Hello Matt,
On Tue, Nov 29, 2016 at 10:20 PM, Matt Ranostay
<matt@ranostay.consulting> wrote:
> On Tue, Nov 29, 2016 at 9:13 AM, Javier Martinez Canillas
[snip]
>
>
>>> +- pwndn-gpio: contains a power down GPIO specifier.
>>> +- reset-gpio: contains a reset GPIO specifier.
>>> +
>>
>> I wonder if we really need a custom power sequence provider for just
>> this SDIO WiFI chip though. AFAICT the only missing piece in
>> mmc-pwrseq-simple is the power down GPIO property, so maybe
>> mmc-pwrseq-simple could be extended instead to have an optional
>> powerdown-gpios property and instead in the Marvell SD8787 DT binding
>> can be mentioned which mmc-pwrseq-simple properties are required for
>> the device.
>>
>
> The reason we didn't do that is we need delay between the two
> assertions/desertions of GPIOs. It wouldn't seems good practice to
> hack the pwrseq-simple for this...
>
Yes, I noticed that. I wouldn't say that it would be a hack for the
pwrseq-simple since it already has a "post-power-on-delay-ms" DT
property, so AFAICT it would just be adding a "pre-power-on-delay-ms"
property for your use case.
It would also be more consistent since it would support a delay for
pre and post power callbacks. It would also make you avoid hardcoding
the 300 msec wait, in case other device has a similar need but with a
different wait time.
In summary, I think that devices having a power (or power down) and
enable GPIO, and needing to wait between the GPIO toggling are common.
So I would prefer to make pwrseq-simple usable for these instead of
adding device specific power sequence providers. But it's just my
opinion and not my call :-)
>>> +Example:
>>> +
>>> + wifi_pwrseq: wifi_pwrseq {
>>> + compatible = "mmc-pwrseq-sd8787";
>>> + pwrdn-gpio = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
>>> + reset-gpio = <&twl_gpio 1 GPIO_ACTIVE_LOW>;
>>> + }
>>> diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
>>
>> Does this patch depend on a previous posted series? I don't see this
>> file in today's linux-next...
>
> Got renamed to ->
> Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt it
> seems very recently.
>
I see, that's what I thought but I wasn't able to find the commit /
patch that did it.
>>
>>> index c421aba0a5bc..08fd65d35725 100644
>>> --- a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
>>> +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
>>> @@ -32,6 +32,9 @@ Optional properties:
>>> so that the wifi chip can wakeup host platform under certain condition.
>>> during system resume, the irq will be disabled to make sure
>>> unnecessary interrupt is not received.
>>> + - vmmc-supply: a phandle of a regulator, supplying VCC to the card
>>> + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*"
>>> + for documentation of MMC power sequence bindings.
>>>
>>> Example:
>>>
>>> @@ -44,6 +47,7 @@ so that firmware can wakeup host using this device side pin.
>>> &mmc3 {
>>> status = "okay";
>>> vmmc-supply = <&wlan_en_reg>;
>>> + mmc-pwrseq = <&wifi_pwrseq>;
>>> bus-width = <4>;
>>> cap-power-off-card;
>>> keep-power-in-suspend;
>>
>> I think this change should be split in a separate patch as well.
>>
You didn't answer about this, but I guess you agree it should be in a
separate patch.
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
