Hi Hans,
On Sat, Dec 14, 2013 at 10:58:12PM +0100, Hans de Goede wrote:
> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
Commit-log :)
> ---
> arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 16 ++++++++++++++++
> arch/arm/boot/dts/sun4i-a10.dtsi | 16 ++++++++++++++++
> 2 files changed, 32 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
> index 425a7db..d193937 100644
> --- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
> +++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
> @@ -42,7 +42,23 @@
> };
> };
>
> + sdc0: sdc@01c0f000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdc0_pins_a>;
> + pinctrl-1 = <&mmc0_cd_pin_cubieboard>;
> + cd-gpios = <&pio 7 1 0>; /* PH1 */
> + cd-mode = <1>;
> + status = "okay";
> + };
> +
> pinctrl@01c20800 {
> + mmc0_cd_pin_cubieboard: mmc0_cd_pin@0 {
> + allwinner,pins = "PH1";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <0>;
> + allwinner,pull = <0>;
> + };
> +
You seem to be using mmc and sdc without any real distinction. Please
try to be consistent and use only one of the two (and I have a slight
preference for mmc :))
> led_pins_cubieboard: led_pins@0 {
> allwinner,pins = "PH20", "PH21";
> allwinner,function = "gpio_out";
> diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
> index 4dccdb0..13bccd5 100644
> --- a/arch/arm/boot/dts/sun4i-a10.dtsi
> +++ b/arch/arm/boot/dts/sun4i-a10.dtsi
> @@ -306,6 +306,15 @@
> #size-cells = <0>;
> };
>
> + sdc0: sdc@01c0f000 {
> + compatible = "allwinner,sun4i-mmc";
> + reg = <0x01c0f000 0x1000>;
> + clocks = <&ahb_gates 8>, <&mmc0>;
> + interrupts = <32>;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
The A10 has much more mmc controller doesn't it?
Could you add all of them in the DT ?
> intc: interrupt-controller@01c20400 {
> compatible = "allwinner,sun4i-ic";
> reg = <0x01c20400 0x400>;
> @@ -376,6 +385,13 @@
> allwinner,drive = <0>;
> allwinner,pull = <0>;
> };
> +
> + sdc0_pins_a: sdc0@0 {
> + allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
> + allwinner,function = "mmc0";
> + allwinner,drive = <3>;
> + allwinner,pull = <1>;
Wow, you need both the pullups and a 40mA output?
Ideally, I'd like this patch to be splitted into three:
- One that adds the MMC controller nodes to the DTSI
- One that adds the muxing options you need to the pinctrl node
- One that enables the controller on the boards
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
Attachment:
signature.asc
Description: Digital signature
