On Mon, Jan 09, 2017 at 01:59:34PM -0800, Jaghathiswari Rankappagounder Natarajan wrote: > This binding provides interface for adding values related to ASPEED > AST2400/2500 PWM and Fan tach controller support. > The PWM controller can support upto 8 PWM output ports. > The Fan tach controller can support upto 16 tachometer inputs. > PWM clock types M, N and 0 are three types just to have three independent > PWM sources. > > Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@xxxxxxxxxx> > --- > .../devicetree/bindings/hwmon/aspeed-pwm-tacho.txt | 153 +++++++++++++++++++++ Perhaps bindings/pwm/... even though this is more than just PWM. > 1 file changed, 153 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > > diff --git a/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > new file mode 100644 > index 000000000000..8f346409ee8c > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt > @@ -0,0 +1,153 @@ > +ASPEED AST2400/AST2500 PWM and Fan Tacho controller device driver > + > +The ASPEED PWM controller can support upto 8 PWM outputs. The ASPEED Fan Tacho > +controller can support upto 16 tachometer inputs. The PWM controller supports > +3 types of frequency mode PWM for fan speed control. PWM clock types M, N and 0 > +are 3 types of frequency mode PWM just to have 3 independent PWM sources. > + > +Required properties for pwm_tacho node: > +- #address-cells : should be 1. > + > +- #size-cells : should be 1. > + > +- reg : address and length of the register set for the device. > + > +- pinctrl-names : a pinctrl state named "default" must be defined. > + > +- pinctrl-0 : phandle referencing pin configuration of the AST2400/AST2500 PWM > + ports. > + > +- compatible : should be "aspeed,aspeed2400-pwm-tacho" for AST2400 or > + "aspeed,aspeed2500-pwm-tacho" for AST2500. > + > +- clocks : a fixed clock providing input clock frequency(PWM > + and Fan Tach clock) > + > +type_values subnode format: Don't use '_' in node or property names. > +=========================== > +Under type_values subnode there can be upto 3 child nodes indicating type M/N/O > +values. Atleast one child node is required. > + > +Required properties for the child node(type M/N/O): > +- pwm_period : indicates type M/N/O PWM period, as per the AST2400/AST2500 > + datasheet. integer value in the range 0 to 255. > + > +- pwm_clock_division_l : indicates type M/N/O PWM clock division L value, > + as per the AST2400/AST2500 datasheet. > + integer value in the range 0 to 15. > + 0 here indicates divide 1, 1 indicates divide 2, > + 2 indicates divide 4, 3 indicates divide 6, and so on > + till 15 indicates divide 30. > + > +- pwm_clock_division_h : indicates type M/N/O PWM clock division H value, > + as per the AST2400/AST2500 datasheet. > + integer value in the range 0 to 15. > + 0 here indicates divide 1, 1 indicates divide 2, > + 2 indicates divide 4, 3 indicates divide 8, and so on > + till 15 indicates divide 32768. Can't you have a single divider value and driver convert to register values? Really, you should specify the PWM period in ns/us and calculate the divider based on the input clock freq. (i.e. use the clock binding). There's already PWM binding to specify the period. I think you should have a node for the fan using the PWM binding and perhaps moving some of these properties to the fan node. > + > +- fan_tach_enable : indicates fan tach enable of type M/N/O as per the > + AST2400/AST2500 datasheet. boolean value. > + > +- fan_tach_clock_division : indicates fan tach clock division as per the > + AST2400/AST2500 datasheet. > + integer value in the range 0 to 7. > + 0 indicates divide 4, 1 indicates divide 16, > + 2 indicates divide 64, 3 indicates divide 256 > + and so on till 7 indicates divide 65536. > + > +- fan_tach_mode_selection : indicates fan tach mode mode selection as per the > + AST2400/AST2500 datasheet. integer value in the > + range 0 to 2. 0 indicates falling edge, 1 indicates > + rising edge and 2 indicates both edges. > + > +- fan_tach_period : indicates fan tach period as per the AST2400/AST2500 > + datasheet. integer value (can be upto 16 bits long). > + > +pwm_port subnode format: > +======================== > +Under pwm_port subnode there can upto 8 child nodes each indicating values > +for one of the 8 PWM output ports. > + > +Required properties for each child node(starting from PWM A through PWM H): > +- enable : enable PWM #X port, X ranges from A through H. boolean value. A connection in the PWM binding would imply this. > + > +- type : indicates type selection value of PWM #X port, X ranges from A > + through H. integer value in the range 0 to 2; > + 0 indicates type M, 1 indicates type N, 2 indicates type O. This is meaningless to me. > +- fan_ctrl : set the PWM fan control initial value. integer value between > + 0(off) and 255(full speed). > + > +fan_tach_channel subnode format: > +================================ > +Under fan_tach_channel subnode there can be upto 16 child nodes each indicating > +values for one of the 16 fan tach channels. > + > +Required properties for each child node(starting from fan tach #0 through > +fan tach #16): > +- fan-ctrl-gpios : should specify the tachometer input pin on the hardware. I don't understand the connection here. You have a tach block with 16 inputs on the SoC, so why the GPIOs? If the GPIOs go to the fan, then a fan node should have the GPIO properties. > + > +- enable : enable fan tach #X, X ranges from 0 through 16. boolean value. 'status' property is the standard way to enable a node or not. Not sure if that makes sense here though. > + > +- pwm_source : indicates PWM source of fan tach #X, X ranges from 0 through 16. > + integer value in the range 0 to 7. 0 indicates PWM port A, > + 1 indicates PWM port B and so on till 7 indicates PWM port H. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
