On Tue, Jan 24, 2017 at 12:36 AM, Frank Rowand <frowand.list@xxxxxxxxx> wrote:
> Hi Stephen,
>
> Sorry I did not get to v1 and v2 in a timely manner.
>
>
> On 01/23/17 12:48, Stephen Boyd wrote:
>> Platforms like 96boards have a standardized connector/expansion
>> slot that exposes signals like GPIOs to expansion boards in an
>> SoC agnostic way. We'd like the DT overlays for the expansion
>> boards to be written once without knowledge of the SoC on the
>> other side of the connector. This avoids the unscalable
>> combinatorial explosion of a different DT overlay for each
>> expansion board and SoC pair.
>>
>> We need a way to describe the GPIOs routed through the connector
>> in an SoC agnostic way. Let's introduce nexus property parsing
>> into the OF core to do this. This is largely based on the
>> interrupt nexus support we already have. This allows us to remap
>> a phandle list in a consumer node (e.g. reset-gpios) through a
>> connector in a generic way (e.g. via gpio-map). Do this in a
>> generic routine so that we can remap any sort of variable length
>> phandle list.
>>
>> Taking GPIOs as an example, the connector would be a GPIO nexus,
>> supporting the remapping of a GPIO specifier space to multiple
>> GPIO providers on the SoC. DT would look as shown below, where
>> 'soc_gpio1' and 'soc_gpio2' are inside the SoC, 'connector' is an
>> expansion port where boards can be plugged in, and
>> 'expansion_device' is a device on the expansion board.
>>
>> soc {
>> soc_gpio1: gpio-controller1 {
>> #gpio-cells = <2>;
>> };
>>
>> soc_gpio2: gpio-controller2 {
>> #gpio-cells = <2>;
>> };
>> };
>>
>> connector: connector {
>> #gpio-cells = <2>;
>> gpio-map = <0 0 &soc_gpio1 1 0>,
>> <1 0 &soc_gpio2 4 0>,
>> <2 0 &soc_gpio1 3 0>,
>> <3 0 &soc_gpio2 2 0>;
>> gpio-map-mask = <0xf 0x0>;
>> gpio-map-pass-thru = <0x0 0x1>
>> };
>>
>> expansion_device {
>> reset-gpios = <&connector 2 GPIO_ACTIVE_LOW>;
>> };
>
> The how to architect connectors and plugs threads fell asleep before
> coming to a resolution. We need to revive that discussion.
>
> One of the concepts of the plug and connector architecture is that
> a main board may contain multiple connectors of the same type (or
> different types, but the same type is sufficient for this discussion).
>
> The node describing the card that plugs into one of the connectors
> does not know the phandle of the connector it is going to be
> connected to. Some other mechanism is provided to allow a card
> to be plugged into any of the available connectors. If there are
> two identical cards plugged into two connectors, then both cards
> have the same exact device tree node. But some mechanism will
> exist to resolve (or "link") the two card nodes to the different
> connector nodes.
>
> As a result of this, in the above example the reset-gpios property
> in the node 'expansion_device' can not contain '&connector'. The
> concept of &connector belongs to the entire expansion_device node,
> not to individual properties within the node.
I think this is easily solved with a connector having 2 halves and
that we need to search parents for *-map properties. Inheriting from
parents is a common pattern in DT though perhaps not walking the
parents of a phandle. So we'd have something like this:
base-connector-1 {
gpio-map = ...
connector {
child {
some-gpios = <&connector 1>;
};
};
};
base-connector-2 {
gpio-map = ...
connector {
child {
some-gpios = <&connector 1>;
};
};
};
Now, how we resolve that /connector from an overlay targets
/base-connector-1 and /base-connector-2 is an orthogonal issue and one
that's going to be connector specific (at least for probe-able
connectors).
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
