Re: [PATCH v2 2/4] usb: dwc2: Add binding for AHB burst

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 11/22/2016 12:51 PM, Christian Lamparter wrote:
> On Monday, November 21, 2016 7:32:30 PM CET John Youn wrote:
>> On 11/21/2016 1:10 PM, Christian Lamparter wrote:
>>> On Monday, November 21, 2016 12:16:31 PM CET John Youn wrote:
>>>> On 11/18/2016 12:18 PM, Christian Lamparter wrote:
>>>>> On Friday, November 18, 2016 8:16:08 AM CET Rob Herring wrote:
>>>>>> Also, perhaps you should allow that the compatible string can define the 
>>>>>> default.
>>>>>>
>>>>> I hoped you would say that :).
>>>>>
>>>>> I've attached a patch (on top of John Youn changes) [...]
>>>>> ---
>>>>> Subject: [PATCH] usb: dwc2: add a default ahb-burst setting for amcc,dwc-otg
>>>>> [...]
>>>>> @@ -1097,6 +1097,22 @@ static const char *const ahb_bursts[] = {
>>>>> +/* [...] */
>>>>> +static const struct of_device_id dwc2_compat_ahb_bursts[] = {
>>>>> +	{
>>>>> +		.compatible = "amcc,dwc-otg",
>>>>> +		.data = (void *) GAHBCFG_HBSTLEN_INCR16,
>>>>> +	},
>>>>> +};
>> [...]
>>>>>> @@ -1107,6 +1123,12 @@ static int dwc2_get_property_ahb_burst(struct dwc2_hsotg *hsotg)
>>>>>  	ret = device_property_read_string(hsotg->dev, "snps,ahb-burst", &str);
>>>>>  	if (ret < 0) {
>>>>> +		const struct of_device_id *match;
>>>>> +
>>>>> +		match = of_match_node(dwc2_compat_ahb_bursts, node);
>>>>> +		if (match)
>>>>> +			ret = (int)match->data;
>>>>> +
>> [...]
>>>> I'd prefer if you use the binding which requires no extra code in
>>>> dwc2.
>>> I'm fine with either option. However it think that this would require
>>> that either Mark or Rob would allow an exception to the "keep existing
>>> dts the way they are) and ack the following change to the canyonlands.dts. 
>>
>> I don't know about that. Under what circumstance can the dts change?
> As far as I know, the justification for not changing the DTS is that a
> compiled DTB might be stored in an read-only ROM on a board. So it would
> be impossible to update it. Hence, the driver have work with the existing
> (and sometimes buggy or incomplete) information to stay compatible.
> 
> (Note: Thankfully, the canyonlands dtb is stored in flash, it's possible
> to update it. But it is an extra step that's not done automatically
> with make install). 
> 
>> The canyonlands dts was binding to an external vendor driver. So it
>> wasn't documented nor expected to work with dwc2 until your recent
>> patch adding the compatible string.
> 
> Oh, no that's not what happend. Let me explain why there was no "external 
> vendor driver": AMCC/APM were planing to upstream their hole platform. And
> in fact, the devs tried very hard to include their driver back in 2011 [0].
> But this driver was denied inclusion back then due to:
> 
> "[...]
> I would also like to point out that the same Synopsys USB controller
> is used in a number of other SoCs (especially ARM chips), and
> supported by other drivers, some of these even in mainline.
> 
> See http://thread.gmane.org/gmane.linux.usb.general/61714/focus=62139
> for a related thread.
> 
> Instead of trying to add a completely new driver to mainline (and one
> which has been repeatedly been rejected), I vote for focusing on the
> existing driver code that is already in mainline, and testing and
> improving this so we can use a single implementation of this driver
> code for all SoCs that use the same IP block." [1]
> 
> Of course: The listed link goes the "USB Host driver for i.MX28" driver.
> And this is an ehci-hcd like driver... Which is as you are well aware not
> that similar to the dwc2 OTG. And as far as I can tell: AMCC abandoned
> the patch series right there. 
> 
> Note: AMCC did however succeed in pushing your employer's Synopsys
> DesignWare SATA and DMA drivers to the kernel back then. And I'm happy
> to report that both drivers are still around and working fine for the 460EX 
> (sata_dwc_460ex.c[2] and the DW AHB DMA [3]). (The drivers also work for
> different platforms than the original PPC. I know that because I helped
> Andy Shevchenko with testing and pushing some fixes to it when he was
> adding support for the Intel Quark SoC, which uses the DWC SATA and DMA).

Ok thanks for clearing that up. I understand.

For now we can just set the property to "INCR16" based on the
compatible string. Perhaps in the future do this from a glue-layer
driver which binds to all compatible strings other than "snps,dwc2".

I won't be able to do anything with this until next week though.

Regards,
John
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux