
> --
> 2.11.0
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
