Hi Martin,
Quick process point. Personally I'd much prefer it if new versions
fo the patch are not posted as replies to earlier versions. It gets
awfully deep and hard to follow very quickly!
Thanks,
Jonathan
On 19/01/17 14:58, Martin Blumenstingl wrote:
> This series add support for the SAR ADC on Amlogic Meson GXBB, GXL and
> GXM SoCs.
> The hardware on GXBB provides 10-bit ADC results, while GXL and GXM are
> providing 12-bit results. Support for older SoCs (Meson8b and Meson8)
> can be added with little effort, most of which is testing I guess (I
> don't have any pre-GXBB hardware so I can't say).
>
> A new set of clocks had to be added to the GXBB clock controller (used
> by the GXBB/GXL/GXM SoCs) which are required to get the ADC working.
>
> The ADC itself can sample multiple channels at the same time and allows
> capturing multiple samples (which can be used for filtering/averaging).
> The ADC results are stored inside a FIFO register. More details on what
> the driver supports (or doesn't) can be found in the description of
> patch #3.
>
> The code is based on the public S805 (Meson8b) and S905 (GXBB)
> datasheets, as well as by reading (various versions of) the vendor
> driver and by inspecting the registers on the vendor kernels of my
> testing-hardware.
>
> Typical use-cases for the ADC on the Meson GX SoCs are:
> - adc-keys ("ADC attached resistor ladder buttons")
> - SoC temperature measurement (not supported by this driver yet as
> the system firmware does this already and provides the values via the
> SCPI protocol)
> - "version-strapping" (different resistor values are used to indicate
> the board-revision)
> - and of course typical ADC measurements
>
> Thanks to Heiner Kallweit, Jonathan Cameron, Lars-Peter Clausen and
> Peter Meerwald-Stadler for reviewing this series and providing valuable
> input!
>
> Changes since v2 (all changes are for patch #3, except where noted):
> - fixed another typo in the interrupt (patch #4, thanks again Heiner
> Kallweit)
> - change namespace of all register #defines to MESON_SAR_ADC (I
> intentionally decided to keep SAR_ADC in it because that's the way
> registers are named in the datasheet, thus making it easy to match the
> registers without having to look up the offset all the time)
> - added additional parenthesis around MACRO parameters for extra safety
> - removed unused definition for SAR_ADC_REG3_ADC_CLK_DIV_MASK (as we
> already have SAR_ADC_REG3_ADC_CLK_DIV_SHIFT and
> SAR_ADC_REG3_ADC_CLK_DIV_WIDTH which are used instead)
> - change value of "indexed" from "true" to "1"
> - remove type parameter from MESON_SAR_ADC_CHAN macro as all channels are
> currently IIO_VOLTAGE channels
> - fixed another multi-line comment style violation
> - added timeout to meson_saradc_lock() (unlikely to be triggered, but
> better safe then sorry - which would mean that we'd be keeping one core
> busy infinitely)
> - fixed meson_saradc_remove() call order (first unregister the iio_dev,
> then disable the hardware instead of the other way around)
> - use "consistent prefixing", which means that all #defines now use
> MESON_SAR_ADC_ as prefix, while all enums, static global variables,
> structs and functions use meson_sar_adc_ as prefix
> - rebased .dts and clk patches to apply to khilman's latest v4.11/dt64
> (a minor conflict had to be resolved in the clk patch due to
> "clk: meson-gxbb: Export HDMI clocks")
> - added Tested-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx> to all
> patches (thanks for testing!)
>
> Changes since v1 (all changes are for patch #3, except where noted):
> - fix IRQ number in meson-gx.dtsi (thanks to Heiner Kallweit for
> providing the correct value), affects patch #4
> - move the most used members of meson_saradc_priv to the beginning
> - remove unused struct member "completion" from meson_saradc_priv
> - use devm_kasprintf() instead of snprintf() + devm_kstrdup()
> - initialize indio_dev->dev.parent earlier in meson_saradc_probe()
> - moved meson_saradc_clear_fifo() logic to a separate function
> - add comment why a do ... while loop is required in
> meson_saradc_wait_busy_clear()
> - remove SAR_ADC_NUM_CHANNELS and SAR_ADC_VALUE_MASK macros (each of them
> was only used once and it's an unneeded level of abstraction)
> - fixed multiline comment syntax violations
> - dropped unneeded log messages during initialization
> - set iio_dev name to "meson-gxbb-saradc" or "meson-gxl-saradc"
> - use "indio_dev->dev.parent" in all kernel log calls (dev_warn/err/etc)
> to make it show the OF node name (instead of the iio device name)
> - introduce struct meson_saradc_data to hold platform-specific
> information (such as resolution in bits and the iio_dev name)
>
>
> Martin Blumenstingl (4):
> Documentation: dt-bindings: add the Amlogic Meson SAR ADC
> documentation
> clk: gxbb: add the SAR ADC clocks and expose them
> iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs
> ARM64: dts: meson: meson-gx: add the SAR ADC
>
> .../bindings/iio/adc/amlogic,meson-saradc.txt | 31 +
> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 8 +
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 10 +
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 10 +
> drivers/clk/meson/gxbb.c | 48 ++
> drivers/clk/meson/gxbb.h | 9 +-
> drivers/iio/adc/Kconfig | 12 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/meson_saradc.c | 916 +++++++++++++++++++++
> include/dt-bindings/clock/gxbb-clkc.h | 4 +
> 10 files changed, 1046 insertions(+), 3 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt
> create mode 100644 drivers/iio/adc/meson_saradc.c
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
