While at tweak some more settings for the default product:
- enable lradc
- adjust USB dr mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
Signed-off-by: Michael Heimpold <mhei@xxxxxxxxxxx>
---
arch/arm/boot/dts/imx28-duckbill.dts | 81 +++++++++++++++++++++++++-----------
1 file changed, 56 insertions(+), 25 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
index ce1a7ef..3e4385d 100644
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ b/arch/arm/boot/dts/imx28-duckbill.dts
@@ -1,5 +1,6 @@
/*
- * Copyright (C) 2013 Michael Heimpold <mhei@xxxxxxxxxxx>
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@xxxxxxxxxxx>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@xxxxxxxx>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
@@ -10,6 +11,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
@@ -32,6 +34,13 @@
status = "okay";
};
+ ssp2: ssp@80014000 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+ };
+
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
@@ -39,14 +48,24 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
+ MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ mac0_phy_reset_pin: mac0-phy-reset@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- led_pins_a: led_gpio@0 {
+ led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
@@ -60,6 +79,22 @@
};
apbx@80040000 {
+ lradc@80050000 {
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+ };
+
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
@@ -75,47 +110,43 @@
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
+ dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
+ pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <®_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
+ phy-reset-duration = <25>;
status = "okay";
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_3p3v: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins_a>;
+ pinctrl-0 = <&led_pins>;
- status {
- label = "duckbill:green:status";
- gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
- };
-
- failure {
+ status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ status-green {
+ label = "duckbill:green:status";
+ gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
};
};
};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
