Re: [PATCH 2/3] Broadcom USB DRD Phy driver for Northstar2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Kishon,

On Mon, Jan 16, 2017 at 2:52 PM, Kishon Vijay Abraham I <kishon@xxxxxx> wrote:
> Hi,
>
> On Wednesday 30 November 2016 11:25 AM, Raviteja Garimella wrote:
>> This is driver for USB DRD Phy used in Broadcom's Northstar2
>> SoC. The phy can be configured to be in Device mode or Host
>> mode based on the type of cable connected to the port. The
>> driver registers to  extcon framework to get appropriate
>> connect events for Host/Device cables connect/disconnect
>> states based on VBUS and ID interrupts.
>>
>> Signed-off-by: Raviteja Garimella <raviteja.garimella@xxxxxxxxxxxx>
>> ---
>>  drivers/phy/Kconfig              |  13 +
>>  drivers/phy/Makefile             |   1 +
>>  drivers/phy/phy-bcm-ns2-usbdrd.c | 587 +++++++++++++++++++++++++++++++++++++++
>>  3 files changed, 601 insertions(+)
>>  create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index fe00f91..b3b6a73 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -479,6 +479,19 @@ config PHY_CYGNUS_PCIE
>>         Enable this to support the Broadcom Cygnus PCIe PHY.
>>         If unsure, say N.
>>
>> +config PHY_NS2_USB_DRD
>> +     tristate "Broadcom Northstar2 USB DRD PHY support"
>> +     depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
>> +     select GENERIC_PHY
>> +     select EXTCON
>> +     default ARCH_BCM_IPROC
>> +     help
>> +       Enable this to support the Broadcom Northstar2 USB DRD PHY.
>> +       This driver initializes the PHY in either HOST or DEVICE mode.
>> +       The host or device configuration is read from device tree.
>> +
>> +       If unsure, say N.
>> +
>>  source "drivers/phy/tegra/Kconfig"
>>
>>  config PHY_NS2_PCIE
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index a534cf5..b733ba2 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -58,5 +58,6 @@ obj-$(CONFIG_PHY_TUSB1210)          += phy-tusb1210.o
>>  obj-$(CONFIG_PHY_BRCM_SATA)          += phy-brcm-sata.o
>>  obj-$(CONFIG_PHY_PISTACHIO_USB)              += phy-pistachio-usb.o
>>  obj-$(CONFIG_PHY_CYGNUS_PCIE)                += phy-bcm-cygnus-pcie.o
>> +obj-$(CONFIG_PHY_NS2_USB_DRD)                += phy-bcm-ns2-usbdrd.o
>>  obj-$(CONFIG_ARCH_TEGRA) += tegra/
>>  obj-$(CONFIG_PHY_NS2_PCIE)           += phy-bcm-ns2-pcie.o
>> diff --git a/drivers/phy/phy-bcm-ns2-usbdrd.c b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> new file mode 100644
>> index 0000000..460040d
>> --- /dev/null
>> +++ b/drivers/phy/phy-bcm-ns2-usbdrd.c
>> @@ -0,0 +1,587 @@
>> +/*
>> + * Copyright (C) 2016 Broadcom
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/extcon.h>
>> +#include <linux/gpio.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/init.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/irq.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/slab.h>
>> +#include <linux/workqueue.h>
>> +
>> +#define ICFG_DRD_AFE         0x0
>> +#define ICFG_MISC_STAT               0x18
>> +#define ICFG_DRD_P0CTL               0x1C
>> +#define ICFG_STRAP_CTRL              0x20
>> +#define ICFG_FSM_CTRL                0x24
>> +
>> +#define IDM_RST_BIT          BIT(0)
>> +#define AFE_CORERDY_VDDC     BIT(18)
>> +#define PHY_PLL_RESETB               BIT(15)
>> +#define PHY_RESETB           BIT(14)
>> +#define PHY_PLL_LOCK         BIT(0)
>> +
>> +#define DRD_DEV_MODE         BIT(20)
>> +#define OHCI_OVRCUR_POL              BIT(11)
>> +#define ICFG_OFF_MODE                BIT(6)
>> +#define PLL_LOCK_RETRY               1000
>> +
>> +#define EVT_DEVICE           0
>> +#define EVT_HOST             1
>> +#define EVT_IDLE             2
>> +
>> +#define DRD_HOST_MODE                (BIT(2) | BIT(3))
>> +#define DRD_DEVICE_MODE              (BIT(4) | BIT(5))
>> +#define DRD_HOST_VAL         0x803
>> +#define DRD_DEV_VAL          0x807
>> +#define GPIO_DELAY           20
>> +#define PHY_WQ_DELAY         msecs_to_jiffies(600)
>> +
>> +struct ns2_phy_data;
>> +struct ns2_phy_driver {
>> +     void __iomem *icfgdrd_regs;
>> +     void __iomem *idmdrd_rst_ctrl;
>> +     void __iomem *crmu_usb2_ctrl;
>> +     void __iomem *usb2h_strap_reg;
>> +     spinlock_t lock; /* spin lock for phy driver */
>> +     bool host_mode;
>> +     struct ns2_phy_data *data;
>> +     struct extcon_specific_cable_nb extcon_dev;
>> +     struct extcon_specific_cable_nb extcon_host;
>> +     struct notifier_block host_nb;
>> +     struct notifier_block dev_nb;
>> +     struct delayed_work conn_work;
>> +     struct extcon_dev *edev;
>> +     struct gpio_desc *vbus_gpiod;
>> +     struct gpio_desc *id_gpiod;
>> +     int id_irq;
>> +     int vbus_irq;
>> +     unsigned long debounce_jiffies;
>> +     struct delayed_work wq_extcon;
>> +};
>> +
>> +struct ns2_phy_data {
>> +     struct ns2_phy_driver *driver;
>> +     struct phy *phy;
>> +     int new_state;
>> +     bool poweron;
>> +};
>> +
>> +static const unsigned int usb_extcon_cable[] = {
>> +     EXTCON_USB,
>> +     EXTCON_USB_HOST,
>> +     EXTCON_NONE,
>> +};
>> +
>> +static inline int pll_lock_stat(u32 usb_reg, int reg_mask,
>> +                             struct ns2_phy_driver *driver)
>> +{
>> +     int retry = PLL_LOCK_RETRY;
>> +     u32 val;
>> +
>> +     do {
>> +             udelay(1);
>> +             val = readl(driver->icfgdrd_regs + usb_reg);
>> +             if (val & reg_mask)
>> +                     return 0;
>> +     } while (--retry > 0);
>> +
>> +     return -EBUSY;
>> +}
>> +
>> +static int ns2_drd_phy_init(struct phy *phy)
>> +{
>> +     struct ns2_phy_data *data = phy_get_drvdata(phy);
>> +     struct ns2_phy_driver *driver = data->driver;
>> +     unsigned long flags;
>> +     u32 val;
>> +
>> +     spin_lock_irqsave(&driver->lock, flags);
>> +
>> +     val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> +     if (data->new_state == EVT_HOST) {
>> +             val &= ~DRD_DEVICE_MODE;
>> +             val |= DRD_HOST_MODE;
>> +     } else {
>> +             val &= ~DRD_HOST_MODE;
>> +             val |= DRD_DEVICE_MODE;
>> +     }
>> +     writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> +     spin_unlock_irqrestore(&driver->lock, flags);
>> +     return 0;
>> +}
>> +
>> +static int ns2_drd_phy_shutdown(struct phy *phy)
>> +{
>> +     struct ns2_phy_data *data = phy_get_drvdata(phy);
>> +     struct ns2_phy_driver *driver = data->driver;
>> +     unsigned long flags;
>> +     u32 val;
>> +
>> +     spin_lock_irqsave(&driver->lock, flags);
>> +     if (!data->poweron)
>> +             goto exit;
>> +
>> +     val = readl(driver->crmu_usb2_ctrl);
>> +     val &= ~AFE_CORERDY_VDDC;
>> +     writel(val, driver->crmu_usb2_ctrl);
>> +
>> +     driver->host_mode = 0;
>> +     val = readl(driver->crmu_usb2_ctrl);
>> +     val &= ~DRD_DEV_MODE;
>> +     writel(val, driver->crmu_usb2_ctrl);
>> +
>> +     /* Disable Host and Device Mode */
>> +     val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +     val &= ~(DRD_HOST_MODE | DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> +     writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> +     data->poweron = 0;
>> +exit:
>> +     spin_unlock_irqrestore(&driver->lock, flags);
>> +     return 0;
>> +}
>> +
>> +static int ns2_drd_phy_poweron(struct phy *phy)
>> +{
>> +     struct ns2_phy_data *data = phy_get_drvdata(phy);
>> +     struct ns2_phy_driver *driver = data->driver;
>> +     u32 extcon_event = data->new_state;
>> +     unsigned long flags;
>> +     int ret;
>> +     u32 val;
>> +
>> +     spin_lock_irqsave(&driver->lock, flags);
>> +     if (extcon_event == EVT_DEVICE) {
>> +             if (data->poweron)
>> +                     goto exit;
>> +
>> +             writel(DRD_DEV_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> +             val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +             val &= ~(DRD_HOST_MODE | ICFG_OFF_MODE);
>> +             val |= DRD_DEVICE_MODE;
>> +             writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> +             val = readl(driver->idmdrd_rst_ctrl);
>> +             val &= ~IDM_RST_BIT;
>> +             writel(val, driver->idmdrd_rst_ctrl);
>> +
>> +             val = readl(driver->crmu_usb2_ctrl);
>> +             val |= (AFE_CORERDY_VDDC | DRD_DEV_MODE);
>> +             writel(val, driver->crmu_usb2_ctrl);
>> +
>> +             /* Bring PHY and PHY_PLL out of Reset */
>> +             val = readl(driver->crmu_usb2_ctrl);
>> +             val |= (PHY_PLL_RESETB | PHY_RESETB);
>> +             writel(val, driver->crmu_usb2_ctrl);
>> +
>> +             ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> +             if (ret < 0) {
>> +                     dev_err(&phy->dev, "Phy PLL lock failed\n");
>> +                     goto err_shutdown;
>> +             }
>> +     } else {
>> +             if (data->poweron && driver->host_mode)
>> +                     goto exit;
>> +
>> +             writel(DRD_HOST_VAL, driver->icfgdrd_regs + ICFG_DRD_P0CTL);
>> +
>> +             val = readl(driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +             val &= ~(DRD_DEVICE_MODE | ICFG_OFF_MODE);
>> +             val |= DRD_HOST_MODE;
>> +             writel(val, driver->icfgdrd_regs + ICFG_FSM_CTRL);
>> +
>> +             val = readl(driver->crmu_usb2_ctrl);
>> +             val |= AFE_CORERDY_VDDC;
>> +             writel(val, driver->crmu_usb2_ctrl);
>> +
>> +             ret = pll_lock_stat(ICFG_MISC_STAT, PHY_PLL_LOCK, driver);
>> +             if (ret < 0) {
>> +                     dev_err(&phy->dev, "Phy PLL lock failed\n");
>> +                     goto err_shutdown;
>> +             }
>> +
>> +             val = readl(driver->idmdrd_rst_ctrl);
>> +             val &= ~IDM_RST_BIT;
>> +             writel(val, driver->idmdrd_rst_ctrl);
>> +
>> +             /* port over current Polarity */
>> +             val = readl(driver->usb2h_strap_reg);
>> +             val |= OHCI_OVRCUR_POL;
>> +             writel(val, driver->usb2h_strap_reg);
>> +
>> +             driver->host_mode = 1;
>> +     }
>> +
>> +     data->poweron = 1;
>> +exit:
>> +     spin_unlock_irqrestore(&driver->lock, flags);
>> +     return 0;
>> +
>> +err_shutdown:
>> +     data->poweron = 1;
>> +     spin_unlock_irqrestore(&driver->lock, flags);
>> +     ns2_drd_phy_shutdown(phy);
>> +     return ret;
>> +}
>> +
>> +static void connect_work(struct work_struct *work)
>> +{
>> +     struct ns2_phy_driver *driver;
>> +     struct ns2_phy_data *data;
>> +     u32 extcon_event;
>> +
>> +     driver  = container_of(to_delayed_work(work),
>> +                            struct ns2_phy_driver, conn_work);
>> +     data = driver->data;
>> +     extcon_event = data->new_state;
>> +
>> +     if (extcon_event == EVT_DEVICE || extcon_event == EVT_HOST) {
>> +             ns2_drd_phy_init(data->phy);
>> +             ns2_drd_phy_poweron(data->phy);
>> +     } else if (extcon_event == EVT_IDLE) {
>> +             ns2_drd_phy_shutdown(data->phy);
>> +     }
>> +}
>> +
>> +static int drd_device_notify(struct notifier_block *self,
>> +                          unsigned long event, void *ptr)
>> +{
>> +     struct ns2_phy_driver *driver = container_of(self,
>> +                                     struct ns2_phy_driver, dev_nb);
>> +
>> +     if (event) {
>> +             pr_debug("Device connected\n");
>> +             driver->data->new_state = EVT_DEVICE;
>> +             schedule_delayed_work(&driver->conn_work, 0);
>> +     } else {
>> +             pr_debug("Device disconnected\n");
>> +             driver->data->new_state = EVT_IDLE;
>> +             schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> +     }
>> +
>> +     return NOTIFY_DONE;
>> +}
>> +
>> +static int drd_host_notify(struct notifier_block *self,
>> +                        unsigned long event, void *ptr)
>> +{
>> +     struct ns2_phy_driver *driver = container_of(self,
>> +                                     struct ns2_phy_driver, host_nb);
>> +
>> +     if (event) {
>> +             pr_debug("Host connected\n");
>> +             driver->data->new_state = EVT_HOST;
>> +             schedule_delayed_work(&driver->conn_work, 0);
>> +     } else {
>> +             pr_debug("Host disconnected\n");
>> +             driver->data->new_state = EVT_IDLE;
>> +             schedule_delayed_work(&driver->conn_work, PHY_WQ_DELAY);
>> +     }
>> +
>> +     return NOTIFY_DONE;
>> +}
>> +
>> +static void extcon_work(struct work_struct *work)
>> +{
>> +     struct ns2_phy_driver *driver;
>> +     int vbus;
>> +     int id;
>> +
>> +     driver  = container_of(to_delayed_work(work),
>> +                            struct ns2_phy_driver, wq_extcon);
>> +
>> +     id = gpiod_get_value_cansleep(driver->id_gpiod);
>> +     vbus = gpiod_get_value_cansleep(driver->vbus_gpiod);
>> +
>> +     if (!id && vbus) {
>> +             extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, true);
>> +     } else if (id && !vbus) {
>> +             extcon_set_cable_state_(driver->edev, EXTCON_USB_HOST, false);
>> +             extcon_set_cable_state_(driver->edev, EXTCON_USB, false);
>> +     } else if (id && vbus) {
>> +             extcon_set_cable_state_(driver->edev, EXTCON_USB, true);
>> +     }
>> +}
>> +
>> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
>> +{
>> +     struct ns2_phy_driver *driver = dev_id;
>> +
>> +     queue_delayed_work(system_power_efficient_wq, &driver->wq_extcon,
>> +                        driver->debounce_jiffies);
>> +
>> +     return IRQ_HANDLED;
>> +}
>> +
>> +static int register_extcon_notifier(struct ns2_phy_driver *phy_driver,
>> +                                 struct device *dev)
>> +{
>> +     struct extcon_dev *edev;
>> +     int ret;
>> +
>> +     phy_driver->host_nb.notifier_call = drd_host_notify;
>> +     phy_driver->dev_nb.notifier_call = drd_device_notify;
>> +
>> +     edev = phy_driver->edev;
>> +
>> +     /* Register for device change notification */
>> +     ret = extcon_register_notifier(edev, EXTCON_USB,
>> +                                    &phy_driver->dev_nb);
>> +     if (ret < 0) {
>> +             dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> +             return ret;
>> +     }
>> +
>> +     /* Register for host change notification */
>> +     ret = extcon_register_notifier(edev, EXTCON_USB_HOST,
>> +                                    &phy_driver->host_nb);
>> +     if (ret < 0) {
>> +             dev_err(dev, "can't register extcon_dev for %s\n", edev->name);
>> +             goto err_dev;
>> +     }
>> +
>> +     /* Check the device cable connect state */
>> +     ret = extcon_get_cable_state_(edev, EXTCON_USB);
>> +     if (ret < 0) {
>> +             dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> +             goto err_host;
>> +     } else if (ret) {
>> +             phy_driver->data->new_state = EVT_DEVICE;
>> +     }
>> +
>> +     /* Check the host cable connect state */
>> +     ret = extcon_get_cable_state_(edev, EXTCON_USB_HOST);
>> +     if (ret < 0) {
>> +             dev_err(dev, "can't get extcon_dev state for %s\n", edev->name);
>> +             goto err_host;
>> +     } else if (ret) {
>> +             phy_driver->data->new_state = EVT_HOST;
>> +     }
>> +
>> +     return 0;
>> +
>> +err_host:
>> +     ret = extcon_unregister_notifier(edev, EXTCON_USB_HOST,
>> +                                     &phy_driver->host_nb);
>> +err_dev:
>> +     ret = extcon_unregister_notifier(edev, EXTCON_USB,
>> +                                     &phy_driver->dev_nb);
>> +     return ret;
>> +}
>> +
>> +static struct phy_ops ops = {
>> +     .init           = ns2_drd_phy_init,
>
> Is this really being used by any controller driver? Can you point me to the
> controller driver that is using this driver?

This will be used by Synopsys UDC that's integrated into Broadcom's Northstar2
and Cygnus SoC's. I am currently working on upstream review comments for the
same in a different patch series. The "amd5536udc" driver is being modified for
platform device support (as per the suggestions I received in reviews).

>
>> +     .power_on       = ns2_drd_phy_poweron,
>> +     .power_off      = ns2_drd_phy_shutdown,
>
> missing .owner.

Will fix this.

Thanks,
Ravi
>
> Thanks
> Kishon
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux