On Thu, Jan 12, 2017 at 03:56:17PM +0530, Kishon Vijay Abraham I wrote:
> Add device tree binding documentation for pci dra7xx EP mode.
>
> Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
> ---
> Documentation/devicetree/bindings/pci/ti-pci.txt | 37 ++++++++++++++++++----
> 1 file changed, 30 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
> index 60e2516..62f5f59 100644
> --- a/Documentation/devicetree/bindings/pci/ti-pci.txt
> +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
> @@ -1,17 +1,22 @@
> TI PCI Controllers
>
> PCIe Designware Controller
> - - compatible: Should be "ti,dra7-pcie""
> - - reg : Two register ranges as listed in the reg-names property
> - - reg-names : The first entry must be "ti-conf" for the TI specific registers
> - The second entry must be "rc-dbics" for the designware pcie
> - registers
> - The third entry must be "config" for the PCIe configuration space
> + - compatible: Should be "ti,dra7-pcie" for RC
> + Should be "ti,dra7-pcie-ep" for EP
> - phys : list of PHY specifiers (used by generic PHY framework)
> - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
> number of PHYs as specified in *phys* property.
> - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
> where <X> is the instance number of the pcie from the HW spec.
> + - num-lanes as specified in ../designware-pcie.txt
> +
> +HOST MODE
> +=========
> + - reg : Two register ranges as listed in the reg-names property
> + - reg-names : The first entry must be "ti-conf" for the TI specific registers
> + The second entry must be "rc-dbics" for the designware pcie
> + registers
> + The third entry must be "config" for the PCIe configuration space
> - interrupts : Two interrupt entries must be specified. The first one is for
> main interrupt line and the second for MSI interrupt line.
> - #address-cells,
> @@ -19,13 +24,31 @@ PCIe Designware Controller
> #interrupt-cells,
> device_type,
> ranges,
> - num-lanes,
> interrupt-map-mask,
> interrupt-map : as specified in ../designware-pcie.txt
>
> +DEVICE MODE
> +===========
> + - reg : Four register ranges as listed in the reg-names property
> + - reg-names : "ti-conf" for the TI specific registers
> + "ep_dbics" for the standard configuration registers as
> + they are locally accessed within the DIF CS space
> + "ep_dbics2" for the standard configuration registers as
> + they are locally accessed within the DIF CS2 space
> + "addr_space" used to map remote RC address space
> + - interrupts : one interrupt entries must be specified for main interrupt.
> + - num-ib-windows : number of inbound address translation windows
> + - num-ob-windows : number of outbound address translation windows
> +
> Optional Property:
> - gpios : Should be added if a gpio line is required to drive PERST# line
>
> +NOTE: Two dt nodes should be added for each PCI controller; one for host
s/should/may/
Don't define dts source structure here. You could also have 2 files with
each config and just include the right one for each board.
We don't want overlapping memory regions defined in DT and this kind of
violates that, but I guess status is sufficient.
With that,
Acked-by: Rob Herring <robh@xxxxxxxxxx>
> +mode and another for device mode. So in order for PCI to
> +work in host mode, EP mode dt node should be disabled and in order to PCI to
> +work in EP mode, host mode dt node should be disabled. And host mode and EP
> +mode are mutually exclusive.
> +
> Example:
> axi {
> compatible = "simple-bus";
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
