This series adds an FPGA manager for Altera cyclone FPGAs that can program them using an spi port and a couple of gpios, using Alteras passive serial protocol. Changes from v7: Add Rob Herrings Ack on the bindings change (Thanks!) Change const u8* to const char * to make sparse happy Changes from v6: - moved bitrev8x4() out (I'll submit it in a separate patch set) - Changed the dts format to match what is already done in barebox (see https://git.pengutronix.de/cgit/barebox/tree/Documentation/devicetree/bindings/firmware/altr,passive-serial.txt) - Changed error message from "Status pin should be low" to "Status pin failed to show a reset" for better clarity - Fixed any whitespace problems that had crept in. Changes from v5: - Rebased on next-20161214xi - Corrected for FPGA Mgr API change in write_init() and write_complete() - Better describe the device cyclone-ps-spi runs on in the file header. - Split the bitrev8x4 patch into generic and arch specific patches... - Added AARCH64 and MIPS implementations of bitrev8x4()... they all have to have an implementation for it to compile cleanly across platforms - Added the changes to imx6q-evi.dts to the patch set. Changes from v4: - Added the needed return statement to __arch_bitrev8x4() - Added Rob Herrings ACK for and fix a typo in the commit log of patch 2 Changes from v3: - Fixed up the state() function to return the state of the status pin reqested by Alan Tull - Switched the pin to ACTIVE_LOW and coresponding logic level, and updated the corresponding documentation. Thanks Rob Herring for pointing out my mistake. - Per Rob Herring, switched from "gpio" to "gpios" in dts Changes from v2: - Merged patch 3 and 4 as suggested in review by Moritz Fischer - Changed FPGA_MIN_DELAY from 250 to 50 ms is the time advertized by Altera. This now works, as we don't assume it is done Changes from v1: - Changed the name from cyclone-spi-fpga-mgr to cyclone-ps-spi-fpga-mgr This name change was requested by Alan Tull, to be specific about which programming method is being employed on the fpga. - Changed the name of the reset-gpio to config-gpio to closer match the way the pins are described in the Altera manual - Moved MODULE_LICENCE, _AUTHOR, and _DESCRIPTION to the bottom - Added a bitrev8x4() function to the bitrev headers and implemented ARM const, runtime, and ARM specific faster versions (This may end up needing to be a standalone patch) - Moved the bitswapping into cyclonespi_write(), as requested. This falls short of my desired generic lsb first spi support, but is a step in that direction. - Fixed whitespace problems introduced during refactoring - Replaced magic number for initial delay with a descriptive macro - Poll the fpga to see when it is ready rather than a fixed 1 ms sleep Joshua Clayton (3): doc: dt: add cyclone-ps-spi binding document fpga manager: Add cyclone-ps-spi driver for Altera FPGAs ARM: dts: imx6q-evi: support cyclone-ps-spi .../bindings/fpga/altera-passive-serial.txt | 25 +++ arch/arm/boot/dts/imx6q-evi.dts | 16 ++ drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/cyclone-ps-spi.c | 185 +++++++++++++++++++++ 5 files changed, 234 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/altera-passive-serial.txt create mode 100644 drivers/fpga/cyclone-ps-spi.c -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
