On Wed, 18 Jan 2017, Benjamin Gaignard wrote: > version 8: > - rebase on v4.10-rc4 > - fix comments done by Thierry on PWM > - reword "reg" parameter description > - change kernel kernel in IIO ABI documentation > > version 7: > - rebase on v4.10-rc2 > - remove iio_device code from driver and keep only the trigger part > > version 6: > - rename stm32-gptimer in stm32-timers. > - change "st,stm32-gptimer" compatible to "st,stm32-timers". > - modify "st,breakinput" parameter in pwm part. > - split DT patch in 2 > > version 5: > - fix comments done on version 4 > - rebased on kernel 4.9-rc8 > - change nodes names and re-order then by addresses > > version 4: > - fix comments done on version 3 > - don't use interrupts anymore in IIO timer > - detect hardware capabilities at probe time to simplify binding > > version 3: > - no change on mfd and pwm divers patches > - add cross reference between bindings > - change compatible to "st,stm32-timer-trigger" > - fix attributes access rights > - use string instead of int for master_mode and slave_mode > - document device attributes in sysfs-bus-iio-timer-stm32 > - update DT with the new compatible > > version 2: > - keep only one compatible per driver > - use DT parameters to describe hardware block configuration: > - pwm channels, complementary output, counter size, break input > - triggers accepted and create by IIO timers > - change DT to limite use of reference to the node > - interrupt is now in IIO timer driver > - rename stm32-mfd-timer to stm32-timers (for general purpose timer) > > The following patches enable PWM and IIO Timer features for STM32 platforms. > > Those two features are mixed into the registers of the same hardware block > (named general purpose timer) which lead to introduce a multifunctions driver > on the top of them to be able to share the registers. > > In STM32f4 14 instances of timer hardware block exist, even if they all have > the same register mapping they could have a different number of pwm channels > and/or different triggers capabilities. We use various parameters in DT to > describe the differences between hardware blocks > > The MFD (stm32-timers.c) takes care of clock and register mapping > by using regmap. stm32_timers structure is provided to its sub-node to > share those information. > > PWM driver is implemented into pwm-stm32.c. Depending of the instance we may > have up to 4 channels, sometime with complementary outputs or 32 bits counter > instead of 16 bits. Some hardware blocks may also have a break input function > which allows to stop pwm depending of a level, defined in devicetree, on an > external pin. > > IIO timer driver (stm32-timer-trigger.c and stm32-timer-trigger.h) define a list > of hardware triggers usable by hardware blocks like ADC, DAC or other timers. > > The matrix of possible connections between blocks is quite complex so we use > trigger names and is_stm32_iio_timer_trigger() function to be sure that > triggers are valid and configure the IPs. > > At run time IIO timer hardware blocks can configure (through "master_mode" > IIO device attribute) which internal signal (counter enable, reset, > comparison block, etc...) is used to generate the trigger. > > Benjamin Gaignard (8): > MFD: add bindings for STM32 Timers driver > MFD: add STM32 Timers driver > PWM: add pwm-stm32 DT bindings > PWM: add PWM driver for STM32 plaftorm > IIO: add bindings for STM32 timer trigger driver > IIO: add STM32 timer trigger driver > ARM: dts: stm32: add Timers driver for stm32f429 MCU > ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco > > .../ABI/testing/sysfs-bus-iio-timer-stm32 | 29 ++ > .../bindings/iio/timer/stm32-timer-trigger.txt | 23 ++ > .../devicetree/bindings/mfd/stm32-timers.txt | 46 +++ > .../devicetree/bindings/pwm/pwm-stm32.txt | 35 ++ > arch/arm/boot/dts/stm32f429.dtsi | 275 ++++++++++++++ > arch/arm/boot/dts/stm32f469-disco.dts | 28 ++ > drivers/iio/trigger/Kconfig | 9 + > drivers/iio/trigger/Makefile | 1 + > drivers/iio/trigger/stm32-timer-trigger.c | 342 ++++++++++++++++++ > drivers/mfd/Kconfig | 11 + > drivers/mfd/Makefile | 2 + > drivers/mfd/stm32-timers.c | 80 +++++ > drivers/pwm/Kconfig | 9 + > drivers/pwm/Makefile | 1 + > drivers/pwm/pwm-stm32.c | 398 +++++++++++++++++++++ > include/linux/iio/timer/stm32-timer-trigger.h | 62 ++++ > include/linux/mfd/stm32-timers.h | 71 ++++ > 17 files changed, 1422 insertions(+) > create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-timer-stm32 > create mode 100644 Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt > create mode 100644 Documentation/devicetree/bindings/mfd/stm32-timers.txt > create mode 100644 Documentation/devicetree/bindings/pwm/pwm-stm32.txt > create mode 100644 drivers/iio/trigger/stm32-timer-trigger.c > create mode 100644 drivers/mfd/stm32-timers.c > create mode 100644 drivers/pwm/pwm-stm32.c > create mode 100644 include/linux/iio/timer/stm32-timer-trigger.h > create mode 100644 include/linux/mfd/stm32-timers.h Let me know when you have all your Acks. I would be happy to take this through the MFD tree. -- Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
